Exhibit 9 HIT-NOT Proximity System Magnetic Field XL Generator Including Collision Avoidance Module User’s Manual v1.0 FREDERICK ENERGY PRODUCTS, LLC 1769 Jeff Road Huntsville, AL 35806 1.800.489.
Exhibit 9 Table of Contents 1. Overview………………………………………………………………………………………………………….. 2-5 1.1 Theory of Operation……………………………………………………………………………… 2 1.2 Operating Frequency….………………………………………………………………………… 2 1.3 Label Information…………………………………………………………………………………. 2-3 1.4 FCC/IC Information……………………………………………………………………….….….. 4-5 2. Operation…………………………………………………………………………………………………………. 5-8 2.1 Installation Information………………………………………………………………………… 5 2.1.1 Interoperability Warning………………………………………………………………... 5 2.
Exhibit 9 1 Overview The Magnetic Field XL Generator with Collision Avoidance Module (CAM) is part of a complete HIT-NOT Proximity Detection system from Frederick Energy Products which provides audible and visual warnings to both individuals and vehicle operators to alert them that an individual or vehicle has entered too close to an operating piece of equipment and is in a dangerous situation. The Magnetic Field XL Generator with CAM attaches directly to a vehicle or piece of machinery.
Exhibit 9 1.2 Operating Frequency The Magnetic Field XL Generator with CAM will transmit on a frequency of 73 kHz and receive on a frequency of 916.48 MHz. The Collision Avoidance Module will transmit on a frequency of 916.48 MHz and receive on a frequency of 73 kHz. The CAM is programmed not to recognize the 73 kHz from its own Generator. 1.3 Label Information The Magnetic Field XL Generator with CAM label is located on the side of the housing.
Exhibit 9 Any intentional or unintentional changes or modifications to the configuration of the Magnetic Field XL Generator not expressly approved by Frederick Energy Products LLC could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Exhibit 9 user manual for the equipment, or to be displayed on the equipment model. If more than one notice is required, the equipment model(s) to which each notice pertains should be identified. Suppliers of radio apparatus shall provide notices and user information in both English and French. This device complies with Industry Canada license-exempt RSS-standards(s).
Exhibit 9 remain where they were initially set. If the processor senses a significant power reduction, the alarm may sound for a period of time. When the sounder is activated, power must be cycled to restore normal operation. If the problem persists, then service is required. 2.4 Maintenance The Magnetic Field XL Generator with CAM should be regularly cleaned to reduce buildup of dust and dirt. The user should check to see if the LEDs are working before using the device. 2.
Exhibit 9 Transmitter Frequency: 73 kHz Operating Temperature Range: -30°C to + 55°C; -22°F to 131°F 2.8 XL Generator System Installation Guide To Be Installed By a Professional Power Cable Step 2 Step 1 Install Generator Connect to a switched and fused (5A) circuit appropriate for the 12V XL Generator or the 24V XL Generator. Install the Generator on top of the overhead guard and at least 4” (10.2cm) from the frame if placed on the counterbalance.
Exhibit 9 Field Adjust Remove the screw under the PWM arrow. Have a Pedestrian with a PAD at the desired Danger Zone limit (~34’ max.), slowly adjust the “PWM” pot with a 3/32” slotted screwdriver until the danger zone alerts at the desired distance. Return the screw • • Step 9 • Step 8 Step 7 • • • • • • Silent Zone Adjust Factory set to max. of ~22 in. or 56cm. To decrease the size, unscrew the cap from the Cab Silencer. Activate a PAD and turn on truck.
Exhibit 9 AT YOUR OWN INDEPENDENT DISCRETION AND RISK. THE HOT-NOT® SYSTEM IS NOT GUARANTEED TO PREVENT ACCIDENTS. ACCEPTANCE AND DEFINITIONS. (A) Acceptance of Terms. These Warranty Terms and Conditions (these “Terms”) are a legal agreement between You, as a purchaser and end user of the System and Frederick Energy Products, LLC. By installing the System or using the System in any way, You are (1) agreeing to be bound by these Terms.
Exhibit 9 INDEMNIFICATION; RELEASE; LIMITATION OF LIABILITY. (A) Indemnification.
Exhibit 9 confidence. No action, regardless of form, related to the obligations of the parties under this Agreement may be brought by either party against the other more than one (1) year after the cause of action has accrued. In any proceeding to enforce this Agreement, the prevailing party will have the right, in addition to its other rights hereunder, to recover its reasonable litigation costs and reasonable attorneys’ fees.
Exhibit 9 4 Revision History 4.1 Version 1.0 – June 23, 2015 Original Release. No revision history.