WP201 Access Point User Manual Part Number: LUM0073AA Revision: Aug-2015
Safety Information The products described in this manual can fail in a variety of modes due to misuse, age, or malfunction. Systems with these products must be designed to prevent personal injury and property damage during product operation and in the event of product failure. Warning! Do not remove or insert the Ethernet or diagnostics cable while circuit is live unless the area is known to be free of ignition concentrations of flammable gasses or vapors. Warranty FreeWave Technologies, Inc.
WP201 Access Point: User Manual WP201® Return Material Authorization (RMA) Policy and Procedures This policy describes the responsibilities and procedures of the Customer and FreeWave when a WP201® device return is required. When a request for a WP201® device replacement has been validated by FreeWave’s Customer Support, FreeWave’s policy for processing the device returned due to a fault is to replace the device with a new or refurbished device upon receipt of the reported faulty product.
obtaining all necessary U.S. government authorizations required to ensure compliance with these and other applicable U.S. laws. Consult with your legal counsel for further guidance. FCC Notifications This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference and 2) this device must accept any interference received, including interference that may cause undesired operation.
WP201 Access Point: User Manual Table Of Contents Preface 7 1. WP201 Overview 9 1.1 System Requirements 10 1.2 User-supplied Equipment 10 1.3 WP201 Included Accessories 11 1.4 WP201 Hardware Layout 13 1.4.1 Front of the WP201 13 1.4.2 Back of the WP201 14 1.4.3 Left Side of the WP201 15 1.4.4 Bottom of the WP201 15 1.4.5 Right Side of the WP201 16 2. WP201 Installation and Setup 17 2.1 Connect to the WP201 Access Point 18 2.2 WP201 IP Address Configuration 19 2.
Page 6 of 38 LUM0073AA Rev Aug-2015 This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned by FreeWave®. This document cannot be reproduced in whole or in part by any means without written permission from FreeWave Technologies, Inc.
WP201 Access Point: User Manual Preface Where to Find Additional Information WP201 Quick Start Guide Use the FreeWave website www.freewave.com to download the latest version of the Quick Start Guide. Contacting FreeWave Technical Support For up-to-date troubleshooting information, check the Support page at www.freewave.com. FreeWave provides technical support Monday through Friday, 8:00 AM to 5:00 PM Mountain Time (GMT -7). l Call toll-free at 1.866.923.6168. l In Colorado, call 303.381.9200.
Preface l FreeWave applications appear as: FreeWave. l Parameter setting text appears as: [Page=radioSettings] l File names appear as: configuration.cfg. l File paths appear as: C:\Program Files (x86)\FreeWave Technologies. l User-entered text appears as: xxxxxxxxx. l 3rd-party names appear as: Notepad®. Caution: Indicates a situation that MAY cause damage to personnel, the radio, data, or network. Example: Provides example information of the related text.
WP201 Access Point: User Manual 1. WP201 Overview Thank you for purchasing the WP201 Access Point. The FreeWave WP201 is a high-powered, long-range, 3x3 Dual-Band, Wireless, 802.11ac/a/b/g/n Outdoor Access Point. It can be configured as: l an Access Point. l a Client Bridge. l a Wireless Distribution System (WDS-AP, Station, or Bridge). The FreeWave WP201: l l l is easy to install in almost any location with its PoE (Power over Ethernet) Injector for quick outdoor installation.
1. WP201 Overview Example: Several WP201 Access Points can be deployed in a campus setting using the 5GHz band as a backhaul to provide multiple 2.4GHz wireless cells for computers or mobile devices in common outdoor areas. l A maximum of 29dBm transmit power, enabling long range connectivity. l There are three detachable: l 5dBi 2.4GHz omni-directional antennas. l 7dBi 5GHz omni-directional antennas. l Mesh Supported (2.4GHz). l 802.3at - capable switches or injectors.
WP201 Access Point: User Manual 1.
1. WP201 Overview Figure 1: WP201 Included Accessories Page 12 of 38 LUM0073AA Rev Aug-2015 This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned by FreeWave®. This document cannot be reproduced in whole or in part by any means without written permission from FreeWave Technologies, Inc.
WP201 Access Point: User Manual 1.4 WP201 Hardware Layout These images identify the hardware layout of the WP201. 1.4.1 Front of the WP201 Figure 2: Front of the WP201 Front of the WP201 # Name Description Accessory Location*** 1 2.4 GHz Antennas Detachable 5 dBi 2.4 GHz omni-directional H 2 5 GHz Antennas Detachable 7 dBi 5 GHz omni-directional H Note: ***See WP201 Included Accessories (on page 11).
1. WP201 Overview 1.4.2 Back of the WP201 Figure 3: Back of the WP201 Back of the WP201 # Name Description Accessory Location*** 3 Ground screw hole Using the enclosed Packaged Ground Screw, attach the loop end of one of the supplied Green Ground Cables to the ground point on the Back of the WP201 (on page 14). E Important!: The Green Ground Cable MUST BE attached to the WP201 BEFORE the Mounting Bracket is attached.
