tribulation BYES 104 Power supply unit (DR-ID 800MP) DR800MP Caution Label 1 —E2> DR-ID POMPOM System Label —} DR-ID 600PU Rating Label Battery charger {optional} Battery charger Rating Label Rating Lats! AC adapter for cradle (optional) AG adapter for cradle Rating Label 1.6.
Oneida ages Loy 1.6.4 Safety and Other Symbols The following safety symbols are used in the labels or on its body. Symbol Description C € 8123 This symbol indicates compliance of the equipment with Directive 93/42/EEC. Caution (See "1.6.1 Locations of Labels” (page OFF (To indicate disconnection from the mains, at least for mains switches or their positions, and all those cases where safety is involved.
I 1.7 Installation Conditions 1.7.1 Installation Space When Setting the Control Cabinet in the X-ray Room Do not Install the power supply unit, control cabinet, image processing unit, Battery charger {optional} and Access point in an area of the X-ray room, where the user can easily trip over. Fails could result in injury. In case that the control cabinet is installed in the X-ray room, ensure a certain distance between the control cabinet and the upright-type or bed-type radio graphic examination stand.
chapter System Configuration (Product Overview) | 2.1 FDRD-EVO 2.1.1 System Configuration For the U.S.
(MtAI0AQ polygon) uopenbyuos Walsh nN 2.1.2 Features of the FDR D-EVE This section describes the main features of the FDR D-EVE. 1 The external dimensions and the weight of the flat panel sensor are the same as those of the conventional cassette used for general exposure. Due to this feature, the flat pane! sensor can be inserted into the radio graphic examination stand that has been used, allowing the user to avoid cassette replacement.
I 2.2 Unit Names and the Functions Unit names and the functions of the FDR D-EVE are described below. 2.21 DR-D 600 u DR-ID 600PU a Applied part Connector tats | Connector us lamp Status lamp Fiat panel sensor Flat panel sensor (DR-D 6135E) {DR-1 6018E, DR-ID 6028E, DR-ID 8115E and DR-D 6128E) * Exposure plane is shown In this figure, * Exposure plans is shown in this figure, Ray, Applied part Shock sensor display (2 places) + Lights red when the shock sensor detects a severs impact.
{mapping Jonson) nonempty) waists nymph "wm DR-ID 600MC Main switch! power status LED Control cabinet (DR-ID 600MC} Name ] Description Control cabinet A personal computer used for controlling the flat panel sensor and 600MC} performing image processing. Main switch Supplies the power to the control cabinet. Power status LED Displays ON/OFF of the control cabinet. é Depending on the configuration, the control cabinet (DR-ID 800MC) may not be included in the system.
m AC adapter for cradle (optional) SE cable for charging AC adapter AC adapter for cradle Name Description i AC adapter for cardie Charge the flat panel sensor (DR-ID 801ST, DR-ID 8028E, DR-ID 6118, DR-ID 6128E and DR-ID 8138E) by combining it with the separately sold cradle or Cradle for 24, (AN cautions) + Do not connect directly to the flat panel sensor when the AC adapter for cradle is not connected to the cradle.
{ma1n12A0 beanpole) vogemByno) whiskeys mmN)em 2.3 Image Processing Unit’s Display Configuration When the self-initialization process ends, the Patient Information Input Screen will appear on the image processing unit's display. © For details, see "DR-ID 300CL Operation Manual”. = Patient Information Input Screen Patient information input flied Input patient information. Tool button Operates the Patient information Database function to input patient information.
m Connected Devices Status Details on each icon and its display area are described below. Other indicator icons display area Other indicator icons display area “The status of the flat panel sensor and that of the image processing unit are displayed as icons. The status of each connected device is shown in three categories. Device information displayed in each category is as follows.
{messenger 1anp0id) uoneinfiyuo) wayside (1) Exposure Unit Communication Indicator The following icons display communication status of the flat panel sensor corresponding to the selector selected in the exposure unit display field of the "Study screen”. H the flat panel sensor has a wired connection, the following icons are displayed. 5 : Connected -B : Disconnected If the flat panel sensor is connects tirelessly, the following icons are displayed.
| 2.4 Routine Operation Diagram The system configuration and the routine operation diagram for the FDR D-EVE is as follows. FDR D-EVE (DR-ID 600) DR-ID 800PU and DR-ID 600MC DR-ID 300CL « X-ray exposure « Image reading — image data « Patient information entry « Exposure region / study menu selection « Image processing, etc.
