X9D Plus 2019 X9D Plus SE 2019 Manual

FrSky Electronic Co., Ltd. www.frsky-rc.com Contact us: [e-mail]
Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: [e-mail]
FrSky Electronic Co., Ltd. www.frsky-rc.com Contact us: [e-mail]
Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: [e-mail]
Navigate the Menu
To navigate the menus, Taranis X9D Plus 2019/Taranis X9D Plus SE 2019 has the following elements:
● Scroll Button
● MENU Button
● PAGE Button
● EXIT Button
FrSky Electronic Co., Ltd. www.frsky-rc.com Contact us: [e-mail]
Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: [e-mail]
Due to unforeseen changes in production, the information contained in this manual is subject to change without notice. Pay special
attention to safety where indicated by the following marks:
Meanings of Special Markings
DANGER - procedures which may lead to dangerous conditions and cause death/serious injury if not carried out properly.
WARNING - Procedures which may lead to a dangerous condition or cause serious injury and even death to the user if not carried
out properly or procedures where the probability of superficial injury or physical damage is high.
CAUTION - Procedures where the possibility of serious injury to the user is small, but there is a danger of injury or physical damage,
if not carried out properly.
NOTE – Steps, Tips or information
WARNING - Always keep electrical components away from children.
Introduction
Warnings for Battery
Do not remove the battery from the
X9D Plus 2019/X9D Plus SE 2019 transmitter while the voltage warning is
blinking as this could cause internal settings and memories to be destroyed.
Do not use the transmitter if a “Backup Error” warning occurs.
FrSky 2.4GHz ACCESS Taranis X9D Plus 2019/Taranis X9D Plus SE 2019 Manual
FrSky 2.4GHz ACCESS Taranis X9D Plus 2019/Taranis X9D Plus SE 2019 Manual
FrSky 2.4GHz ACCESS Taranis X9D Plus 2019/Taranis X9D Plus SE 2019 Manual
FrSky Electronic Co., Ltd. www.frsky-rc.com Contact us: [e-mail]
Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: [e-mail]
Long press the Scroll Button there will generate a pop-up where the user can reset timer, reset telemetry values,
reset all above, jump to the tele setup page.
Quick select options
FrSky 2.4GHz ACCESS Taranis X9D Plus 2019/Taranis X9D Plus SE 2019 Manual
TM
Model Setup for Taranis X9D Plus 2019/Taranis X9D Plus SE 2019 Internal RF Module
Enter the MODEL SETUP menu.
Step 1: Set the Mode for Taranis X9D Plus 2019/Taranis X9D Plus SE 2019 Internal RF.
Go to the MODEL SETUP menu, and select the Internal RF, select [Mode] [ACCESS].
Step 2: Set the Channel Range
The Internal RF module of Taranis X9D Plus 2019/Taranis X9D Plus SE 2019 supports up to 24 channels. The channel range is
configurable,and needs to be confirmed before use.
Step 3: Set the Receiver Number
When you create a new model, the system will assign you a receiver number automatically, but this can be easily changed. The range
of the receiver number is 00-63, with the default number being 01 (use 00 is not recommended). Once the receiver is set to desired
number and is bound to the Taranis X9D Plus 2019/Taranis X9D Plus SE 2019, the bind procedure will not need to be repeated unless
the receiver number is changed. In this case, either set the receiver number to the previous one or repeat the bind procedure.
Step 4: Registration
In ACCESS, select the Module [Register] into Registration status. Then Press the F/S button and power on your receiver, and select
the “RX Name XX” and [ENTER] to complete the Registration process then power down the receiver.
Note:
If two or three receivers are used at the same time, the UID should be set to different values.
Step 5: Automatic binding (Smart Match )
Move the cursor to Receiver1[Bind],and select it , power your receiver, select the RX, and complete the process, the system will confirm
"Bind successful". (You do not need to press the "F/S" button in ACCESS to Bind. Refer to the receivers manual for details)
Taranis X9D Plus 2019/Taranis X9D Plus SE 2019 supports OpenTX system
Scroll Button
To navigate menus or widgets, roll the button to left or right as navigation.
MENU Button
To go to the [Model] menu, press the button.
To go to the [RADIO SETUP] menu, press the button, and hold for one second.
PAGE Button
To go to switch the page, press the button.
To go to the [Telemetry] menu, press the button, and hold for one second.
EXIT Button
To exit current page or operation widgets.
System item Currently selected page
Where am I in the menu tree
Overview of the menu tree
Press the MENU button.and hold for one second.Press the MENU button.
Press the PAGE button.and hold for one second.
To change the data in other
items, firstly roll Scroll
Button to the left or right
until the cursor stays at the
needed item.
