Frigidaire Professional and Electrolux 2021 Tall Twin Resource Guide Revised 2/4/2021
Trim Kits and Cutout Dimensions Revised 1/15/2021
FRIGIDAIRE PROFESSIONAL Classified as Internal
Classified as Internal
Classified as Internal
FRIGIDAIRE PROFESSIONAL Classified as Internal
Classified as Internal
Classified as Internal
ELECTROLUX Classified as Internal
Classified as Internal
Classified as Internal
Installation Next To Wall Tall Twins Single Unit Cabinet Width 32.63" Cabinet Width + Closed Door (overhang of door to cabinet) 32.86" Cabinet Width + Overhand One Side + Door Open at 90 degrees 35.82 Door Opens a Maximum 130 degrees (Does not open a full 180 degrees) *When installing this unit next to a wall it is import to take into consideration the door open at 90 degrees with the handle.
Side By Side Install Pairing Kit Revised 1/15/2021
Tall Twins Pairing Kit -Pairing kit is REQUIRED when units are installed next to each other. -Pairing kit helps optimize performance and prevent the risk of condensation.
Installation Instructions for Single-Door Freezer and Refrigerator Pairing Kit An authorized service technician is recommended to install the filtered ice kit. Components A NOTE: Confirm the power supply fits into the cutout when placed on top of the unit. Also confirm the power supply reaches the power outlet when placed on top of the unit (Fig. 4A). CAUTION The cabinet is heavy. Two people are recommended to lift or move the cabinet. 7. C 1.
Filtered Water and Ice Kit Install Revised 1/15/2021
FILTERED ICE KIT: TTFLTRICEKIT Models: INSTRUCTION SHEET FPFU19F8WF FPRU19F8WF EI33AF80WS EI33AR80WS Kit Contents: B A (1x) 218976831 1/4” Green water line, 16 feet C D C (2x) 240396805 (2x) 240396804 1/4” Green water line 1/8” Wiring harness strain relief strain relief (2x) F E (1x) A19408101 Wiring Harness 19 Feet (2x) 305346-00 Wiring Harness support clips ORIGINAL CONFIGURATION Rear View Refrigerator Rear View Freezer © 2020 Electrolux Home Products, Inc.
FILTERED ICE KIT: TTFLTRICEKIT Models: INSTRUCTION SHEET FPFU19F8WF FPRU19F8WF EI33AF80WS EI33AR80WS NOTE: This kit is designed to provide filtered water to the freezer ice maker when a single-door freezer is installed next to a single-door refrigerator. NOTE: An authorized service technician is recommended to install the filtered ice kit. NOTE: Disconnect electrical power prior to servicing this product.
Models: INSTRUCTION SHEET FPFU19F8WF FPRU19F8WF EI33AF80WS EI33AR80WS Refrigerator Connections 1. Feed the green water line (A) and wiring harness (E) through the opening of the refrigerator access cover. 2. Push the green water line into the green port of the water valve. 3. Connect the wiring harness (E), to the connector on the refrigerator. 4. Locate wiring harness support clip at top of refrigerator machine compartment (F), and insert wiring harness to secure.
Models: INSTRUCTION SHEET FPFU19F8WF FPRU19F8WF EI33AF80WS EI33AR80WS Freezer Connections NOTE: The freezer water valve and the connecting harness are not used when this kit is installed for filtered water provided by the paired refrigerator. 1. Disconnect and remove the 10” green water line by pushing upward on the port tab, while pulling out the line. 4. Connect the harness (E) from the refrigerator to the connector for the freezer.
Models: INSTRUCTION SHEET FPFU19F8WF FPRU19F8WF EI33AF80WS EI33AR80WS Water Line Final Connections 1. Fasten the strain reliefs for green water line (B) and for wiring harness on each unit. (C) 2. Attach the two adhesive support clips (F) and insert the green water line and harness. 3. Loop the water line and wire harness in the center of the two units. (F) (F) (F) (B) (C) 4. Connect and turn on water supply. 5. Purge air from water lines by dispensing water from refrigerator water dispenser.
Trim Kits and Accessories Revised 1/15/2021