{mauve Jonson) uonembyuos waists Meany [2.5 Wireless Specifications 1 Technical Specification : IEEE802.11.n (protocol) , W52 (frequency) 2 Intended environment : Room size of 10m X 10m x 3m (32.8 ft x 32.8 (height) or less (general X-ray room} {The electric shield does not exist excluding the installation stand or pd) 3 Installation: DR-ID 6138E and Access Point must be installed in the same room. Do riot place Access Point within the reach of patients.
chapter 3 Basic Operation | 3.1 Preparing the Flat Panel Sensor This section describes how to prepare the flat panel sensor. 3.1.1 Type of Flat Panel Sensor DR-ID 801ST, DR-ID 802SE, DR-ID 8118E, DR-ID 612SE and DR-ID 6138E : Wireless communication mode or wired communication mode is available. When used in wireless communication mode, an access point™, battery pack (optional) and battery charger (optional) are required. *1 In the countries other than the U.S.
rnp waged Wiseguy 3.1.3 Connecting/Disconnecting the Flat Panel Sensor (DR-ID 601ST, DID 602SE, DR-ID 611SE, DR-D 612SE and DR-ID 613SE) Connector When used in wireless communication mode, disconnect the connector. 0 Disconnect the connector, : 2] Connect the connector. Press the latches on both sides of the connector. Press the connector into the insertion section.
3.1.4 Connecting/Disconnecting the Sensor Cable Relay Connector for the Flat Panel Sensor (DR-ID 600SE) Folio the procedure below to connect/disconnect the sensor cable relay connector. » Do not connect the flat panel sensor to the power supply unit other than of the FDR D-EVE. Otherwise, the connector may be damaged. « Do not connect the flat panel sensor unregistered fo the system. Otherwise, the power to the flat panel sensor will be disconnected automatically.
rapeseed side lpm: 3.1.5 Connecting/Disconnecting the AC adapter for cradle (optional) Relay Connector Folio the procedure below to connect/disconnect the AC adapter for cradle relay connector. + When connecting/disconnecting relay connector, always hold the grip of the connector. ‘The wire inside may be broken, if you disconnectedness by holding the cable. + Do not drop relay connector when connecting/disconnecting it. Otherwise, personal injury may result, or properties or the connector may be damaged.
3.1.6 Inserting/Removing the Flat Panel Sensor into/from the Radio graphic Examination Stand Follow the procedure below to insertions the flat panel sensor into/from the radio graphic examination stand, © For details, see the Operation Manual for the radio graphic examination stand.
TERR needed disguise [1] Upright type When inserting from the right-hand side (AN cautions When inserting the flat panel sensor into the radio graphic examination stand, direct the exposure plane toward the X-ray tube. Pull out the tray.
[2] Bed type AN cautions) When inserting the flat panel sensor ta the radio graphic examination stand, direct the exposure plane upwards. a Pull out the tray by using the handle. When setting the flat panel sensor horizontally, position the connector as shown in the figure below. BAB Pull the cassette stopper, and set the flat panel sensor so that its center mark is aligned with the center of the stopper.
uopeisdg ses cope 3.1.8 Charging the Battery Pack (Optional) for the Flat Panel Sensor (DR-ID 601ST, DR-ID 602SE, DR-ID 611SE, DR-ID 612SE and DR-ID 613SE) When used in wireless communication mode, charge the battery pack (optional) using the battery charger (optional). CAUTIONS Do not charge the battery pack other than those designated by FUJI FILM Corporation.
a Set the battery pack in the battery charger. When battery charge is completed, remove the battery pack. When the battery pack is set, a buzzer sand is "YP generated and the charge status indicator LED : When battery charge is completed, the chars status fights. : indicator LED changes from blinking to fighting. Three battery packs can be charged at the same : time. 3.1.