TABLE OF CONTENTS Before Setting Oven Controls . . . . . . . . . . . . . . . . Setting Oven Controls . . . . . . . . . . . . . . . . . . . . . . Care and Cleaning . . . . . . . . . . . . . . . . . . . . . . . . Before You Call . . . . . . . . . . . . . . . . . . . . . . . . . . . Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 19 29 35 39 A00538901 Rev A (May 2017) Product Record and Registration . . . . . . . . . . . . . . 2 Important Safety Instructions . . . . . . . . . . .
PRODUCT RECORD AND REGISTRATION Product Record and Registration . . . . . . . . . . . . . . . . . 2 Important Safety Instructions . . . . . . . . . . . . . . . . . . . . 3 Cooking Recommendations . . . . . . . . . . . . . . . . . . . . . 9 Before Setting Surface Controls . . . . . . . . . . . . . . . . 12 Setting Surface Controls . . . . . . . . . . . . . . . . . . . . . . . 15 Before Setting Oven Controls . . . . . . . . . . . . . . . . . . 18 Setting Oven Controls . . . . . . . . . . . . . . . . . . . . .
IMPORTANT SAFETY INSTRUCTIONS Read all instructions before using this appliance. This manual contains important safety symbols and instructions. Please pay attention to these symbols and follow all instructions given. Do not attempt to install or operate your appliance until you have read the safety precautions in this manual. Safety items throughout this manual are labeled with a WARNING or CAUTION statement based on the risk type.
IMPORTANT SAFETY INSTRUCTIONS IMPORTANT INSTRUCTIONS FOR UNPACKING AND INSTALLATION Remove all tape and packaging before using the appliance. Destroy the carton and plastic bags after unpacking the appliance. Never allow children to play with packaging material. Do not remove the wiring label and other literature attached to the appliance. Do not remove model/ serial number plate. Proper Installation—Be sure your appliance is properly installed and grounded by a qualified technician.
IMPORTANT SAFETY INSTRUCTIONS IMPORTANT INSTRUCTIONS FOR USING THE APPLIANCE WARNING Storage In or On Appliance—Flammable materials should not be stored in an oven or microwave, near surface burners or elements, or in the storage or warmer drawer (if equipped). This includes paper, plastic, and cloth items, such as cookbooks, plastic ware, and towels, as well as flammable liquids. Do not store explosives, such as aerosol cans, on or near the appliance.
IMPORTANT SAFETY INSTRUCTIONS CAUTION Do not attempt to operate the appliance during a power failure. If the power fails, always turn off the appliance. If the appliance is not turned off and the power resumes, electric surface elements may resume operation when power is restored. Once the power resumes, reset the clock and the oven function. IMPORTANT INSTRUCTIONS FOR USING YOUR RADIANT COOKTOP Know which knob or key controls each surface heating area.
IMPORTANT SAFETY INSTRUCTIONS IMPORTANT INSTRUCTIONS FOR USING YOUR OVEN Protective liners—Do not use aluminum foil, aftermarket oven liners, or any other materials or devices to line oven bottom, oven racks, or any other part of the appliance. Only use aluminum as recommended for baking, such as lining cookware or as a cover placed on food. Any other use of protective liners or aluminum foil may result in a risk of electric shock or fire or a short circuit.
IMPORTANT SAFETY INSTRUCTIONS IMPORTANT INSTRUCTIONS FOR SERVICE AND MAINTENANCE Do not repair or replace any part of the appliance unless specifically recommended in the manuals. All other servicing should be done only by a qualified technician. This reduces the risk of personal injury and damage to the appliance. Always contact your dealer, distributor, service agent, or manufacturer about problems or conditions you do not understand.
COOKING RECOMMENDATIONS Bakeware The material of bakeware affects how evenly and quickly it transfers heat from the pan to the food. Material Attributes Recommendation Shiny metal bakeware Shiny, aluminum, and non-coated bakeware is the best for even heating. It is suitable for all baked goods. Recommended cooking temperatures and times are based on shiny metal bakeware. Dark metal bakeware Dark bakeware cooks hotter than shiny bakeware.
