For Safe Operation DIGITAL RADIOGRAPHY FUJIFILM DR System &RQ¿JXUDWLRQ (Product Overview) (DR-ID 600) Basic Operation Operation Manual 6st Edition: October 2010 7URXEOHVKRRWLQJ Daily Inspection and Maintenance Appendix Maintenance and Inspection This Operation Manual describes details on how to operate the FDR D-EVO and cautions to be observed when operating it.
ii FDR D-EVO Operation Manual 897N101473E
Introduction 7KH :LUHG :LUHOHVV )'5 ' (92 '5 ,' ÀDW SDQHO GHWHFWRU V\VWHP LV LQWHQGHG WR FDSWXUH for display radiographic images of human anatomy. It is intended for use in general projection UDGLRJUDSKLF DSSOLFDWLRQV ZKHUHYHU FRQYHQWLRQDO ¿OP VFUHHQ RU &5 V\VWHPV PD\ EH XVHG 7KH )'5 ' (92 '5 ,' LV QRW LQWHQGHG IRU PDPPRJUDSK\ ÀXRURVFRS\ WRPRJUDSK\ DQG DQJLRJUDSK\ applications.
FDR D-EVO System Operation Manuals DIGITAL RADIOGRAPHY FDR D-EVO (DR-ID 600) Operation Manual DR-ID 600PU Operation Manual DR-ID 300CL Operation Manual See “DR-ID 300CL Operation Manual” along with the manuals for the related products. The DR-ID 600MC runs on a commercially available personal computer. However, operations are not required to use the FDR D-EVO. For operations of a commercially available personal computer, see the operation manual provided by the manufacturer.
Contents at a Glance For Safe Operation Chapter Chapter 1 2 This chapter presents Warnings and Cautions we wish you to observe for safe operation of the FDR D-EVO. 6\VWHP &RQ¿JXUDWLRQ 3URGXFW 2YHUYLHZ This chapter gives the various unit names and describes their functions and features of the FDR D-EVO. Basic Operation Chapter 3 This chapter describes start-up, shut-down and other basic operations of the FDR D-EVO.
How to Read This Manual %DVLF SDJH OD\RXW 3OHDVH KDYH D JRRG JUDVS RI WKH EDVLF SDJH FRQ¿JXUDWLRQ RI WKLV 2SHUDWLRQ 0DQXDO DV LOOXVWUDWHG EHORZ IRU \RX WR XVH LW PRUH HI¿FLHQWO\ Section title Lead Shows the title of an operation procedure described in the section. Describes information we wish you to know in advance of your operating the system or information that may help you to operate it. 3.
0DUNV Information items to be observed when you are operating this system and the supplementary remarks are described in this manual with the respective marks. For the safe system operation, be sure to observe Warning/Caution. WARNING Indicates hazardous situations that may lead to serious injuries or even death if the precaution is not or cannot be followed. CAUTIONS Indicates hazardous situations that may lead to mild or moderate injury or physical damages if the caution is not or cannot be followed.
Contents Introduction ...........................................................................................................................iii FDR D-EVO System Operation Manuals .............................................................................iv Contents at a Glance ............................................................................................................ v How to Read This Manual ............................................................................................
3.2 Starting Up and Shutting Down the System ............................................................ 3-7 3.2.1 3.2.2 3.3 Starting Up the System ............................................................................................3-7 Shutting Down the System ......................................................................................3-8 Routine Operations .................................................................................................
Z.3 Precautions for Exposure in SEMI-X MODE ...........................................................Z-5 Z.4 Precautions for Exposure in FIX MODE ..................................................................Z-6 Z.5 Other Precautions ...................................................................................................Z-7 Z.5.1 Z.5.2 Z.5.3 Z.5.4 Z.5.5 Z.5.6 Z.5.7 Z.5.8 Precautions for Exposure of a Subject in Relatively Large Contrast .......................
Chapter 1 For Safe Operation 3UHFDXWLRQV %HIRUH 2SHUDWLQJ 7KLV (TXLSPHQW 1 For Safe Operation Before using this equipment, please read “Precautions Before Operating This Equipment” carefully so that you can operate it correctly. Whenever you operate this equipment, be sure to observe those precautions. Failure to do so may cause you to subject to injuries or property damage to occur. The institution where the equipment is installed is responsible for its use and maintenance.
1.2 Precautions to be Observed When 8VLQJ WKH (OHFWULF 0HGLFDO (TXLSPHQW We ask that you observe these usage precautions and use the equipment correctly. 1. This equipment should be used only by people who have the proper skills. 2. Observe the following precautions when installing the equipment. 2-1. Install the equipment where water will not splash it. 2-2.