Secondly, press Scroll
Button and roll the button
to the left or right.
To go to the next page, move the
cursor to the item, then Scroll Button
roll to the left or right.
The cursor will firstly stay at the item
which indicates the current page.
The FrSky Taranis X9D Plus 2019 is a re-designed version with additions like an additional momentary button placed on the top left
shoulder making it ergonomically friendly for DLG pilots to activate launch mode, and features a program scroll wheel making it even
easier to navigate the menus. The upgraded MCU is used in conjunction with a re-designed mainboard that further increases the
computing capability and increases the data storage. The upgrades not only improve the running of LUA scripts, it also optimizes
overall performance like voice speech outputs.
The 2019 version uses the latest ACCESS communication protocol, it boasts 24 channels with a faster baud rate and lower latency
with a high-speed module digital interface. Along with the new spectrum analysis function added to the OpenTX firmware, it is now
possible to check the airwaves for RF noise. This version will give you a further improved experience based on the classic Taranis
remote control. Additionally, tons of extra upcoming features that ACCESS brings will make this an ideal transmitter for any skill level.
The SE 2019 version is installed with the upgraded switches and M9 hall sensor gimbals and features the addition of a PARA wireless
trainer function which makes them compatible with the FrSky Free Link App and AirLink S.
Specifications
● Model name: Taranis X9D Plus 2019/Taranis X9D Plus SE 2019
● Dimension: 200*194*110 (L*W*H)
● Weight: Taranis X9D Plus 2019: 670g (without battery)
Taranis X9D Plus SE 2019: 700g (without battery)
● Operating Current: 130mA@8.2V (Typ)
● Backlight LCD resolution: 212*64
● Model Memories: 60 models (Extenable by Micro SD card)
● Number of channels: 24 channels
● Operating Voltage Range: DC 6.5~8.4V
● Opertaing Temperature: -10℃~60℃ (14℉~140℉)
● Smart Port, Micro SD card slot and USB Port
● OpenTX system
Overview
Switch
● SA: 3 positions; Short Lever
● SB: 3 positions; Long Lever
● SC: 3 positions; Long Lever
● SD: 3 positions; Short Lever
● SE: 3 positions; Short Lever
● SF: 2 positions; Long Lever
● SG: 3 positions; Short Lever
● SH: 2 positions; Momentary, Long lever
● S1&S2: Knob, Switch
● SI: Tact switch, Momentary
1. Micro SD card is not provided with shipment.
2. USB port is for upgrading, reading/writing
Micro SD cards and internal memory of radio
contents and charging (Includes USB cable in
packge but without the adapter).
3. Smart Port is for firmware upgrade for all
FrSky S.Port devices.
4. Battery compartment size: 100*30*26.5mm
(L*W*H）
SI
Battery Port
Smart Port
Micro SD Card Port
Scroll button
Power Switch
Caution:
Only 2S Li-battery without protective circuit can be applied to balance charging system, and please
do not charge any other types of battery.
Mini USB Port
Features
● Classic Taranis form factor design
● High-speed module digital interface
● Easy Launch Momentary Button
● Installed with ACCESS protocol
● Supports spectrum analyzer function
● SWR indicator
● Haptic vibration alerts and voice speech outputs
Operating System OpenTX OpenTX
Communication Protocol ACCST D16 /ACCESS ACCST D16 /ACCESS
Program Navigation Button √ √
Easy Launch Momentary Button √ √
2S Li-Battery Charging System* √ √
G9D Potentiometer Gimbal √
M9 Hall Sensor Gimbal √
Upgraded Switches √
Wired Training System √ √
PARA wireless training function
● PARA High-speed training system with a lower latency
● Compatible with FrSky Free Link App and AirLink S
via mobile devices
Comparison List
Taranis X9D Plus 2019 Taranis X9D Plus SE 2019
√
About USB 2S Li-battery balance charging :
The Green Power indicator LED state:
Led on: charging Led off: charge end Led flash: charge fault
Note:
1. Charge the battery with the USB adapter (Voltage:5V+0.2V Current:＞2.0A) when you use the USB
charging function.
2. The lower the initial charging voltage, the better the charging effect is when the voltage difference
between the two cells exceed 50 mV.
Using the following type of battery:
LiFePO battery is not supported.
Battery compartment size: 100*30*26.5mm（L*W*H) Recommended battery pack size: ≤80*30*24mm(L*W*H)
*USB adapter Voltage: 5V+0.2V Current:＞2.0A
4
PH2.54-XH-3Y
Battery +
Battery Balance
Battery -
Olny 2S Li-Ion/Li-Po battery
without protective circuit