Wiring Diagram

NOTICE - This service data sheet is intended for use by persons having
electrical and mechanical training and a level of knowledge of these
subjects generally considered acceptable in the appliance repair trade.
The manufacturer cannot be responsible, nor assume any liability for
injury or damage of any kind arising from the use of this data sheet.
SAFE SERVICING PRACTICES
To avoid the possibility of personal injury and/or property damage, it is
important that safe servicing practices be observed. The following are
examples, but without limitation, of such practices,
1. Before servicing or moving an appliance remove power cord from
electrical outlet, trip circuit breaker to OFF, or remove fuse.
2. Never interfere with the proper installation of any safety device.
3. GROUNDING: The standard color coding for safety ground wires is
GREEN or GREEN WITH YELLOW STRIPES. Ground leads are not
to be used as current carrying conductors. It is extremely important
that the service technician reestablish all safety grounds prior to
completion of service. Failure to do so will create a potential safety
hazard.
4. Prior to returning the product to service, ensure that:
All electric connections are correct and secure.
All electrical leads are properly dressed and secured away from sharp
edges, high-temperature components, and moving parts.
All uninsulated electrical terminals, connectors, heaters, etc. are adequately
spaced away from all metal parts and panels.
All safety grounds (both internal and external) are correctly and securely
reassembled.
OVEN CALIBRATION
Set the electronic oven control for normal baking at 350°F. Obtain an average
oven temperature after a minimum of 5 cycles. Press OFF keypad to end Bake
mode.
TEMPERATURE OFFSET ADJUSTMENT
1. While in a non-cooking mode, press and hold the Bake key for 3
seconds.
2. The current calibration offset (temperature adjustment) should appear in
the temperature display.
3. Use the number keypads (0-9) to enter the desired amount of adjustment
(-35° to 35° F).
4. Press the Self clean keypad to change the sign of the adjustment to a (-)
if necessary. A positive adjustment will not display a sign.
5. Once the desired adjustment (-35° to 35° F) has been entered, press
the Start keypad to accept the change or the OFF keypad to reject the
change.
Note: Changing calibration affects all baking modes. The adjustments made
will not change the self-clean cycle temperature.
A13882501 REV A EN (1910)
SERVICE DATA SHEET
Electric Range with ES541 Electronic Oven Control
K8
K6
OVEN
LIGHT
LUMIÈRE
DU FOUR
K5
CONV
FAN
VENT. DE
CONV
K7
K9
MDL
INTERRUPT-
EUR DU
LOQUET
MOTORISÉ
DE LA
PORTE
K3
CONV
ELEMENT
ÉLÉMENT
DE CONV
K2
BAKE
CUIRE
K1
DLB
DOUBLE
BREAK EN
LIGNE
K4
BROIL
GRIL
MACS1
1
1
J2
J8
1
NEUTRAL/
NEUTRE
L1
OVEN LIGHT/LAMPE DU FOUR
CONVECTION FAN/VENTILATUER DE CONVECTION
MOTOR DOOR LATCH/INTERRUPTEUR DU LOQUET MOTORISÉ DE LA PORTE
OVEN DOOR SWITCH/INTERRUPTEUR DE PORTE
DOOR LOCK SWITCH/INTERRUPTEUR DE PORTE
TEMPERATURE PROBE/SONDE À TEMPÉRATURE
MEAT PROBE/SONDE À VIANDE
MEAT PROBE/SONDE À VIANDE
MACS2
J6
BAKE
CUIRE
J7
CONV
ELEMENT
ÉLÉMENT
DE CONV
J5
L1 IN
L1 DANS
TO USER INTERFACE BOARD/
PANNEAU D'INTERFACE DE
L'UTILISATEUR (UIB)
COMMON/COMMUNE
1
BROIL/GRIL
L1
Resistance (ohms)
1000 ± 4.0
1091 ± 5.3
1453 ± 8.9
1654 ± 10.8
1852 ± 13.5
2047 ± 15.8
2237 ± 18.5
2697 ± 24.4
Open circuit/infinite resistance
RTD SCALE
Temperature °F (°C)
32 ± 1.9 (0 ± 1.0)
75 ± 2.5 (24 ± 1.3)
250 ± 4.4 (121 ± 2.4)
350 ± 5.4 (177 ± 3.0)
450 ± 6.9 (232 ± 3.8)
550 ± 8.2 (288 ± 4.5)
650 ± 9.6 (343 ± 5.3)
900 ± 13.6 (482 ±7.5)
Probe circuit to case ground
IMPORTANT
DO NOT REMOVE THIS BAG
OR DESTROY THE CONTENTS
WIRING DIAGRAMS AND SERVICE
INFORMATION ENCLOSED
REPLACE CONTENTS IN BAG
Resistance temperature detector
ELECTRONIC OVEN CONTROL (EOC) RELAY BOARD
ELECTRONIC OVEN CONTROL CODE DESCRIPTIONS
Fault Code Likely Failure Condition/Cause Suggested corrective action
F001, F002,
F004, F005
Touch failure 1. Disconnect power, wait 30 seconds and reapply power. If fault returns upon power-up replace
the Oven User Interface board.