WP201 Access Point: User Manual 1.4.3 Left Side of the WP201 Figure 4: Left Side of the WP201 Left Side of the WP201 # Name Description 5 Serial Number label The Serial Number of the WP201 is 10 digits: l 123-456-7890 1.4.4 Bottom of the WP201 Figure 5: Bottom of the WP201 Bottom of the WP201 # Name Description 6 5GHz Antenna Detachable 7 dBi 5 GHz omni-directional 7 LAN Port 1 (PoE Input) 802.3at Ethernet port for RJ-45 cable. 8 2.4GHz Antenna Detachable 5 dBi 2.
1. WP201 Overview 1.4.5 Right Side of the WP201 Figure 6: Right of the WP201 Front of the WP201 # Name Description 11 LED Indicators: LED lights The LEDs are: l Power l LAN Port 1 l LAN Port 2 l 2.4 GHz Connection l 5 GHz Connection Note: ***See WP201 Included Accessories (on page 11). Page 16 of 38 LUM0073AA Rev Aug-2015 This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned by FreeWave®.
WP201 Access Point: User Manual 2. WP201 Installation and Setup This section provides procedure information about installation and initial setup of the WP201. l Connect to the WP201 Access Point (on page 18). l WP201 IP Address Configuration (on page 19). l Access the WP201 (on page 22). l Changing the WP201 Mode (on page 23). l Wall Mounting the WP201 (on page 25). l Pole Mounting the WP201 (on page 29).
2. WP201 Installation and Setup 2.1 Connect to the WP201 Access Point 1. Attach and gently tighten the provided antennas to the appropriate port on the WP201. 2. Attach one of the supplied Green Ground Cables to the Ground screw on the PoE Injector. 3. Attach the other end of the Green Ground Cable to a weather-proof ground. 4. Using one of the CAT5e Ethernet cables, connect one end of the cable to the LAN 1 Port (PoE Input) of the WP201 and the other end into the AP/Bridge port on the PoE Injector. 5.
WP201 Access Point: User Manual 2.2 WP201 IP Address Configuration 1. Turn on the computer. 2. Click the Windows® Start button and select Control Panel. 3. Click Network and Internet > View Network Status and Tasks. 4. Click the Change adapter settings link. 5. Double-click the Local Area Connection link. Figure 8: Local Area Connection link The Local Area Connection Status dialog box opens. Figure 9: Local Area Connection Status dialog box 6. Click Properties.
2. WP201 Installation and Setup Figure 10: Local Area Connection Properties dialog box 8. Click Properties. The Internet Protocol Version 4 (TCP/IPv4) Properties dialog box opens. 9. Select the Use the following IP address option button. 10. In the IP Address text box, enter an IP Address that is DIFFERENT from the WP201. Page 20 of 38 LUM0073AA Rev Aug-2015 This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned by FreeWave®.
WP201 Access Point: User Manual Figure 11: Local Area Connection Properties dialog box Note: The default WP201 IP Address is 192.168.1.1. Example: Enter an IP Address from 192.168.1.2 to 192.168.1.254 and the Subnet Mask to 255.255.255.0. 11. Click OK to save the changes and close the dialog box. 12. Click Close twice to close the Local Area Connection Properties and Local Area Connection Status dialog boxes.
2. WP201 Installation and Setup 2.3 Access the WP201 1. Open a web browser. 2. In the address bar of the browser, enter 192.168.1.1. Figure 12: Entered IP Address 3. Press . The Login dialog box opens. 4. Enter the default Username and Password (admin for both) and click Login. The Device Information window opens. Figure 13: Device Information window Page 22 of 38 LUM0073AA Rev Aug-2015 This document is the property of FreeWave Technologies, Inc.
WP201 Access Point: User Manual 2.4 Changing the WP201 Mode 1. In the Access Panel on the left, click Network > Wireless. The Wireless window opens. Figure 14: Wireless window 2. Click the Operation Mode list box arrow for the designated frequency and select the applicable Mode for the WP201. Note: See Modes for detailed information and examples about the different modes. 3. Scroll to the bottom of the window and click Save. Figure 15: Wireless window A Processing bar appears.
2. WP201 Installation and Setup The Wireless Settings window refreshes. The Changes tab now shows the number of changes to process. 4. Click the Changes tab. Figure 16: Changes tab showing the number of changes The Unsaved window opens. Figure 17: Unsaved window 5. Click Apply to implement all the changes made. A Processing bar appears. The Device Information window reappears when the processing is completed. 6. Optional: In the Access Panel on the left, click Network > Wireless to view the saved changes.
