Hardware Installation 3.3.2. Installing a Top Cover Follow these steps to install a top cover: 1. Align the top cover and place it on the chassis. 2. Make sure the cover hangs over the front of the server by about 1 inch (25 mm). The side latches must align with the cutouts in the chassis. Inspect both sides of the chassis making sure the top cover is fully inserted in all cutouts and ÀXVK ZLWK WKH FKDVVLV 3.
Hardware Installation 3.4. Atlas Key Modules 3.4.1. Removing an Atlas Key Module The Atlas key assembly includes the outer key and inner mating board components. 1. 2. 3. 4. Follow these steps to remove an Atlas assembly: Remove the top cover from the server. See “Removing a Top Cover” on page 10. Locate the outer Atlas key assembly on the front of the server. Turn the thumb screw to loosen the key without the mating board. Remove the assembly from the chassis. )LJXUH 5HPRYLQJ DQ $WODV .H\ 0RGXOH 5.
Hardware Installation 3.4.2. Installing an Atlas Key Module Follow these steps to install an Atlas assembly: 1. $OLJQ WKH PDWLQJ ERDUG IRU HDFK VLGH RI WKH FKDVVLV 7KH DOLJQPHQW FRQ¿JXUDWLRQ LV LQYHUWHG IRU the left and right sides. 2. Connect the cables for each mating board connector. 3. Align the mating assembly in the chassis and slide in place. Once properly installed the screw holes on the bracket and board are aligned. 4. Insert the screws and secure the board to the chassis.
Hardware Installation 3.5. NFC Modules 3.5.1. Removing a Top NFC Module Follow these steps to remove an NFC module: 1. Remove the top cover from the server, and turn it over on a clean work surface. See “Removing a Top Cover” on page 10. 2. Locate the NFC module and remove the screws. 3. Lift the module up to remove it.
Hardware Installation 3.5.2. Installing a Top NFC Module Follow the listed steps to install an NFC module. 1. Orient the the NFC module over the end of the top cover. Make sure the protruding end of the module sits over the open end of the cover. 2. Insert the screws to secure the module. )LJXUH ,QVWDOOLQJ D 7RS 1)& 0RGXOH 3. Replace the top cover on the server. See “Installing a Top Cover” on page 11.
Hardware Installation 3.5.3. Removing a Lower NFC Module Follow these steps to remove an NFC module: 1. Remove the top cover. See “Removing a Top Cover” on page 10. 2. Locate the lower NFC module at the rearside of the server. 3. Locate the FFC connected to the NFC module and rotate the locking lever to the open position. )LJXUH 'LVFRQQHFWLQJ DQ ))& &DEOH Once the FFC cable is disconnected, the NFC reader and NFC module can be removed.
Hardware Installation f Lift the module up to remove it. )LJXUH 5HPRYLQJ D /RZHU 1)& 0RGXOH To remove the NFC reader: f Grasp the reader by the end, making sure to avoid holding or applying pressure to the FFC cable. Do not hold on to the FFC cable to avoid damaging it. )LJXUH 5HPRYLQJ DQ 1)& 5HDGHU f Once the reader is removed, turn it around and rotate the locking lever to the open position.
Hardware Installation f Disconnect the FFC cable for use during the installation of the new NFC reader.
Hardware Installation 3.5.4. Installing a Lower NFC Module Follow the listed steps to install an NFC module. 1. Locate the rear of the chassis to position the NFC outer cover. 2. Align the cover over the enclosure. Make sure the screw holes on the enclosure and cover are properly aligned. 3. Secure the cover with the provided screws. )LJXUH ,QVWDOOLQJ DQ 1)& &RYHU 4. Grasp the NFC module by the ends and place on a clean work surface. 5.