F003 The oven user interface board is incor-
rectly congured.
1. Replace the oven user interface board. Make sure you install the latest revision available for
this model.
F010 Oven temperature runaway: the cavity
temperature has been detected in
excess of the maximum safe operating
temperature.
1. If oven is overheating, disconnect power. Check oven temperature probe (RTD) and replace if
necessary.
2. If the oven temperature probe is good and if oven continues to overheat when power is reap-
plied, replace the oven relay board.
F011 Stuck key: a key has been detected
has pressed continuously for 30 sec-
onds or more.
1. If a key was pressed inadvertently for a long time this error code will be displayed. Make sure
there is nothing (water, utensils) in contact with the keyboard. The fault code should go away
once the key is released and the Stop key is pressed. If the F011 error comes back when a
key is pressed it means the error condition is still there. If the F011 error does not come back it
means the error condition is gone and the oven can be used.
2. If the fault code cannot be cleared, the board/springs alignment within the mechanical enclose
maybe affected. Reinstall the board within the enclosure.
3. If reinstalling the board did not x the problem replace the oven user interface board.
F012 Keyboard conguration alarm: the
oven user interface board received
from the touch micro a key code that
does not match the key map.
1. Verify the unit has the proper conguration is loaded, based on the model number and parts
catalog.
2. Replace the oven user interface board if the problem persists.
F013 Data written to non-volatile memory
has failed verication
1. Disconnect power, wait 30 seconds and reapply power. If fault returns upon power-up replace
the oven user interface.
F015 Keyboard Error 1. Disconnect power, wait 30 seconds and reapply power. If fault returns upon power-up replace
the oven user interface board.
F017 The oven user interface board is
unable to congure the touch.
1. Disconnect power to the unit, wait 30 seconds, then reapply power.
2. Verify the unit has the proper oven user interface board and conguration, based on the model
number and parts catalog.
3. If fault persists, replace the oven user interface.
F018 Oven relay board failure (wiggler) 1. Replace the oven relay board.
F019 The oven user interface board is un-
able to congure the oven relay board
1. Disconnect power to the unit, wait 30 seconds, then reapply power.
2. If fault returns, verify connection between the oven user interface board and the oven relay
board (MACS1 or MACS2 connector)
3. Verify the unit has the proper oven user interface board and oven relay board, based on the
model number and parts catalog.
4. If fault persists, replace oven user interface board.
5. If fault persists, replace the relay board.
F022 Communication failure between the
oven user interface board and the
oven relay board
1. Disconnect power, wait 30 seconds and reapply power. Check if error condition is still there.
2. Test wiring harness between oven user interface board and oven relay board (connector
MACS1 or MACS2)
3. If wiring harness is good replace oven relay board.
4. If the problem persists replace the oven user interface.
F023 Communication failure between the
oven user interface micro and the
touch micro
1. Disconnect power, wait 30 seconds and reapply power. Check if error condition is still there.
2. If the problem persists replace the oven user interface.
F025, F027 The communication between the oven
user interface and the oven relay
board cannot be initiated.
1. Disconnect power to the unit, wait 30 seconds, then reapply power.
2. If fault returns, verify connection between the oven user interface board and the oven relay
board (MACS1 or MACS2 connector).
3. Verify the unit has the proper oven user interface board and oven relay board, based on the
model number and parts catalog.
4. If fault persists, replace relay board.
5. If fault persists, replace the oven user interface board.
F028, F029 The communication between the over
user interface micro and the touch
micro cannot be initiated.
1. Disconnect power to the unit, wait 30 seconds, then reapply power.
2. Verify the unit has the proper oven user interface board and conguration, based on the model
number and parts catalog.
3. If fault persists, replace the oven user interface.
F030 Open oven temperature sensor (RTD) 1. Check probe circuit wiring for possible open or short condition.
2. Verify RTD resistance at room temperature (compare to probe resistance chart). If resistance
does not match the chart, replace the RTD probe.
3. If the problem persists replace the oven relay board.
F031 Shorted oven temperature probe
(RTD)
F033 Meat probe temperature sensor short-
ed or too hot
1. The error is triggered if the meat probe sees a temperature in excess of 392°F. Make sure the
meat probe was not used in such way that it could have seen such temperature. If the tip of the
probe is not inserted in the meat it will see the cavity temperature, which can be higher than
392°F (depending on the setpoint) and trigger the alarm.
2. When the meat probe is connected to the socket inside the oven cavity, if the meat probe is not
fully inserted into the socket it may short the contacts and cause the error. Make sure the probe
is inserted as much as it can.
3. Verify meat probe resistance at room temperature. Compare to meat probe resistance chart. If
the meat probe does not match the chart, replace it.
4. If the above steps failed to correct the problem, replace the oven relay board.

Summary of content (2 pages)