Instruction for Use Digital Thermometer BT-A41CN-BT
Operating Instruction INTENDED USE The Digital Thermometers, Models BT-A41CN-BT, are intended for the measurement and monitoring of human body temperature by doctor or consumers in the hospital or home. It is used alone for human beings at all ages. FEATURES 1. LCD displays the measured temperature. 2. With memory function the last measured temperature is shown on LCD. 3. With beeper to alarm the peak temperature. 4. Auto self-test and power auto shut-off. 5.
Display type Memory Service life Alarm Working Environment Storage Environment Battery life Power consumption Applied part type: IP classification Mode of operation: Readout time Liquid Crystal Display The last measured temperature is shown on LCD Display Expected to be 5 years Approx.10 seconds of Bi voice while peak temperature is stable (for no voice model) Temperature: 5~40°C Humidity: 15% to 85%RH 86Kpa to 106 Kpa Temperature: -20~55°C Humidity: ≤85%RH 86Kpa to 106 Kpa Approx.
HOW TO USE 1. Press On/Off button then LCD displays 188.8℉M(188.8℃M)for 2 seconds. Keep pressing then displays last measurement, and releasing 98.6℉(37.0℃)for 1 second with ℉or℃ flashing respectively. 2. If ambient temperature is higher than 111.2℉(44.0℃),LCD displays H ℉(H℃)and lower than 89.6℉(32.0℃) then displays L0℉(L0℃). 3. Disinfect the probe with alcohol then place the probe under/in: 3.1 Oral use: Place the probe under tongue and close the mouth about 1minute till temperature is stable.
★ Start to measure according to the normal infrared thermometer operation method. ★ After measuring the result will be displayed on LCD and be sent to the blue tooth receiving device such as mobile phone. The additional function of blue tooth infrared thermometer is to transmit the testing result to the APK in the receiving device via blue tooth technology.
Guidance and manufacture’s declaration – electromagnetic emission The BT-A41CN-BT is intended for use in the electromagnetic environment specified below. The customer of the user of the BT-A41CN-BT should assure that it is used in such an environment. Emission test Compliance Electromagnetic environment – guidance Group 1 The BT-A41CN-BT use RF energy only for its internal function. Therefore, its RF emissions are very low and are not likely to cause any interference in nearby electronic equipment.
Guidance and manufacture’s declaration – electromagnetic immunity The BT-A41CN-BT is intended for use in the electromagnetic environment specified below. The customer or the user of the BT-A41CN-BT should assure that it is used in such an environment.
operation. If abnormal performance is observed, additional measures may be necessary, such as re-orienting or relocating the BT-A41CN-BT. b Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3 V/m. Recommended separation distances between portable and mobile RF communications equipment and the BT-A41CN-BT . The BT-A41CN-BT is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled.
PRECAUTIONS 1. Do not bite、 bend、drop or take apart the thermometer. 2. Keep the device out of the reach of children/pets to avoid inhalation or swallowing of small parts. 3. Do not expose it to direct sunlight、high temperature and moisture 4. Not intended to be sterilized. Prevent saliva or cleaning solution from penetrating the display window. 5. Clean the thermometer after of before use with soft cloth and cleaning solution listed below and store in the plastic case.
Note: Any solution, dilution and method other than mentioned above might cause reliability problems with the thermometer. The patient is an intended operator. The patient can measure, change batteries under normal circumstances and maintain the device and its accessories according to the user manual. LIMITED WARRANTY This thermometer is guaranteed for 5 years from the purchasing date under normal use .The warranty does not cover the damage of improper use or the battery running out.
Symbol for “ RF transmitters” IP22 Symbol for “the IP classification” Symbol for Bluetooth Manufacturer :FUDAKANG INDUSTRIAL Co., Ltd 301,3rd Floor, Block 1,No.60 Shangshuxia Road ,Changping Town, Dongguan City,Guangdong Province,China. EC Representative FANTRONIC COMPOSANTS Rue Jacques Laurent ZA – Sud – Est - BP 11 85150 LA MOTHE ACHARD – FRANCE Tel: +33 2 51 08 89 20 Soft ware Version: 1.3 Manual Version: 2.