Hardware Installation Repeat for the remaining FFC cable if necessary. )LJXUH ,QVWDOOLQJ DQ ))& &DEOH 9. 2QFH WKH ))& FDEOH LV VHFXUHG JUDVS WKH PRGXOH E\ WKH HQGV DQG ÀLS LW RYHU WR SRVLWLRQ LW WR install the NFC reader. 10. Position the NFC reader with the adhesive pads up to align it with the open end of the FFC cable. 11. Open the locking lever on the reader and insert the FFC cable. )LJXUH &RQQHFWLQJ DQ 1)& 0RGXOH DQG ))& &DEOH 12.
Hardware Installation 14. Insert a screw on the right side to secure the NFC card to the cover. )LJXUH ,QVWDOOLQJ DQ 1)& 0RGXOH 15. Grasp the ground cable and position it over the remaining screw hole and insert a screw to secure it and the moudle to the cover. If necessary, secure the other end of the ground cable to the enclsoure.
Hardware Installation Once the module is secured, locate the adhesive cover on the NFC reader and remove it. )LJXUH 5HPRYLQJ WKH $GKHVLYH &RYHU 17. %HIRUH LQVWDOOLQJ PDNH VXUH WKH ))& LV ÀDW DQG VWUDLJKWHQHG RXW RYHU WKH FRYHU 7KHQ OD\ WKH reader down starting from the FFC side. )LJXUH ,QVWDOOLQJ DQ 1)& 5HDGHU Replace the top cover on the server. See “Installing a Top Cover” on page 11.
Hardware Installation 3.5.5. Installing a Standalone NFC Reader Follow the listed steps to install an NFC reader. 1. Locate the rear of the chassis and the installed NFC module. 2. Locate the locking lever on the NFC connector and gently rotate it to the open position to expose the contact points. 3. Align the FFC cable with the module connector. Make sure the blue strip faces upwards when inserted into the connector. 4. Lower the locking lever over the FFC cable to lock it.
Hardware Installation 7. Secure the cover with the provided screws. )LJXUH ,QVWDOOLQJ DQ 1)& 5HDGHU Replace the top cover on the server. See “Installing a Top Cover” on page 11.
Hardware Installation 3.6. Panel Mounts 3.6.1. Removing a Busbar Follow these steps to remove a busbar cable: 1. Remove the top cover from the server. See “Removing a Top Cover” on page 10. 2. From the rear side, locate the busbar clip and remove the screws and washers securing it to the server. 3. Pull out the busbar clip and remove it from the enclosure. )LJXUH 5HPRYLQJ D %XVEDU 3.6.2. Installing a Busbar Follow these steps to install a busbar: 1.
Hardware Installation 3. Secure it to the chassis with the provided screws. )LJXUH ,QVWDOOLQJ D %XVEDU 4. Install the top cover on the server. See “Installing a Top Cover” on page 11. 3.6.3. Removing a Panel Mount 1. 2. 3. 4. Follow these steps to remove a power distribution board: Remove the top cover from the server. See “Removing a Top Cover” on page 10. Remove the PDB. See “Removing a Power Distribution Board” on page 37. Remove the securing screws to release the panel mount.
Hardware Installation Pull the module out of the bracket.
Hardware Installation 3.6.4. Installing a Panel Mount Follow these steps to remove a power distribution board: 1. Align the panel mount with the bracket. Ensure the marking on the module is correctly positioned with the correlating slit on the bracket. )LJXUH $VVHPEOLQJ D 3DQHO 0RXQW 2. Insert the module in the bracket and slide it to the locking position. 3. Align the panel assembly over the location on the chassis. Make sure the connectors are facing LQWHUQDOO\ WR FRQQHFW ZLWK WKH 3'% )LJXUH
Hardware Installation 4. Insert the securing screws to lock the panel assembly to the chassis. )LJXUH ,QVWDOOLQJ D 3DQHO 0RXQW 5. Connect the power distribution board. See Install the 2.5” SATA SSD assembly. See “Installing a 2.5” SATA SSD Assembly” on page 31. 7. Replace the top cover on the server. See “Installing a Top Cover” on page 11.