1.3 Safety Before using the FDR D-EVO, read this section thoroughly to ensure that you use the product properly. (OHFWULF 6KRFN :DUQLQJV DQG &DXWLRQV 1 WARNING For Safe Operation The power supply to the FDR D-EVO is AC100 to 240V. 7R DYRLG HOHFWULF VKRFNV XVHUV VKRXOG DOZD\V WDNH WKH IROORZLQJ SUHFDXWLRQV Ɣ 1HYHU RSHQ DQ\ FRYHUV RI WKH HTXLSPHQW Ɣ ,QVWDOO WKH HTXLSPHQW LQ D ORFDWLRQ ZKHUH LW ZLOO QRW EH H[SRVHG WR ZDWHU Ɣ &KHFN WKDW WKH HTXLSPHQW LV VHFXUHO\ HDUWKHG Ɣ &KHFN WKDW DOO RI WKH FRU
WARNING 'R QRW GLVDVVHPEOH RU UHPRGHO WKH HTXLSPHQW 2WKHUZLVH ¿UH RU HOHFWULF VKRFN PD\ UHVXOW .HHS DZD\ IURP WKH SDUWV LQVLGH WKH SURGXFW ZKLFK PD\ FDXVH HOHFWULF VKRFN ,I \RX WRXFK them accidentally, death or severe injury may result. WARNING 1 'R QRW KLW RU GURS WKH HTXLSPHQW RU VXEMHFW LW WR VHYHUH VKRFN 2WKHUZLVH WKH HTXLSPHQW PD\ EH GDPDJHG ,I WKH GDPDJHG HTXLSPHQW LV XVHG ¿UH RU HOHFWULF VKRFN PD\ UHVXOW For Safe Operation WARNING %HIRUH XVLQJ WKH ÀDW SDQHO VHQVRU '5 ,' 6( PDNH
:DUQLQJV IRU $EQRUPDOLWLHV WARNING ,I DQ\ RI WKH IROORZLQJ RFFXUV LPPHGLDWHO\ WXUQ RII WKH SRZHU RI HDFK XQLW XQSOXJ WKH SRZHU cable from the outlet, and then contact a FUJIFILM dealer. Ɣ :KHQ VPRNH VWUDQJH RGRU RU DEQRUPDO VRXQG LV SUHVHQW Ɣ :KHQ D IRUHLJQ REMHFW VXFK DV D PHWDO REMHFW RU OLTXLG HQWHUV WKH SURGXFW Ɣ :KHQ WKH HTXLSPHQW LV GURSSHG RU KLW DQG LV GDPDJHG 1 For Safe Operation Installation Precautions CAUTIONS 'R QRW LQVWDOO WKH V\VWHP LQ D ORFDWLRQ ZLWK WKH IROORZLQJ FRQGLWLRQV
WARNING .HHS HTXLSPHQW RWKHU WKDQ WKRVH XVHG IRU SDWLHQWV RXW RI WKHLU UHDFK WR HQVXUH DSSURSULDWH system isolation. WARNING Do not move the Console from where it is installed. 1 For Safe Operation Software Precautions CAUTIONS Do not install additional software to the system. Do not uninstall any of the software preinstalled in the system. The system is preinstalled with the appropriate software. If other software is installed or if the H[LVWLQJ VRIWZDUH LV XQLQVWDOOHG YDULRXV RSHUDWLRQDO HUURUV PD\ U
3UHFDXWLRQV IRU &KDUJLQJ WKH %DWWHU\ CAUTIONS 2EVHUYH WKH IROORZLQJ SUHFDXWLRQV ZKHQ FKDUJLQJ WKH EDWWHU\ SDFN RSWLRQDO XVLQJ WKH EDWWHU\ FKDUJHU RSWLRQDO Ɣ 'R QRW XVH WKH EDWWHU\ SDFN 1 RU EDWWHU\ FKDUJHU LQ FRPELQDWLRQ ZLWK DQ\ EDWWHU\ SDFN RU EDWWHU\ FKDUJHU LQFOXGLQJ WKH $& DGDSWHU RWKHU WKDQ WKRVH UHFRPPHQGHG E\ FUJIFILM Corporation. Ɣ 'R QRW GLVDVVHPEOH RU FRQYHUW WKH EDWWHU\ SDFN RU EDWWHU\ FKDUJHU Ɣ ,I WKH EDWWHU\ SDFN RU EDWWHU\ FKDUJHU EHFRPHV IDXOW\ FRQVXOW RXU RI¿FLDO
(OHFWURPDJQHWLF &RPSDWLELOLW\ (0& 1.4.1 DR-ID 600PU and DR-ID 300CL This equipment has been tested and found to comply with the limits for medical devices to the IEC $ (1 $ 0HGLFDO 'HYLFH 'LUHFWLYH ((& These limits are designed to provide reasonable protection against harmful interference in a typical medical installation.
Further information for IEC 60601-1-2 (EN60601-1-2) 1. Medical electrical equipment needs special precautions regarding EMC and needs to be installed and put into service according to the EMC information provided in the accompanying documents. 2. Portable and mobile RF communications equipment can affect medical electrical equipment. 3. Information regarding the cable affecting EMC is as follows.
Table 2 *XLGDQFH DQG PDQXIDFWXUHU¶V GHFODUDWLRQ HOHFWURPDJQHWLF LPPXQLW\ 7KH '5 ,' 38 DQG WKH '5 ,' &/ DUH LQWHQGHG IRU XVH LQ WKH HOHFWURPDJQHWLF HQYLURQPHQW VSHFL¿HG EHORZ The customer or the user of the DR-ID 600PU and the DR-ID 300CL should assure that they are used in such an environment.
