Installation guide

ManualsBrandsFrigidaire ManualsRangeOfficial Frigidaire electric range

_NSTALLAT_ON AND SERVICE MUST BE PERFORMED BY A QUAUF_ED _NSTALLER.

_MPORTANT: SAVE FOR LOCAL ELECTRICAL _NSPECTOR'S USE.

READ AND SAVE THESE _NSTRUCT_ONS FOR FUTURE REFERENCE.

For existing 29" (73,7 cm) cutout wide opening, you

must calI the Service Center for optional thinner side

panels. Also you must prepare the countertop edge as

shown on page 5.

These surfaces should be flat &

leveled (hatched area).

1V2"Max. I/2" rain.

(3,8cm) Max,

30 "

(76.2 cm)

30" Min.

(76,2 cm Min.)

SeeNote3

18" Min.

rain. (45,7cm Min.)

ShaveRaisedEdgeto

ClearSpacefor a

31V2"(81cm)Wide

Cooktop Rim.

Locate Cabinet Doors

1" (2,5 cm) Min.

from Cutout Opening

(61 cmMin.)

Smoothtop Models

48" (122 cm)

Armored CaMe

NOTE: Two sets of holes are provided

under anti-tip bracket. Bracket is

attached in the upper hole position at

the factory. Refer also to page 5, item 9

for additional details.

Grounded Junction Boxin

adjoining Cabinet

iMPORTANT: Cabinet and countertop width

should match the cutout width.

A, Cuteut Width BoCutout Depth C Height Of

(Ceuntertop and !According to front

Cabinet) ' of cabinet)

30±1116" 21 3/4" (55,2 crn) rain 29" (73,7 cm)

(76,2±0,15cm) 22 1/8" (56,2 cm) max

Printed in United States P/N 318201613 (0510) Rev C

English - pages I-6

Espaflol - p_iginas 7-12

Summary of content (16 pages)