COOKING RECOMMENDATIONS Cooking Conditions Conditions in your kitchen can affect the performance of your appliance when cooking food. Condition Aging cookware High altitude Attributes Recommendation As pans age and become discolored, cooking times may need to be reduced slightly. If food is too dark or overcooked, use the minimum cook time in the recipe or packaging. Air is drier and air pressure is lower. Adjust cooking temperature, cooking time, or recipes as needed.
COOKING RECOMMENDATIONS Cooking Tips Broiling / Roasting Broiling pan For best results when broiling, use a broil pan with a broil pan insert designed to drain the fat from the food, help avoid spatter, and reduce smoking. The broiler pan will catch grease spills, and the insert helps prevent grease splatters. If a broiler pan and insert are not supplied with this appliance, they may be purchased from Frigidaire.com.
BEFORE SETTING SURFACE CONTROLS Using Proper Cookware Cookware Material Types The size and type of cookware used will influence the heat setting needed for best cooking results. Be sure to follow the recommendations for using proper cookware as illustrated in Figure 1 and Figure 2. The cookware material determines how evenly and quickly heat is transferred from the surface element to the pan bottom.
BEFORE SETTING SURFACE CONTROLS About the Ceramic Glass Cooktop About the Radiant Surface Elements The ceramic glass cooktop has heating elements below a smooth glass surface. The designs on the ceramic cooktop outline the areas of the surface elements underneath. Always match the pan size with the diameter of the element outline on the cooktop. Only flat-bottomed cookware should be used. The element temperature rises gradually and evenly. As the temperature rises, the element will glow red.
BEFORE SETTING SURFACE CONTROLS Element On and Hot Surface Indicator Lights Types of ceramic cooktop elements The ELEMENT ON indicator light will turn on when one or more elements are turned on. The circles on the ceramic glass cooktop outline the size and type of element underneath. The elements on your cooktop depend on the model. Figure 3: • A single radiant element has one circle. • A dual radiant element (some models) has two circles.
SETTING SURFACE CONTROLS Single radiant surface elements (all models) To operate the single radiant element: 1. Place correctly sized cookware on surface element. 2. Push in and turn the surface control knob in either direction (Figure 6) to the desired setting (refer to the “Suggested radiant surface element settings” in Table 1). 3. When cooking is complete, turn the radiant surface element OFF before removing the cookware.
SETTING SURFACE CONTROLS Dual radiant surface elements (some models) Symbols on the backguard will help choose which portion of the dual radiant element to set. The symbol indicates a setting for the inner element only. The symbol indicates a setting for both inner and outer elements. To operate a dual radiant element: 1. Place correctly sized cookware on the surface element. 2. Push in and turn the surface control knob clockwise to begin heating both the inner and outer elements.
SETTING SURFACE CONTROLS Home Canning Be sure to read and observe all the following points when home canning with your appliance. Check with the USDA (United States Department of Agriculture) Web site and be sure to read all the information they have available as well as follow their recommendations for home canning procedures. • Use only a completely flat bottom canner with no ridges that radiate from the bottom center when home canning. Heat is spread more evenly when the bottom surface is flat.
BEFORE SETTING OVEN CONTROLS Oven Vent Location The oven is vented as shown below. When the oven is on, warm air is released through the vent. This venting is necessary for proper air circulation in the oven and good baking results. Do not block oven vent. Never close off the openings with aluminium foil or any other material. Steam or moisture may appear near the oven vent. This is normal. • Flat oven racks may be used for most cooking needs and may be placed in most oven rack positions.
SETTING OVEN CONTROLS 1 Bake 2 9 10 Broil Timer Bake Time 11 12 3 4 Self Clean Set Clock 8 5 Oven 6 Preheat OFF 7 Door Locked 6 Hold Start Time Figure 10: Oven control Oven Control Features 1. Bake - Use to select Bake feature. 2. Broil - Use to set Broil feature. 3. Self Clean - (some models) Use to with arrow keys to set self clean cycle of 2 or 3hours. 4. Set Clock - Use with arrow keys to set the time of day. 5.
SETTING OVEN CONTROLS Table 2: Minimum and maximum control settings Feature Minimum Temp. /Time Maximum Temp. /Time Bake 170°F (77°C) 550°F (288°C) Broil LO - 400°F (205°C) HI - 550°F (288°C) Timer 0:01 Min. 11:59 Hr./Min. Clock Time 1:00 Hr./Min. 12:59 Hr./Min. Start Time (delays start of Bake) 1:00 Hr./Min. 12:59 Hr./Min. Bake Time 0:01 Min 11:59 Hr./Min.