Table 3 *XLGDQFH DQG PDQXIDFWXUHU¶V GHFODUDWLRQ HOHFWURPDJQHWLF LPPXQLW\ 7KH '5 ,' 38 DQG WKH '5 ,' &/ DUH LQWHQGHG IRU XVH LQ WKH HOHFWURPDJQHWLF HQYLURQPHQW VSHFL¿HG EHORZ The customer or the user of the DR-ID 600PU and the DR-ID 300CL should assure that they are used in such an environment.
Table 4 Recommended separation distances between 3RUWDEOH DQG PRELOH 5) FRPPXQLFDWLRQV HTXLSPHQW DQG WKH '5 ,' 38 DQG WKH '5 ,' &/ The DR-ID 600PU and the DR-ID 300CL are intended for use in the electromagnetic environment in which radiated RF disturbances are controlled.
1.4.2 DR-ID 600MC This equipment has been tested and found to comply with the international standard for medical GHYLFHV EHORZ DFFRUGLQJ WR WKH UHTXLUHPHQW RI WKH ,(& $ (1 $ (0& 6WDQGDUG &,635 (1 &,635 (1 (1 ,(& (1 ,(& 1 For Safe Operation This does not guarantee that there is no harmful electromagnetic interference under any installation environment.
Table 1 *XLGDQFH DQG PDQXIDFWXUHU¶V GHFODUDWLRQ HOHFWURPDJQHWLF HPLVVLRQV 7KH '5 ,' 0& LV LQWHQGHG IRU XVH LQ WKH HOHFWURPDJQHWLF HQYLURQPHQW VSHFL¿HG EHORZ The customer or the user of the DR-ID 600MC should assure that it is used in such an environment.
Table 3 *XLGDQFH DQG PDQXIDFWXUHU¶V GHFODUDWLRQ HOHFWURPDJQHWLF LPPXQLW\ 7KH '5 ,' 0& LV LQWHQGHG IRU XVH LQ WKH HOHFWURPDJQHWLF HQYLURQPHQW VSHFL¿HG EHORZ The customer or the user of the DR-ID 600MC should assure that it is used in such an environment.
3UHFDXWLRQV LQ 8VLQJ WKH )'5 ' (92 This section describes the precautions in using the FDR D-EVO. +DQGOLQJ 1 For Safe Operation +DQGOH WKH ÀDW SDQHO VHQVRU FDUHIXOO\ VLQFH LW LV manufactured with precision. ,I WKH ÀDW SDQHO VHQVRU LV KLW RU GURSSHG RU LV VXEMHFW WR severe shock, it may be damaged. ,I WKH IURQW DQG UHDU RI WKH ÀDW SDQHO VHQVRU DUH VXEMHFW WR impact by a projection, it may be damaged. 7KH ÀDW SDQHO VHQVRU LV HTXLSSHG ZLWK D VKRFN VHQVRU that detects a severe impact.
1.5.2 Before Exposure The use of an air-conditioner may dramatically changes the temperature of the room where the system is installed. This may cause dew condensation on the system, resulting in quality problems. When an air-conditioner is used, change the temperature gradually to avoid temperature variation in order not to cause dew condensation. ,I DQ H[SRVXUH LV PDGH ZLWK WKH IURQW DQG UHDU RI WKH ÀDW SDQHO sensor facing the other way round, re-exposure and electric parts may be damaged.
/RFDWLRQV RI /DEHOV DQG 6LJQV /RFDWLRQV RI ODEHOV DQG VLJQV DI¿[HG WR WKH )'5 ' (92 DQG WKH UHOHYDQW VDIHW\ VLJQV DUH VKRZQ EHORZ 1.6.
1.6.2 DR-ID 600 Sample year of manufacture DR-ID 601SE CE Mark Label 1 Sample year of manufacture For Safe Operation DR-ID 600SE CE Mark Label MAR. 2010 DR-ID 600MP System Label Battery charger Rating Label DR-ID 600MC Identification Label AC adapter (Battery charger) Rating Label Access point Rating Label* DR-ID 300CL Identification Label Battery pack Rating Label AC adapter (Access point) Rating Label* * The access point model is subject to change.
1.6.
1.6.4 Safety and Other Symbols The following safety symbols are used in the labels or on its body. Symbol Description This symbol indicates compliance of the equipment with Directive 93/42/EEC. 1 Caution (See “1.6.1 Locations of Labels” (page 1-17).) For Safe Operation OFF (To indicate disconnection from the mains, at least for mains switches or their positions, and all those cases where safety is involved.
1.7 Installation Conditions ,QVWDOODWLRQ 6SDFH :KHQ 6HWWLQJ WKH &RQWURO &DELQHW LQ the X-ray Room In case that the control cabinet is installed in the X-ray room, ensure a certain distance between WKH FRQWURO FDELQHW DQG WKH XSULJKW W\SH RU EHG W\SH UDGLRJUDSKLF H[DPLQDWLRQ VWDQG 6HH WKH ¿JXUH below for reference. )RU WKH SURGXFWV WKDW FDQ EH LQVWDOOHG LQ SDWLHQW HQYLURQPHQW VHH ³ 6\VWHP &RQ¿JXUDWLRQ´ (page 2-1). 1 For Safe Operation CAUTIONS 'R QRW LQVWDOO WKH SRZHU VXSSO\ XQLW FRQWURO
Chapter 2 \VWHP &RQILJXUDWLRQ 6 (Product Overview) 2.1 FDR D-EVO 6\VWHP &RQ¿ JXUDWLRQ For the U.S.