PAGE 1
_NSTALLAT_ON AND SERVICE MUST BE PERFORMED BY A QUAUF_ED _NSTALLER. _MPORTANT: SAVE FOR LOCAL ELECTRICAL _NSPECTOR'S USE. READ AND SAVE THESE _NSTRUCT_ONS FOR FUTURE REFERENCE. 30 For existing 29" (73,7 cm) cutout wide opening, you must calI the Service Center for optional thinner side panels. Also you must prepare the countertop edge as shown on page 5. These surfaces should be flat & leveled (hatched area). 1V2"Max. I/2" (3,8cm) Max, " (76.2 cm) 30" Min. (76,2 cm Min.) SeeNote 3 rain. rain. 18" Min.
PAGE 2
1. Do not pinch the power supply cord between the range and the wail. Do not seal the range to the side cabinets. 3. 4. 24" (61 cm)minimum clearance between the cooktop and the bottom of the cabinet when the bottom of wood or metal cabinet is protected by not iess than 1/4" (0.64 cm) flame retardant miliboard covered with not less than No. 28 MSG sheet metal, 0.015" (0.4 mm) stainiess steei, 0.024" (0.6 mm) aluminum, or 0.020" (0.5 ram) copper. 30" (76.
PAGE 3
Important Notes to the Installer 1. Readallinstructions contained intheseinstallation instructions beforeinstalling range. 2. Remove allpackingmaterialfromtheovenbefore connecting theelectrical supplyto therange, 3. Observe allgoverning codesandordinances, 4. Besureto leavetheseinstructions withtheconsumer. 5. Ovendoormayberemoved to facilitateinstallation. 6. Donotlift therangebythedoorhandle. ImportantNoteto the Consumer Keeptheseinstructions withyourowner'sguideforfuture reference.
PAGE 4
Electrical Cable Requirements This appliance must be supplied with the proper voltage and frequency, and connected to an individual, properly grounded branch circuit, protected by a circuit breaker or fuse, having amperage as noted on the rating plate (the rating plate is located on the oven frame). White WEre (Neutral) from Residence Black Wires] If local codes permit, you (:an use a 3-wire single phase 120/208 or 120/240 Volt, 60Hz AC only electrical system.
PAGE 5
improper connection • If the existing cutout width is greater than 30 1/!6" (76,4 cm), reduce the 3A" (1.9 dimension. of aluminum house wiring to copper Jeads can result in a short circuit or fire. Use only connectors designed for joining copper to aluminum, and fo!low the manufacturer's recommended procedure closely. NOTE TO ELECTRICIAN: The armored cable leads (1.9cm) supplied with this appliance are UL-recognized for connection to larger gauge household wiring.
PAGE 6
This range is designed to hang from the countertop. does not rest on the floor. It Be sure the bottom of any wall cabinets are a minimum of 30" (76.2 cm) above the rangetop area. To eliminate the hazard or reaching over heated surface units, cabinet storage space located above the surface units should be avoided. If cabinet storage is to be provided, the hazard can be reduced by installing a range hood that projects horizontally a minimum of 5" (12.7 cm) beyond the bottom front edge of the cabinets.
PAGE 7
Anti-Tip mountingscrews 2 oneach Broil-When the oven is set to BROIL, the upper element in tile oven should become red. Clean (some models)-When the oven is set for a selfcleaning cycle, the upper element should become red during the preheat portion of tile cycle. After reaching the self-cleaning temperature, the lower element will become red. Convection (some models)-When the oven is set for convection baking or roasting, both elements cycle on and off alternately and the convection fan will turn.
PAGE 8
LA [NSTALACION Y EL SERV[aO DEBEN SER EFECTUADOS POR UN [NSTALADOR CAL[F[CADO. [MPORTANTE: GUARDE ESTAS [NSTRUCCIONES PARA USO DEL INSPECTOR LOCAL DE ELECTRIC[DAD. LEA Y GUARDE ESTAS [NSTRUCC[ONES PARA REFERENC[A FUTURA. VOTA: Para 29" (73,7 cm) anchura de la abertura, 30" (76.2 cm), _sted debe Ilamar al Centro de Servicios para los panties aterales opcionales y borde ancho daro del cooktop (yea p_flgina 10).
PAGE 9
NOTAS: 1. No petlizque el cord6n el_ctrico entre la estufa y la pared. 2. No 8elle la estufa a Io8 armarios lado. de 3. Un espacio minimo de 24" (61 cm) entre Ia superficie de Ia estufa y el fondo deI armario cuando el fondo det armario de madera o metal est,1 protegido pot no menos de 1/4" (0.64 cm) de madera resistente aI fuego cubierta pot una lamina met_ilica de MSG, nOmero 28, 0.015" (0.4 mm) de acero inoxidabte, 0.024" (0.6 mm) de aluminio, 6 0.02" (0.5 mm) de cobre.
PAGE 10
Notas importantes Lea todas las instrucciones contenidas en este manual antes de instalar la estufa. 2. Saque todo el material usado en el embalaje del compartimiento del homo antes de conectar el suministro electrico ala estufa. 3. 4. 5. Observe todos los c6digos y reglamentos pertinentes. Deje estas instrucciones con el comprador. Pare facilitar la instalacion puede quitarse la puerta del horno. 6. No levante la estufa por la manila de la puerta.
PAGE 11
Requisitos Este aparato esta fabricado con un alambre electrico neutro (blanco) y un alambre verde (o alambre pelado) de puesta a tierra conectado al gabinete. el ctricos Este artefacto debe ser suministrado con el voltaje y la frecuencia adecuados, y conectado a un circuito individual correctamente puesto a tierra, protegido por un (ortacircuitos o un fusible con el amperio anotado en la plata de calificacion (la placa se encuentra en el armaz6n del horno).
PAGE 12
lnstalad6n Una conexi6n incorrecta de! de aluminio con los conductores a[ambrado cobre puede resu[tar en un cortadrcuito Use soiamente [os conectores dise_ados de de la estufa La corriente el_ctrica a [a estufa debe apagarse m[entras se hagan tas conexiones. S[ no se hace esto puede provocar daho serio o muerte. o incendioo para juntar el cobre con e[ aluminio y siga exactamente e[ procedirniento recornendado pot e[ fabricante.
PAGE 13
Paraeliminarel peligrodetenerqueextender elbrazopor encimadelasuperficie calientedelaestufa,sedebe evitarlainstalacion degabinetes porencimadeella.Si hayqueinstalargabinetesporencimadelaestufa, se puedereducirelriesgoinstalando unventilador deestufa queseproyecte horizontalmente unminimode5" (12.7 cm)masaliadelhordedelantero inferiordelosgabinetes. Notaimportante:Noesnecesario, perosies conveniente, quitarla puertaparainstalarelhorno. Consulte lasinstrucciones pararetirarlapuertaenlaGuia deUsoy Cuidado.
PAGE 14
Clean/Limpieza (algunos mode[os)-( uando el homo esta puesto para un ciclo de autoqimpieza, el elemento superior se pondra rojo durante el per[odo de precalentamiento del ci(Io. Despu6s de alcanzar la temperatura de autoqimpieza, el elemento inferior se pondra rojo. Tornillos antivuelco t Convection/Convecd6n (a[gunos mode[os)--Cuando el homo se pone a CONV/BAKE los dos elementos se encienden y se apagan alternando en un ciclo y el ventiladorseponeen marcha.
PAGE 15
Notas .
PAGE 16
Notas .