SETTING OVEN CONTROLS Setting a silent control panel Operating oven light When selecting a function, an audible tone is heard each time a key is pressed. If desired, the control can be programmed for silent operation. The interior oven light will automatically turn on when the oven door is opened. Press the oven light switch located on the upper left control panel to turn the interior oven light on and off whenever the oven door is closed. To set the controls for silent operation: 1.
SETTING OVEN CONTROLS Setting Bake To set Bake: The oven can be programmed to bake at any temperature from 170°F to 550°F (77°C to 288°C). The factory preset automatic bake temperature is 350°F (177°C). 1. Press Bake. — — — appears in the display. Baking Tips For best bake results: • Fully preheat the oven before baking. • For best results when baking cakes using two oven racks, place racks in positions 1 and 3 (See Figure 12).
SETTING OVEN CONTROLS Setting Bake Time Setting Start Time (delayed start) The Bake Time key sets the amount of time needed for baking. The oven will turn on immediately and stop automatically after the set bake time ends. Use the Start Time key to delay the starting time (delayed timed bake). The oven will turn on at a later time and stop automatically after the set bake time ends.
SETTING OVEN CONTROLS Adjusting the oven temperature To adjust oven temperature: Your appliance has been factory calibrated and tested to ensure an accurate baking temperature. For the first few uses, follow your recipe times and temperature recommendations carefully. If you think the oven is cooking too hot or too cool for your recipe times, you can adjust the control so the oven cooks hotter or cooler than the temperature displayed. 1. Press Bake.
SETTING OVEN CONTROLS Setting Broil Broiling is direct heat cooking and will produce some smoke. If smoke is excessive, place food further away from the element. Watch food to prevent burning. When broiling, always remember to arrange the oven racks while oven is still cool. Position the rack as suggested in Table 3. WARNING Should an oven fire occur, close the oven door and turn the oven off. If the fire continues, use a fire extinguisher. Do not put water or flour on the fire. Flour may be explosive.
SETTING OVEN CONTROLS Table 3: Broil recommendations Food item Rack Position Temp Steak 1” thick 3 or 4 (550°F) 6:00 4:00 135°F (57°C) Rare** Steak 1” thick 3 or 4 (550°F) 7:00 5:00 145ºF (63ºC) Medium Pork Chops 3/4 “thick 3 or 4 (550°F) 8:00 6:00 170°F (77ºC) Chicken - Bone In 3 (450°F) 20:00 10:00 170°F (77ºC) Well Chicken Boneless 3 or 4 (450°F) 8:00 6:00 170°F (77ºC) Well Fish 3 (500°F) 13:00 -- 170°F (77ºC) Well Shrimp 3 (550°F) 5:00 -- 170°F (77ºC)
SETTING OVEN CONTROLS Self Clean A self cleaning oven cleans itself with temperatures well above normal cooking temperatures which eliminate soils completely or reduces them to a fine powdered ash you can wipe away with a damp cloth. While the oven is in operation, the oven heats to temperature much higher than those used in normal cooking. Sounds of metal expansion and contraction are normal. Oder is also normal because the food soil is being removed. Smoke may appear through the oven vent.
SETTING OVEN CONTROLS To set a self clean cycle or a delayed start self clean cycle: been activated): 1. Be sure the clock displays the correct time of day. 1. Press OFF. IMPORTANT To start a self clean cycle immediately without a delay, skip Step 2 and Step 3 in the instructions provided below. To stop or interrupt a self clean cycle (once it has 2. Once the oven has cooled down for about 1 hour and the door locked light has turned off, the oven door can be opened. 3.
CARE AND CLEANING Remove spills and any heavy soiling as soon as possible. Regular cleaning will reduce the difficulty of major cleaning later. CAUTION • Before cleaning any part of the appliance, be sure all controls are turned off and the appliance is cool. • If ammonia or appliance cleaners are used, they must be removed and the appliance must be thoroughly rinsed before operating. Follow manufacturer's instructions and provide adequate ventilation.