2.1.2 Features of the FDR D-EVO This section describes the main features of the FDR D-EVO. 7KH H[WHUQDO GLPHQVLRQV DQG WKH ZHLJKW RI WKH ÀDW SDQHO VHQVRU DUH WKH VDPH DV WKRVH RI WKH FRQYHQWLRQDO FDVVHWWH XVHG IRU JHQHUDO H[SRVXUH 'XH WR WKLV IHDWXUH WKH ÀDW SDQHO sensor can be inserted into the radiographic examination stand that has been used, allowing the user to avoid cassette replacement. 7KH ÀDW SDQHO VHQVRU FDQ EH FRQQHFWHG GLVFRQQHFWHG ZLWK WKH UHOD\ FRQQHFWRU RI WKH FRQQHFWLRQ FDEOH 7KL
2.2 Unit Names and the Functions Unit names and the functions of the FDR D-EVO are described below. 2.2.1 DR-ID 600 Ŷ DR-ID 600PU Shock sensor display (2 places) : Lights red when the shock sensor detects a severe impact. 2 6\VWHP &RQILJXUDWLRQ 3URGXFW 2YHUYLHZ Connector Status lamp Power status LED Flat panel sensor (DR-ID 601SE) * Exposure plane is shown in this figure. Main switch Shock sensor display (2 places) : Lights red when the shock sensor detects a severe impact.
Ŷ DR-ID 600MC Main switch/ power status LED 2 Control cabinet (DR-ID 600MC) 6\VWHP &RQILJXUDWLRQ 3URGXFW 2YHUYLHZ Name Description $ SHUVRQDO FRPSXWHU XVHG IRU FRQWUROOLQJ WKH ÀDW SDQHO VHQVRU DQG performing image processing. Control cabinet (DR-ID 600MC) Main switch Supplies the power to the control cabinet. Power status LED Displays ON/OFF of the control cabinet. Ŷ %DWWHU\ FKDUJHU 2SWLRQDO Battery charger Name Description &KDUJHV WKH EDWWHU\ SDFN RSWLRQDO IRU WKH ÀDW SDQHO VHQVRU '5 ,
&RQVROH 'LVSOD\ &RQILJXUDWLRQ When the self-initialization process ends, the Patient Information Input Screen will appear on the Console display. For details, see “DR-ID 300CL Operation Manual”. List tab Displays various lists. Patient information input field Input patient information. Turns one page backward. Shows page number of the patient information input field. 2 Turns one page forward. Clears patient information (except for technologist). 6\VWHP &RQILJXUDWLRQ 3URGXFW 2YHUYLHZ Operates the
5RXWLQH 2SHUDWLRQ 'LDJUDP 7KH V\VWHP FRQ¿JXUDWLRQ DQG WKH URXWLQH RSHUDWLRQ GLDJUDP IRU WKH )'5 ' (92 LV DV IROORZV FDR D-EVO (DR-ID 600) DR-ID 600PU and DR-ID 600MC 2 X-ray exposure Image reading DR-ID 300CL Image data Patient information entry Exposure region / study menu selection 6\VWHP &RQILJXUDWLRQ 3URGXFW 2YHUYLHZ Image processing, etc.
Chapter 3 Basic Operation 3UHSDULQJ WKH )ODW 3DQHO 6HQVRU 7KLV VHFWLRQ GHVFULEHV KRZ WR SUHSDUH WKH ÀDW SDQHO VHQVRU 3.1.1 Type of Flat Panel Sensor '5 ,' 6( :LUHOHVV FRPPXQLFDWLRQ PRGH RU ZLUHG FRPPXQLFDWLRQ PRGH LV DYDLODEOH :KHQ used in wireless communication mode, an access point*1, battery pack (optional) and battery charger (optional) are required. *1 In the countries other than the U.S., an access point is not included as a component of the system.
