Instruction for Use lnfrared Thermometer (Contact Type) FT-F11-BT,FT-F21-BT, FT-F12-BT, FT-F22-BT FT-F11, FT-F21, FT-F12, FT-F22 UO8080, UO8080E - 1 -
INFRARED THERMOMETER (FT-F11-BT, FT-F21-BT, FT-F12-BT, FT-F22-BT; FT-F11, FT-F21, FT-F12, FT-F22, UO8080, UO8080E) Operating Instruction Please read carefully before use. DESCRIPTION 1. Table of Contents 1. Product Listing 2. Product Overview 3. Outline Drawing 4. The Definition of Symbols 5. Measuring 6. Battery Voltage Display & Replacement 7. Operation Precautions 8. Precaution for Measuring Temperature 9. Product Specification 10. Common question concerning forehead temperature 2.
FT-F12-BT &FT-F12 FT-F22-BT&FT-F22 4.The Definition of Symbols Reading Display Ear Measuring mode (Suitable for FT-F11, FT-F12 & FT-F21, FT-F22 FT-F11-BT, FT-F21-BT; FT-F12-BT, T-F22-BT; UO8080) Forehead Measuring mode (Suitable for FT-F21,FT-F22 & FT-F21-BT FT-F22-BT, UO8080E) Celsius Scale Fahrenheit Scale Low Battery Last Memorized Temperature Display 5. Measuring 1) Ear Measuring Mode (Figure 5.
temperature unit“ ” or “ ” blink it’s ready to measure, please see on( Figure 5.4) ●Insert the IR Thermometer probe into the ear canal as on the following (Figure 5.1); Pull the ear slightly back ward to straighten the ear canal. Then insert the probe into the ear as far as it goes. Be sure the probe fully seals the ear canal. Hold this position until the measurement is completed.
3) “ ” and“ ”adjust (Suitable for FT-F11,FT-F21,FT-F11-BT,FT-F21-BT, UO8080, UO8080E) ● On power off condition, press the “SCAN” button key about 5 seconds until the displayed screen appears “- - -” and “ ” or “ ” temperature unit blinks . In this condition, press the “SCAN” button key again to adjust “ ””or “ ” and then it is set up ready for use.
7. Operation Precautions 1). Please insert the battery into the bracket when do you use the IR Thermometer on first time. 2). Please keep the probe clean after you used the IR Thermometer. 3). Please keep the IR Thermometer dry and never immerse it in water or any liquid. 4). Do not put the IR Thermometer under high temperature environment on long time and keep away from sunlight, dust and dirt. 5). Do not put the IR Thermometer with keen-edged goods together. 6).
Description Meaning Measuring temperature over 43.0℃/109.4℉ Measuring temperature lower than 34.0℃/93.2℉ Environment temperature high than working temperature.10.0℃- 40.0℃(50.0℉- 104.0℉) 9. Specifications Model No. FT-F11, FT-F21, FT-F12, FT-F22; FT-F11-BT, FT-F21-BT; FT-F12-BT, FT-F22-BT; UO8080, UO8080E Measuring Range Body 34.0℃-43.0℃( 93.2℉-109.
Mode of operation Size (body) Weight(including battery) Continuous operation L145*W35*H40mm (Suitable for FT-F11, FT-F21 FT-F11-BT FT-F21-BT) L120*W44*H60mm (Suitable for FT-F12, FT-F22 FT-F12-BT FT-F22-BT) L132*W40.3*H65mm (Suitable for UO8080, UO8080E) 78g(FT-F11,FT-F11-BT),80g(FT-F21,FT-F21-BT), 48g(FT-F12,FT-F12-BT;FT-F22,FT-F22-BT) -infrared thermometer -batteries 3V (Optional) Contents -Storage case (Optional) -Instruction Manual Bluetooth Version Bluetooth Modulation Type Bluetooth 4.
10. Common questions concerning forehead temperature: 1). What is the forehead temperature? Forehead temperature is the same temperature as the arterial blood supply under the skin. It is the best determinate of body temperature, and unaffected by the artificial errors and time delays of oral and rectal methods. 2). How to take forehead temperature properly? Gently touch the probe to center of forehead .Make sure remove anything covering the area to be measured (hair .hat .wig .and bandages).
descriptions, calibration instructions to assist to service personnel in parts repair. Notes: If you have any problems with this device, such as setting up, maintaining or using, please contact with service personnel of FUDAKANG INDUSTRIAL CO.,LTD. Don’t open or repair the device by yourself. Please report to FUDAKANG INDUSTRIAL CO.,LTD if any unexpected operation or events occur. After drop/ shock…,that may cause changes in the performance , please contact with service personnel of FUDAKANG INDUSTRIAL CO.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
guidance Electrostatic discharge (ESD) ±6 kV contact ±6 kV contact Floors should be wood, concrete or ±8 kV air ±8 kV air ceramic tile. If floor are covered with IEC 61000-4-2 synthetic material, the relative humidity should be at least 30%. If ESD interfere with the operation of equipment ,counter measurements such as wrist strap, grounding shall be considered.
Portable and mobile RF communications equipment should be used no closer to any part of the [EQUIPMENT or SYSTEM], including cables, than the recommended separation distance Conducted RF 3 Vrms IEC 61000-4-6 150 kHz to 80 MHz Not applicable Radiated RF 3 V/m 3 V/m IEC 61000-4-3 80 MHz to 2.5 GHz calculated from the equation applicable to the frequency of the transmitter. Recommended separation distance d = 1.167 P d = 1.167 P 80 MHz to 800 MHz d = 2.333 P 800 MHz to 2.
Recommended separation distances between portable and mobile RF communications equipment and the [EQUIPMENT or SYSTEM]. The [EQUIPMENT or SYSTEM] is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled.
Symbol for ‘CE” Symbol for “electrical and electronic equipment” Symbol for “TYPE BF APPLIED PART” Symbol for “Follow operating instructions” IP22 Symbol for “the IP classification” Symbol for “ RF transmitters” Manufacturer: FUDAKANG INDUSTRIAL CO.,LTD Address :No.8 Yinghe Road, Yuanjiangyuan Management Zone, Changping Town, Dongguan, Guangdong China. Tel: 86-769-81098181 Fax: 86-769-81098187 Website: www.fudakang.com Software Version: V3.0 Manual Version: V2.