Product Overview

Specifications
Appearance:
Dense, paste-like consistency,
off white in color.
Content Information:
PipeFit
®
is manufactured
without asbestos in its formula.
Packaging:
16 oz. brush in cap
32 oz.
32 oz. BIC
1 gl.
5 gl.
55 gl.
CAUTION: See SDS for first
aid instructions. Wash hands
thoroughly after each use.
See Safety Data Sheet for
additional safety and disposal
information at www.fppi.com
© 2018 Smith-Cooper International. FPPI
®
and PipeFit
®
are registered trademarks of Smith-Cooper International.
FBC
™
, BlazeMaster
®
, FlowGuard Gold
®
and Corzan
®
are registered trademarks of Noveon IP Holdings Corp.
Description
Pipet
®
Thread Sealing Paste with PTFE is a premium non-hardening PTFE lled pipe thread
sealing paste designed specically for the re sprinkler industry. Pipet is suitable for use on all
threadable materials commonly used in re sprinkler systems, including CPVC. Pipet’s unique
blend of materials provides superior thread sealing qualities over other similarly priced sealants.
The particulate PTFE also helps prevent leaks by accumulating in the voids of damaged or
defective threads of the pipe or ttings. Additionally, the lubricating qualities of the PTFE and
other materials in the sealing paste improve thread seating during pipe and tting assembly.
Pipet
®
also adheres well to hot oily pipe present in “high speed’ fabrication operations.
Design Criteria/Data
Recommended Use
Water Air
Refrigerants Natural Gas
Mild caustics Steam
Kerosene LP Gases
Acids Gasoline
Diesel Fuel Ammonia
Use for threaded connections on steel,
stainless steel, aluminum, brass, PVC,
CPVC & ABS. Operating temperature
ranges -50° f to 500° f.
Installation
Make sure that the threads are free
from burs and other debris. Apply
Pipet
®
liberally to the male pipe
threads. Make sure that the thread
sealant is brushed into the “root” of
the threads. Do not wipe off excess
material until tting has been “made
on” to the pipe thread. The threading
action of the tting to the pipe will allow
the proper amount of sealant to remain
in the connection. Wipe off excess
sealant. Pipet
®
will not dry out under
normal conditions. Never use dope and
tape together. Keep covered when not
in use to avoid contamination. Some
settling of the product may occur.
Occasional stirring may be necessary.
Two year shelf life.
Disclaimer
DO NOT ALTER THE CONSISTENCY OF THIS
PRODUCT. Use as is directly from the container. Keep
away from your mouth and eyes. If eye contact occurs,
ush with water for 5 minutes. If discomfort persists get
medical attention.
The information contained herein is produced in good faith
and is believed to be reliable but is provided for guidance
and information purposes only. FPPI and its agents cannot
assume liability or responsibility for results obtained in the
use or misuse of its product by persons whose methods
and qualications are outside and beyond our control. It
is the user’s responsibility to determine the suitability of,
methods of use, preparation prior to use, and appropriate
installation for all products purchased from FPPI. It is
the user’s sole responsibility to observe and adapt such
precautions as may be advisable or necessary for the
protection of personnel and property in the handling and
use of any of our products.
WWW.FPPI.COM
PipeFit
®
Thread Sealing Paste
FBC
™
System Compatible
indicates that this product
has been tested, and is
monitored on an ongoing
basis, to assure its chemical
compatibility with FlowGuard
Gold
®
, BlazeMaster
®
and
Corzan
®
pipe and fittings.
FBC
™
, FlowGuard Gold
®
,
BlazeMaster
®
and Corzan
®
are licensed trademarks of
The Lubrizol Corporation or
its affiliates.
SMITH COOPER
COMMERCE, CA 90040
+ 1 [phone]
+ 1 [phone] FAX