&RQQHFWLQJ 'LVFRQQHFWLQJ WKH 6HQVRU &DEOH 5HOD\ Connector for the Flat Panel Sensor (DR-ID 600SE) Follow the procedure below to connect/disconnect the sensor cable relay connector. 'R QRW FRQQHFW WKH ÀDW SDQHO VHQVRU WR WKH SRZHU VXSSO\ XQLW RWKHU WKDQ RI WKH )'5 ' (92 2WKHUZLVH WKH FRQQHFWRU PD\ EH GDPDJHG 'R QRW FRQQHFW WKH ÀDW SDQHO VHQVRU XQUHJLVWHUHG WR WKH V\VWHP 2WKHUZLVH WKH SRZHU WR WKH ÀDW SDQHO VHQVRU ZLOO EH GLVFRQQHFWHG DXWRPDWLFDOO\ )RU GHWDLOV RQ WKH UHJLVWUDWLRQ FRQWDF
,QVHUWLQJ 5HPRYLQJ WKH )ODW 3DQHO 6HQVRU LQWR IURP WKH 5DGLRJUDSKLF ([DPLQDWLRQ 6WDQG )ROORZ WKH SURFHGXUH EHORZ WR LQVHUW UHPRYH WKH ÀDW SDQHO VHQVRU LQWR IURP WKH UDGLRJUDSKLF examination stand. For details, see the Operation Manual for the radiographic examination stand. CAUTIONS )RU WKH SRVLWLRQLQJ DW WKH WLPH RI LQVHUWLQJ UHPRYLQJ WKH ÀDW SDQHO VHQVRU VHH WKH 2SHUDWLRQ 0DQXDO IRU WKH UDGLRJUDSKLF H[DPLQDWLRQ VWDQG CAUTIONS %H FDUHIXO QRW WR KDYH \RXU ¿QJHUV FDXJKW ZKHQ LQVHUWLQJ UHPRYLQJ
[2] Bed type Center mark CAUTIONS :KHQ LQVHUWLQJ WKH ÀDW SDQHO VHQVRU WR WKH UDGLRJUDSKLF H[DPLQDWLRQ VWDQG direct the exposure plane upwards. 1 3XOO RXW WKH WUD\ E\ XVLQJ WKH KDQGOH :KHQ VHWWLQJ WKH ÀDW SDQHO VHQVRU horizontally, position the connector as VKRZQ LQ WKH ¿JXUH EHORZ 3 Tray Basic Operation 2 3XOO WKH FDVVHWWH VWRSSHU DQG VHW WKH ÀDW SDQHO VHQVRU VR WKDW LWV FHQWHU PDUN LV DOLJQHG ZLWK WKH FHQWHU RI WKH VWRSSHU 3RVLWLRQ WKH FRQQHFWRU RI WKH ÀDW SDQHO VHQVRU DV VKRZQ LQ WKH ¿
&KDUJLQJ WKH %DWWHU\ 3DFN 2SWLRQDO IRU WKH )ODW 3DQHO Sensor (DR-ID 601SE) When used in wireless communication mode, charge the battery pack using the battery charger (optional). When the battery pack is fully charged, exposures for a maximum of approximately 200 images can be performed. However, the number varies depending on the usage conditions. The capacity of the battery is displayed on the READY status lamp and in the Console display.
,QVWDOOLQJ 5HPRYLQJ WKH %DWWHU\ 3DFN 2SWLRQDO IRU WKH Flat Panel Sensor (DR-ID 601SE) )ROORZ WKH SURFHGXUH EHORZ WR LQVWDOO UHPRYH WKH EDWWHU\ SDFN IRU WKH ÀDW SDQHO VHQVRU '5 ,' 601SE). 1 Remove the battery cover. 3ODFH WKH ÀDW SDQHO VHQVRU ZLWK WKH EDFN VLGH IDFLQJ upward and then press the right-hand and left-hand slide locks to remove the battery cover. Battery cover 2 ,QVWDOO WKH EDWWHU\ SDFN $OLJQ WKH EDWWHU\ SDFN ZLWK WKH ÀDW SDQHO VHQVRU '5 ID 601SE) by using the guide marks.
6WDUWLQJ 8S DQG 6KXWWLQJ 'RZQ WKH System This section explains how to start up and shut down the system. To start up the system, operations are required on the FDR D-EVO main unit and on the Console. To shut down the entire system, operations are required only on the Console. 6WDUWLQJ 8S WKH 6\VWHP 1 Press the ON side of the main switch of the power supply unit, if its power status LED is not lit.
6KXWWLQJ 'RZQ WKH 6\VWHP 1 &RQ¿UP WKDW WKH HTXLSPHQW LV QRW UXQQLQJ 7RXFK WKH EXWWRQ DW WKH XSSHU ULJKW RI WKH button from the displayed menu. Touch the Console display, and then the EXWWRQ LQ WKH GLVSOD\HG FRQ¿UPDWLRQ ZLQGRZ The Console will shut down in a few minutes. The control cabinet will also turn off automatically. 1 3 Basic Operation 2 3 2 Turn off the display as necessary.
3.3 Routine Operations FDR D-EVO routine operations can be broadly divided into the following three steps. Step 1 Entering the Patient Information (See page 3-10.) Step 2 Selecting the Anatomical Region and Exposure/Study Menu (See page 3-11.) Step 3 X-ray Exposure (See page 3-13.) 3 HINT Basic Operation Operations that are actually performed on the FDR D-EVO are only those described in “ Step 3 X-ray Exposure”. Other operations are performed on the Console.
Step 1 1 (QWHULQJ WKH 3DWLHQW ,QIRUPDWLRQ The Study Information Input Screen below is displayed on the Console display immediately after startup. Enter patient information items appropriately, and then touch the button. Not all the items of patient information need to be input. Input any one of the items in order to proceed to the next operation. :KHQ WKH RSWLRQDO FDUG UHDGHU LV SURYLGHG SDWLHQW LQIRUPDWLRQ FDQ EH LQSXW E\ UHDGLQJ IURP D PDJQHWLF FDUG List tab Displays various lists.
Step 2 1 6HOHFWLQJ WKH $QDWRPLFDO 5HJLRQ DQG ([SRVXUH 6WXG\ Menu The Exposure Menu Selection Screen is displayed. 7RXFK DQ DQDWRPLFDO UHJLRQ WR GLVSOD\ WKH GHVLUHG H[SRVXUH PHQX DQG WKHQ WRXFK DQ H[SRVXUH menu (more than one menu can be selected).