CARE AND CLEANING Porcelain-enameled broiler pan and insert Porcelain door liner Porcelain body parts (some models) Rinse with clean water and a damp cloth. Scrub gently with a soapy, non-abrasive scouring pad to remove most spots. Rinse with a 50/50 solution of clean water and ammonia. If necessary, cover difficult spots with an ammonia-soaked paper towel for 30 to 40 minutes. Rinse and wipe dry with a clean cloth. Remove all cleaners or future heating could damage the porcelain.
CARE AND CLEANING Cooktop Maintenance Consistent and proper cleaning is essential to maintaining your ceramic glass cooktop. Prior to using your cooktop for the first time, apply a ceramic cooktop cleaning cream (available in most hardware, grocery, and department stores) to the ceramic surface. Clean and buff with a clean paper towel. This will make cleaning easier when soiled from cooking. Cooktop cleaning creams leave a protective finish on the glass to help prevent scratches and abrasions.
CARE AND CLEANING Cooktop Maintenance (cont’d) IMPORTANT Damage to the ceramic glass cooktop may occur if you use an abrasive type cleaning pad. Only use cleaning products that have been specifically designed for ceramic glass cooktops. Cleaning under bake element (some models) The bake element is located in the lower oven cavity. For some models, if the lower bake element is visible it may be tilted up for easier access to the oven bottom for cleaning. Remove the oven racks before raising the element.
CARE AND CLEANING Removing and Replacing the Oven Door To remove oven door: Oven door hinge locations CAUTION The door is heavy. For safe, temporary storage, lay the door flat with the inside of the door facing down. 1. Open oven door completely, horizontal with floor (See Figure 20). 2. Pull the door hinge locks on both left and right door hinges down from the oven frame completely towards the oven door (See Figure 21). A tool such as a small flat-blade screwdriver may be required.
CARE AND CLEANING Replacing the Oven Light CAUTION Be sure the oven is unplugged and all parts are cool before replacing the oven light. Replacing the oven interior light bulb: The interior oven light is located at the rear of the oven cavity and covered with a glass shield. The glass shield must be in place whenever the oven is in use (Figure 24). Remove and replace storage drawer (some models) Use the storage drawer for storing cooking utensils.
BEFORE YOU CALL Oven Baking For best cooking results, preheat the oven before baking cookies, breads, cakes, pies, pastries, etc. There is no need to preheat the oven for roasting meat or baking casseroles. The cooking times and temperatures needed to bake a product may vary slightly from your previously owned appliance. Baking Problems and Solutions Baking Problems Causes Cookies and biscuits burn • on the bottom. Cookies and biscuits put into • oven before oven is preheated. • Oven rack is overcrowded.
BEFORE YOU CALL Solutions to Common Problems: Before you call for service, review the following list. It may save you time and expense. Possible solutions are provided with the problem listed. Problem Cause / Solution Entire appliance does not operate. Appliance not connected. Make sure power cord is plugged properly into outlet. Check your fuse box or breaker box to make sure the circuit is active. Electrical power outage. Check house lights to be sure.
BEFORE YOU CALL Problem Cause / Solution Cooktop Problems Surface element is too hot or not hot enough. Incorrect surface control setting. Adjust power level setting. Surface element does not heat or does not heat evenly. Be sure the correct surface control knob is turned on for the element needed. Areas of discoloration with metallic sheen on cooktop surface. Mineral deposits from water and food. Remove them using cooktop cleaning creme applied to the ceramic surface.
BEFORE YOU CALL Problem Cause / Solution Soil not completely removed after self clean. Self clean was interrupted. Review instructions on “Self Clean” on page 26. Excessive spills on oven bottom. Remove excessive spills before starting self clean. Failure to clean soil from the oven frame, the door liner outside the oven door gasket, and the small area at the front center of the oven bottom. These areas are not in the self-cleaning area, but get hot enough to burn on residue.
WARRANTY Your appliance is covered by a one year limited warranty. For one year from your original date of purchase, Electrolux will pay all costs for repairing or replacing any parts of this appliance that prove to be defective in materials or workmanship when such appliance is installed, used and maintained in accordance with the provided instructions. Exclusions This warranty does not cover the following: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13.