Free Man UNPACKING P FEATURES P8 OPERATION DEPTH ADJUSTMENT FRIG THE TOOL P10 MAINTENANCE P11 RECOMMENDED HOOKUP P12 TROUBLESHOOTING P13 WEARABLE PATHS Pi3 WARRANTIES P14 WARNING: The wakings and precautions discussed In this manual cannot cover all possible conditions and institution that may occur. Plazas be aware of the potential hazards, and take all necessary precautions to avoid risk of Injuries.
Free Man @Do not use on a ladder or unstable ‘supports. Stable footing on a dolls surface enables better control of the tool In unexpected situations. ®Make sirs the hiss Is fees of obstructions or snags. Entangled or snarled hoses can cause loss of balance or fooling and may become damaged, resulting in possible injury. ® Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables W cancer and birth defects or other reproductive harm.
Free Man MODEL: Q22183CLW MODEL: G221383CLW Such precautionary measures race the sk FEATURES OPERATION of injury to personae SPECIFICATIONS LOADING FASTENERS LOADING TOOL AR CONSUMPTION: 11.95 SCAM with 100 1.Connect the tool to the alr source. ® Do not load the tool with fasteners when tanagers per minus @ 90 ps! 2.Insert strip of fasteners from the rear of any one of the operating controls Is g g g7y 174 inch NPT magazine (A]. Be sure the fasteners are discharge area 3 " @ Never point the tool at anyone.
MODEL: Q22183CLW Free Man A\ WARNING: A\ WARNING: Over load fasteners with the workplace contact or trigger activated. Doing so could resit In serious 1. Disconnect the tool from air source. 2. Pull back the pusher, pressing bypass lever of the pusher to allow pusher to bypass nails and slowly allow pusher to return to nose of the tool. {See figure 5) 3. Side the fastener to the rear magazine.
7 Tun the adjustment knob count clockwise CAUTION: It is advisable to teat the depth on a scrap To determine depth of drive, first adjust the air pressure and drive a test fastener. Never excess 120 psl. FIRING THE TOOL The tool Is equipped with a electable trigger ‘with two firing modes: SEQUENTIAL RING MODE Single sequential actuation provides the most accurate fastener placement. This is considered to be more restrictive mode of ‘operation, suitable for less experienced users.
CLEANING Av old using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may he damaged by their use. Use clean cloths to remove dirt, dust, ofl, grass, sic. A WARNING: COLD WEATHER OPERATION For cold weather operation, near and below freezing, the moisture in the air ine may freeze and prevent tool operation. We recommend the use of alr tool lubricant or permanent antifreeze (ethylene glycol) as a cold weather lubricant.
MODEL: G22183CLW FREEMAN PGP INC. PRODUCT WARRANTIES FREEMAN Pneumatic Nail Suns Warranties 7 Year Professional Tool Warranty The Freeman Tool limited warranty extends exclusively to the original purchaser of the Freeman Product, begins on the date of purchase and excludes wearable parts. During the warranty period Prime Global Products, Inc. (PGP) expressly warrants that the Freeman Product s free from defect In materials and workmanship subject to the exceptions and Imitations contained herein.
OPERACIÓN COMO CARGAR LOS SUJETADORES 1. Contactas ka herramienta a la fuente de aire. 2. Coloque i instilan de sujetadores en la parte posterior del cargador {A). Asegúrese de que los sujetadores apunten lacha abajo. (Figurarme 1 &figurón) Esta herramienta utiliza una alance de §. sobrepaso accionada por resorte para cargar y descargar los clavos. Una vez que. los clavos estén insertados correctamente, aire del empujador (B) completamente lacha apartarla trasera de la reamara. (Ver figura 3) 4.