3 The Study Screen is then displayed. 2SHUDWH DSSURSULDWHO\ DFFRUGLQJ WR GLVSOD\ PRGH RQH LPDJH GLVSOD\ VL[ LPDJH GLVSOD\ RQ WKH Study Screen. . 7KH PRGH FDQ EH VZLWFKHG DOWHUQDWHO\ E\ WRXFKLQJ One-image display mode 3 Basic Operation Six-image display mode 3-12 FDR D-EVO Operation Manual 897N101473E
Step 3 X-ray Exposure When settings on the Console have been completed, you can perform an exposure. CAUTIONS Ɣ 0DNH VXUH WR LGHQWLI\ D SDWLHQW DJDLQVW WKH QDPH RU ELUWK GDWH DQG WKHQ KDYH KLP KHU WDNH D SURSHU SRVLWLRQLQJ IRU H[SRVXUH Ɣ 0DNH VXUH WR FRQ¿UP WKH H[SRVXUH PHQX WR EH XVHG DQG WKHQ KDYH D SDWLHQW WDNH D SURSHU SRVLWLRQLQJ IRU H[SRVXUH Ɣ :KHQ PXOWLSOH SDQHOV DUH XVHG PDNH VXUH WKDW WKH 5($'< ODPS DPRQJ WKH VWDWXV ODPSV RI WKH ÀDW SDQHO VHQVRU LV OLW LQ RUGHU WR FRQ¿UP WKDW LW LV WK
> @ ; UD\ H[SRVXUH ,PDJH GLVSOD\LQJ 0DNH VXUH WKDW H[SRVXUH LV SRVVLEOH RQ WKH &RQVROH DQG WKHQ SHUIRUP ; UD\ H[SRVXUH Perform exposures having the patient hold tight the grip handles if necessary. Exposed images are transferred to the Console.
Touch the button at the lower right to complete the study. To prepare for exposures of the next patient, repeat Step 1 through Step 3 . Touch this button. The registration of the next new patient should be processed after more than 2 seconds.
> @ )RU H[SRVXUHV RI WKH QH[W SDWLHQW XVLQJ WKH VDPH PHQXV 1 7R PDNH H[SRVXUHV RI WKH QH[W SDWLHQW XVLQJ WKH VDPH PHQXV WRXFK WKH button. left instead of the button at the upper Touch this button. 2 The Patient Information Input Screen below appears. Touch DW WKH ORZHU ULJKW WR FOHDU RII SDWLHQW LQIRUPDWLRQ XVHG IRU WKH SUHYLRXV SDWLHQW DQG then input new patient information items in the same screen. 3 Basic Operation Touch this button.
Chapter 4 7URXEOHVKRRWLQJ 4.1 :KHQ D 0HVVDJH $SSHDUV RQ WKH &RQVROH This section describes the warning dialog box and error messages. If an error which cannot be handled or the same error recurs frequently, contact a FUJIFILM dealer. If an error of unknown cause occurs, do not continue the operation and contact a FUJIFILM dealer. > @ ,I D ZDUQLQJ GLDORJ ER[ DSSHDUV If a communication error or an unexpected error has occurred, a warning dialog box pops up on the screen.
[3] If an error occurs on the Console If an error occurs on the Console, an error message box is displayed on the screen. In such a case, check error details and select [OK] in the box, and then take an appropriate action. [4] If an error occurs on an output destination device If an error occurs on an output destination device, In such a case, operate as follows. Select . An error display box is displayed.
4.2 How to Cope with an Error... > @ :KHQ WKH V\VWHP KDQJV XS If an inappropriate processing is performed while this equipment is operating, the screen may freeze and the system may hang up (processing disabled). In that case, shut down the equipment forcibly according to the following procedure, and then restart it. ,I WKH VFUHHQ IUHH]HV DQG D KDQJ XS RFFXUV UHPRYH WKH NH\ERDUG DQG PRXVH DQG UHFRQQHFW them. If this operation does not solve the problem, restart the Console.
> @ :KHQ WKH &RQVROH LV WXUQHG RII GXH WR DQ HOHFWULFDO RXWDJH When the Console is turned off due to an electrical outage, etc., take the following actions according the condition when the power comes back on. Ŷ ,I WKH SRZHU FRPHV EDFN RQ VRRQ DIWHU DQ HOHFWULFDO RXWDJH Wait until the Console restarts. When the Console has restarted, shut down the Console by following the normal procedure. For details of system shutdown, see the “DR-ID 300CL Operation Manual”.
Chapter 5 Daily Inspection and Maintenance 5.1 Daily User Inspection and Maintenance During maintenance and inspection, strictly observe precautions contained in “Chapter 1 For Safe Operation” in this manual for you to use the FDR D-EVO under best conditions. 5.1.1 Daily Inspection (DR-ID 600) Inspection Before Use 0DNH VXUH WKDW WKH HTXLSPHQW VWDUWV XS QRUPDOO\ 0DNH VXUH WKDW WKH HTXLSPHQW FRPPXQLFDWHV ZLWK FRQQHFWHG GHYLFHV QRUPDOO\ 0DNH VXUH WKDW WKH WLPH GLVSOD\HG LV FRUUHFW See “3.
