Exhibit 9 HIT-NOT Proximity System Magnetic Field XL Generator User’s Manual v1.0 FREDERICK ENERGY PRODUCTS, LLC 1769 Jeff Road Huntsville, AL 35806 1.800.489.
Exhibit 9 Table of Contents 1. Overview………………………………………………………………………………………………………….. 2-5 1.1 Theory of Operation……………………………………………………………………………… 2 1.2 Operating Frequency….………………………………………………………………………… 2 1.3 Label Information…………………………………………………………………………………. 2-3 1.4 FCC/IC Information……………………………………………………………………….….….. 4-5 2. Operation…………………………………………………………………………………………………………. 5-11 2.1 Installation Information………………………………………………………………………… 5 2.1.1 Interoperability Warning………………………………………………………………... 5 2.
Exhibit 9 1 Overview The Magnetic Field XL Generator is part of a complete HIT-NOT Proximity Detection system from Frederick Energy Products which provides audible and visual warnings to both individuals and to vehicle operators to alert them that the individual has entered too close to an operating piece of equipment and is in a dangerous situation. The Magnetic Field XL Generator attaches directly to a vehicle or piece of machinery.
Exhibit 9 www.hitnot.com Power In: 12/24Vdc 3A FCC ID: QUI-HN-MFG-XL IC: 11625A-HNMFGXL Frederick Energy Products, LLC Model: HN-MFG-XL Canada 310 MAGNETIC FIELD XL GENERATOR This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. www.hitnot.
Exhibit 9 --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/technician for help. Conformité aux normes FCC Cet équipement a été testé trouvé conforme aux limites pour un dispositif numérique de classe B, conformément à la Partie 15 des règlements de la FCC.
Exhibit 9 (2) cet appareil doit accepter toute interférence, y compris des interférences qui peuvent provoquer un fonctionnement indésirable du périphérique. 2 Operation 2.1 Installation Information The Magnetic Field XL Generator is mounted on a vehicle or piece of machinery. Metal near the Magnetic Field XL Generator may impact performance by reducing the field size. After installing the Magnetic Field XL Generator on the machine, performance of the unit should be verified by operation and test. 2.
Exhibit 9 The volume to the Warning Module can be adjusted by turning plastic cover on the Warning Module. Adjustments must be made by a professional. 2.6 Interferences The Magnetic Field XL Generator may receive false triggering (generate an alarm) signals from some RF-based devices including high power radios and cell phones. Such devices will need to be moved further away from the XL Generator.
Exhibit 9 2.8 XL Generator System Installation Guide To Be Installed By a Professional Power Cable Step 2 Step 1 Install Generator Connect to a switched and fused (5A) circuit. Power to Generator Install Warning Module This connection pointed up Step 4 Step 3 Power Cable Connect Power Cable (female) to Generator (male). Turn locking ring to secure the connection. Place magnet side of the Warning Module to the frame of the forklift where it can be seen and heard by the operator.
Exhibit 9 Cab Silencer Field Adjust Step 9 • • • • • Step 8 In order to avoid battery drain while the vehicle is off, the Cab Silencer can be connected to a switched and fused (5A) circuit. Place the Cab Silencer within 21” (53cm) of the Operator’s PAD AND 4 ft (1.2m) away from the generator, Remove the screw under the PWM arrow. Have a Pedestrian with a PAD at the desired Danger Zone limit (~34’ max.
Exhibit 9 AT YOUR OWN INDEPENDENT DISCRETION AND RISK. THE HOT-NOT® SYSTEM IS NOT GUARANTEED TO PREVENT ACCIDENTS. ACCEPTANCE AND DEFINITIONS. (A) Acceptance of Terms. These Warranty Terms and Conditions (these “Terms”) are a legal agreement between You, as a purchaser and end user of the System and Frederick Energy Products, LLC. By installing the System or using the System in any way, You are (1) agreeing to be bound by these Terms.
Exhibit 9 INDEMNIFICATION; RELEASE; LIMITATION OF LIABILITY. (A) Indemnification.
Exhibit 9 confidence. No action, regardless of form, related to the obligations of the parties under this Agreement may be brought by either party against the other more than one (1) year after the cause of action has accrued. In any proceeding to enforce this Agreement, the prevailing party will have the right, in addition to its other rights hereunder, to recover its reasonable litigation costs and reasonable attorneys’ fees.
Exhibit 9 4 Revision History 4.1 Version 1.0 – January 30, 2015 Original Release. No revision history.