WP201 Access Point: User Manual 2.5 Wall Mounting the WP201 Tools Needed for this Procedure l Drill l Screwdriver l 8mm drill bit l Pliers l Hammer l Box-end wrenches Procedure Note: For illustration purposes, the images in this section DO NOT have the antennas or cables attached to the WP201. 1. Using the Mounting Bracket as a template, mark the locations of the mounting holes on the wall. Figure 18: Marked locations of the mounting holes. 2.
2. WP201 Installation and Setup 4. Verify all antennas are attached to their correct ports and the Ethernet cable is connected between the PoE Injector and the WP201. 5. Using the enclosed Packaged Ground Screw, attach the loop end of one of the supplied Green Ground Cables to the ground point on the Back of the WP201 (on page 14). Figure 20: Attached Ground Cable 6. Place the lock and flat washers on the four hex cap screws.
WP201 Access Point: User Manual 7. Insert and tighten the screws to attach the bracket to the Back of the WP201 (on page 14). Figure 21: Insert and tighten the screws to attach the bracket. LUM0073AA Rev Aug-2015 Page 27 of 38 This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned by FreeWave®. This document cannot be reproduced in whole or in part by any means without written permission from FreeWave Technologies, Inc.
2. WP201 Installation and Setup 8. Tighten the nut and flat washers to secure the bracket to the mounting surface. Figure 22: Tighten the nut and flat washers to secure the bracket. 9. Attach the wire end of the Green Ground Cable to a grounding rod (the loop end was attached to the WP201 in a previous step). Page 28 of 38 LUM0073AA Rev Aug-2015 This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned by FreeWave®.
WP201 Access Point: User Manual 2.6 Pole Mounting the WP201 Tools Needed for this Procedure l Drill l Screwdriver l 8mm drill bit l Pliers l Hammer l Box-end wrenches Procedure Note: For illustration purposes, the images in this section DO NOT have the antennas or cables attached to the WP201. 1. Verify all antennas are attached to their correct ports and the Ethernet cable is connected between the PoE Injector and the WP201. 2.
2. WP201 Installation and Setup 4. Insert and tighten the screws to attach the bracket to the Back of the WP201 (on page 14). Figure 24: Insert and tighten the screws to attach the bracket. Page 30 of 38 LUM0073AA Rev Aug-2015 This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned by FreeWave®. This document cannot be reproduced in whole or in part by any means without written permission from FreeWave Technologies, Inc.
WP201 Access Point: User Manual 5. Insert and tighten the four round head screws to attach the Pole Mount Bracket to the bracket. Figure 25: Insert and tighten the four round head screws. LUM0073AA Rev Aug-2015 Page 31 of 38 This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned by FreeWave®. This document cannot be reproduced in whole or in part by any means without written permission from FreeWave Technologies, Inc.
2. WP201 Installation and Setup 6. Thread the open end of the Pole Strap through the two tabs on the Pole Mount Bracket. Figure 26: Thread the open end of the Pole Strap. Page 32 of 38 LUM0073AA Rev Aug-2015 This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned by FreeWave®. This document cannot be reproduced in whole or in part by any means without written permission from FreeWave Technologies, Inc.
WP201 Access Point: User Manual 7. Lock and tighten the Pole Strap to secure the Pole Mount Bracket to the pole. Figure 27: Lock and tighten the Pole Strap. 8. Attach the wire end of the Green Ground Cable to a grounding rod (the loop end was attached to the WP201 in a previous step). LUM0073AA Rev Aug-2015 Page 33 of 38 This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned by FreeWave®.
Page 34 of 38 LUM0073AA Rev Aug-2015 This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned by FreeWave®. This document cannot be reproduced in whole or in part by any means without written permission from FreeWave Technologies, Inc.
WP201 Access Point: User Manual Appendix A: WP201 Technical Specifications Specifications may change at any time without notice. For the most up-to-date specifications information, see the product's data sheet available at www.freewave.com. WP201 Technical Specifications Specification Description Wireless Interfaces Network Configurations RF Frequency Support l PTP l PtMP l Fixed Point Mesh l Mobile Mesh 2.41 to 2.47 GHz (ITU ISM band) 5.15 to 5.
Appendix A: WP201 Technical Specifications WP201 Technical Specifications Specification Description Wired Interfaces Network Interface 2 - 10/100/1000 Gigabit Ethernet port with PoE support 2 LAN Ports: LAN / WAN l 1 - LAN 1 Port - PoE Input l 1 - LAN 2 Port - PSE Output 802.3 and 802.3u, IPv4, TCP, UDP, ICMP DHCP Server and Client, NAT VLAN LAN Security l VLAN Pass-through l VLAN Tag RADIUS, X.
WP201 Access Point: User Manual LUM0073AA Rev Aug-2015 Page 37 of 38 This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned by FreeWave®. This document cannot be reproduced in whole or in part by any means without written permission from FreeWave Technologies, Inc.