5.1.2 Periodical Inspection Inspection Every Three Months Using a vacuum cleaner, remove any dirt or dust accumulated in each unit of the equipment once every three months. Clean then with a slightly moistened soft cloth and wipe off any moisture with a dry cloth. See “2.2 Unit Names and the Functions” (page 2-3). Ŷ DR-ID 600 DR-ID 600PU NO. Unit NO. 1 Flat panel sensor 4 Remote switch (optional) 2 Unit Power supply unit NO.
Appendix A Specifications A.1 Specifications 6SHFL¿FDWLRQV RI WKH )'5 ' (92 DUH VKRZQ EHORZ $ 3URFHVVLQJ &DSDFLW\ '5 ,' Ŷ 5RXWLQH SURFHVVLQJ ZKHQ WKH WZR LPDJH RXWSXW IRUPDW LV XVHG LQ standard mode) (1) Exposure interval The exposure interval of the FDR D-EVO is at least 8 seconds. However, the interval varies depending on the region, the load to network communication, etc.
[Fig. A.
$ 5HGXFHG (TXLYDOHQW '5 ,' 3HDN UHGXFHG HTXLYDOHQW RQ WKH IURQW SDQHO RI WKH ÀDW SDQHO VHQVRU PP$O A.1.4 Power Supply Conditions Ŷ DR-ID 600PU 5DWHG YROWDJH 9 a ,QSXW FXUUHQW $ )UHTXHQF\ +] Ŷ DR-ID 600MC* 5DWHG YROWDJH 9 a ,QSXW FXUUHQW $ )UHTXHQF\ +] * Since the DR-ID 600MC is general-purpose electrical equipment, the electric rating above is an example. A.1.
$ ([WHUQDO 9LHZ DQG :HLJKW The external view and weight of the FDR D-EVO are shown below. 6SHFL¿FDWLRQV GLPHQVLRQV DQG ZHLJKW DUH VXEMHFW WR FKDQJH IRU LPSURYHPHQW ZLWKRXW SULRU notice. A.2.1 DR-ID 600 Ŷ DR-ID 600PU Width (mm) Depth (mm) +HLJKW PP :HLJKW NJ 460 384 14 Approx. 3.1kg 460 384 14 Approx. 2.8kg 120 350 (385) 350 Approx. 7.
16.75 432.0 10.75 Effective area 16.45 345.6 21.45 7KH HIIHFWLYH DUHD RI WKH ÀDW SDQHO VHQVRU LV DV VKRZQ LQ WKH ¿JXUH EHORZ Ŷ DR-ID 600MC Width (mm) 114 Control cabinet Depth (mm) 353 +HLJKW PP 399 :HLJKW NJ Approx. 8.
Ŷ %DWWHU\ FKDUJHU Battery charger Width (mm) Depth (mm) +HLJKW PP :HLJKW NJ 120.2 219.8 136.2 Approx. xx kg 8QLW PP 219.8 136.2 120.2 Battery charger Ŷ DR-ID 300CL For the external view and weight of the DR-ID 300CL, see the “DR-ID 300CL Operation Manual”.
Appendix Z Precautions for Exposure Z1. Precautions for Exposure in AUTO MODE In AUTO MODE, stable image output can be obtained by means of the following. 5DGLDWLRQ ¿HOG (2) EDR image data analysis (3) Detailed depiction of the cervical region However, problems may arise due to differences in the multiple diaphragms or scattered rays of the X-ray equipment. For such problems, contact a FUJIFILM dealer and use other recording modes, such as SEMI-AUTO MODE or FIX MODE. Z.1.
= 'HSLFWLRQ RI WKH &HUYLFDO 5HJLRQ 1 7KH UDGLDWLRQ ¿HOG PXVW QRW LQFOXGH WKH ZKROH KHDG %H VXUH WR VHFXUH WUDQVSDUHQW SRUWLRQV RQ ERWK sides of the neck. 8VH WKH ³+HDG´ PHQX WR LQFOXGH WKH ZKROH KHDG LQ WKH UDGLDWLRQ ¿HOG 2 )RU H[SRVXUH RI WKH SKDU\Q[ RU ODU\Q[ EH VXUH WKDW WKH QHFN FRPHV WR WKH FHQWHU RI WKH UDGLDWLRQ ¿HOG so that the frontal and lateral orientations can be recognized appropriately.
= ('5 ,PDJH 'DWD $QDO\VLV 1 Image unevenness appearing when the grid used in exposure is not positioned correctly in terms of the bulb, when there are shadows from clothing, or when X-ray radiation of the X-ray exposure area is uneven is a problem that arises during EDR image data analysis, which cause unstable density on the image. Avoid such unevenness in the X-ray exposure area as far as possible. 2 If the target includes such materials as gypsum, denture, etc.
Z.2 Precautions for Exposure in SEMIAUTO MODE These precautions are common to Semi I, II, III and III(**). 1 Position the portion you need to display often in the center areas (10cm × 10cm (Semi I), 7cm × 7cm (Semi II), 5cm × 5cm (Semi III)) of the images trimmed by the DR system. Position the portion you need to display often in each of the 5cm × 5cm center areas of the half-split images (both upper and lower halves and right and left halves) and quarter-split image trimmed by the DR system.
