Hardware Installation 3.7. Storage 3.7.1. Storage Cable Routing CBL_SATA Power Cable (Amphenol :RST15-1051) CBL_SATA Signal Cable (Amphenol :RST07-3144) )LJXUH 6WRUDJH &DEOH 5RXWLQJ 3.7.2. Removing a 2.5” SATA SSD Assembly Follow these steps to remove a 2.5” SATA SSD assembly: 1. Remove the top cover from the server. See “Removing a Top Cover” on page 10. 2. Loosen the thumb screw securing the SATA SSD assembly.
Hardware Installation 3. Slide the SATA SSD assembly to release and remove it from the server. )LJXUH 5HPRYLQJ D ´ 6$7$ 66' $VVHPEO\ 3.7.3. Installing a 2.5” SATA SSD Assembly Follow these steps to install a 2.5” SATA SSD assembly: 1. Connect the cables to the SATA SSD assembly. See “Storage Cable Routing” on page 30. 2. Align the keyhole on the SATA SSD assembly and slide in place. 3. Secure the SATA SSD assembly with a thumb screw. )LJXUH ,QVWDOOLQJ D ´ 6$7$ 66' $VVHPEO\ 4.
Hardware Installation 3.7.4. Removing an 2.5” SATA SSD Follow these steps to remove a 2.5” SATA SSD: 1. Remove the top cover from the server. See “3.3.1. Removing a Top Cover” on page 32. 2. Remove the 2.5” SATA SSD assembly. See “Removing a 2.5” SATA SSD Assembly” on page 30. 3. Disconnect the cables from the SATA SSD assembly. See “Storage Cable Routing” on page 30. 4. Push the release latches and pull the SATA SSD assembly out of the cage. )LJXUH 5HPRYLQJ D ´ 6$7$ 66' $VVHPEO\ 5.
Hardware Installation 3.7.5. Installing a 2.5” SATA SSD Follow these steps to install a 2.5” SATA SSD: 1. 3RVLWLRQ WKH UHDU RI WKH 66' ZLWK WKH 66' KROGHU VHH WKH IROORZLQJ ¿JXUH 7KH VOLWV RQ WKH DUPV of the holder must be positioned upwards in a proper installation. 2. Pull back the ends of the SSD holder and insert the SSD until the retaining pins on the holder are inserted in the screw holes of the SSD. )LJXUH ,QVWDOOLQJ D ´ 6$7$ 66' 3.
Hardware Installation 3.8. System Fans 3.8.1. Fan Cable Routing 4 3 2 1 4 3 2 1 CBL_ an power ignal Cable (7 pin) (Amphenol : R - 0 ) )LJXUH )DQ &DEOH 5RXWLQJ 3.8.2. Removing a System Fan Follow these steps to remove a system fan: 1. Remove the top cover from the server. See “Removing a Top Cover” on page 10. 2. Disconnect the fan cables from the mainboard. See “Fan Cable Routing” on page 34. 3. Remove the fan. )LJXUH 5HPRYLQJ D )DQ 0RGXOH 4.
Hardware Installation 5. Pull out the outer fan rivets securing the bumper. Remove the fan guard from the fan module. 7. Pull out the inner rivets from the fan module. )LJXUH 'LVDVVHPEOLQJ D )DQ 0RGXOH Repeat the steps for the remaining fans. 3.8.3. Installing a System Fan CAUTION: 0DNH VXUH WKH DLUÀRZ DUURZV RQ WKH V\VWHP IDQ DUH SRLQWLQJ WRZDUGV WKH UHDU RI WKH V\VWHP WR SUHYHQW V\VWHP RYHUKHDWLQJ 1. 2. 3. 4. 5.
Hardware Installation 7. Insert the cable through the fan cage and lower the rubber brackets on the ends of the fan into the slot reserved for the rubber bracket. If it is necessary pull the power cable to tighten the slack. )LJXUH ,QVWDOOLQJ D )DQ $VVHPEO\ Repeat the steps for the remaining fans. 9. Connect the fan cables to the mainboard. See “Fan Cable Routing” on page 34. 10. Replace the top cover on the server. See “Installing a Top Cover” on page 11.
Hardware Installation 3.9. Power Distribution Boards 3.9.1. Removing a Power Distribution Board Follow these steps to remove a power distribution board: 1. Remove the top cover from the server. See “Removing a Top Cover” on page 10. 2. If installed, remove the 2.5” SATA SSD assembly. See “Removing a 2.5” SATA SSD Assembly” on page 30. 3. Disconnect the cables from the power distribution board. 4. Remove the screws securing the power distribution board. 5. Remove the power distribution board.
Hardware Installation 3.9.2. Installing a Power Distribution Board Follow these steps to install a power distribution board: 1. Align the power distribution board over the tray. 2. Lower the PDB and slide it into the panel mount clip. 3. Secure the PDB with the provided screws. )LJXUH ,QVWDOOLQJ D 3RZHU 'LVWULEXWLRQ %RDUG 4. Connect the cables to the power distribution board. 5. Install the 2.5” SATA SSD assembly. See “Installing a 2.5” SATA SSD Assembly” on page 31.
Hardware Installation 3.10. Interposer Assemblies 3.10.1. Removing an Interposer Assembly Follow these steps to remove an interposer assembly: 1. Remove the top cover from the server. See “Removing a Top Cover” on page 10. 2. Gently lift the air duct out of the chassis. )LJXUH 5HPRYLQJ D . & $% $LU 'XFW 3. Disconnect the cables from the interposer assembly.
Hardware Installation 4. Remove the screw securing the interposer assembly. 5. Slide the interposer assembly to unlock from the posts. Remove the interposer assembly. )LJXUH 5HPRYLQJ DQ ,QWHUSRVHU $VVHPEO\ 40
Hardware Installation 3.10.2. Installing an Interposer Assembly Follow these steps to install an interposer assembly: 1. Align the interposer assembly with the posts in the chassis. 2. Install the interposer assembly and slide in place to lock the assembly with the posts. 3. Secure the interposer assembly with the screw. )LJXUH ,QVWDOOLQJ DQ ,QWHUSRVHU $VVHPEO\ 4. Connect the cables to the interposer assembly.