Z.3 Precautions for Exposure in SEMI-X MODE The user will select one of the nine areas of the image trimmed by the DR system, on which SEMIAUTO MODE applies. (See the illustration below.) The same precautions as for SEMI-AUTO MODE apply.
Z.4 Precautions for Exposure in FIX MODE $V UHDGLQJ FRQGLWLRQV DUH ¿[HG H[SRVXUH FRQGLWLRQV PXVW EH FRQWUROOHG LQ WKH VDPH ZD\ DV IRU conventional X-ray exposure. The reading conditions (sensitivity and latitude) have been preset according to the relevant menu in FIX MODE. Select the exposure conditions which correspond to that menu accordingly.
Z.5 Other Precautions Z.5.1 Precautions for Exposure of a Subject in Relatively /DUJH &RQWUDVW 1 Exposures using a contrast medium may cause artifacts around it. 2 When exposing a subject with any metal objects implanted, artifacts may appear around them. 3 For exposures with objects of large X-ray absorption, such as lead characters and metals for measurement, artifacts may appear around them. Place such objects outside a subject. Z.5.2 Precautions for DR System *HQHUDOO\ ZKHQ SHUIRUPLQJ D KLJK VHQVLWLYL
= ,PDJHV 2XWSXW :KHQ WKH ; UD\ 6KRW 6ZLWFK LV 2SHUDWHG Incorrectly In case that you press the X-ray shot switch only momentarily after selecting exposure menus, VXI¿FLHQW ; UD\ GRVH PD\ QRW EH DFKLHYHG 7KH RXWSXW LPDJH FRQWDLQV LPDJH ODJV RI WKH SUHYLRXV exposure occasionally. If this happens, select exposure menus again, and then make an exposure.
Appendix O Use of Optional Items O.1 Optional Items Name Remote switch Description $ VZLWFK FDEOH XVHG IRU WHPSRUDULO\ GLVFRQQHFWLQJ WKH SRZHU WR WKH ÀDW SDQHO sensor in order to connect/disconnect its connector while the system is in operation. Up to two remote switches can be connected. Using this switch reduces the time required for normal insertion/removal procedure. For the external view, see “O.2.1 Remote Switch” (page O-2).
2 8VLQJ WKH 5HPRWH 6ZLWFK O.2.1 Remote Switch Operation button Remote switch fixture* (with double-sided tape) Remote switch * 7KLV PHWDO ¿[WXUH LV XVHG ZKHQ WKH UHPRWH VZLWFK FDQQRW EH DWWDFKHG WR D ZDOO HWF ZLWK WKH PDJQHW RQ WKH EDFN 7KH UHPRWH VZLWFK ¿[WXUH LV DWWDFKHG WR D ZDOO HWF ZLWK GRXEOH VLGHG WDSH O.2.
2 8VLQJ WKH 6( 6WRUDJH &DVH SE storage case :KHQ VWRULQJ WKH ÀDW SDQHO VHQVRU LQ WKH 6( VWRUDJH FDVH SODFH LW ZLWK WKH H[SRVXUH SODQH GRZQ 1RWH DOVR WKDW WKH VWRUDJH PHWKRG YDULHV GHSHQGLQJ RQ WKH GLUHFWLRQ RI WKH ÀDW SDQHO VHQVRU connector. For details, see the illustrations below.
2 8VLQJ WKH '$3 &RQQHFWRU &DEOH The DAP connector cable is used for connecting a dose-area product (DAP) meter*1 to the power supply unit. This cable is connected to a dose-area product meter via an RS232C insulator*2. To connect a DAP meter, contact a FUJIFILM dealer. Power supply unit RS232C insulator DAP connector cable $ '$3 PHWHU RI ZKLFK )8-,),/0 &RUSRUDWLRQ KDV FRQ¿UPHG WKH RSHUDWLRQDO SHUIRUPDQFH LV 9DFX'$3 Standard of VacuTec Meßtechnik GmbH.
2 8VLQJ WKH 5HWDLQLQJ %UDFNHW IRU 03 Cap Bolt Fixture Anchor &RQWDFW D )8-,),/0 GHDOHU IRU LQVWDOODWLRQ RI WKH 5HWDLQLQJ EUDFNHW IRU 03 Appendix O Use of Optional Items FDR D-EVO Operation Manual 897N101473E O-5
Appendix O Use of Optional Items O-6 FDR D-EVO Operation Manual 897N101473E
Maintenance and Inspection 0DLQWHQDQFH DQG ,QVSHFWLRQ ,WHPV $VVLJQHG WR 6SHFL¿HG 'HDOHU )RU SHULRGLFDO LQVSHFWLRQ RI WKH HTXLSPHQW DQG QHFHVVDU\ DUUDQJHPHQWV FRQVXOW RXU RI¿FLDO GHDOHU or local representative.
This device complies with Part 15 of FCC Rules and RSS-Gen of IC Rules. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device. FCC WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FUJIFILM MEDICAL SYSTEMS U.S.A., INC.