COMPANY CONFIDENTIAL REV 0.7 LTE PCI Express M.2 Module 95.1993T01 User Manual version 0.
COMPANY CONFIDENTIAL REV 0.7 Table of Contents 1. INTRODUCTION ................................................................................................................................................... - 3 1.1 SCOPE ............................................................................................................................................................... - 3 1.2 FUNCTION..............................................................................................................
COMPANY CONFIDENTIAL REV 0.7 1. Introduction Project Name: LTE PCI Express M.2 Module Foxconn Project Code: 95.1993T01 This documentation describes the hardware, and mechanical requirements specification of LTE PCI Express M.2 Module. It is a confidential document of Foxconn. 1.1 Scope The function of this module provides a LTE wireless WAN interface to access the internet, and it is fully compliant with LTE specification (3GPP Release 12). 1.
COMPANY CONFIDENTIAL REV 0.7 2. Specification 2.1 Physical Interface RGMII, PCI express M.2 module, PCB size: 64.4 mm x 65 mm Antenna connector: UFL connector *8 Dual SIM interface (one for testing) 2.2 Pin Arrangement Figure 2.1 the sequence of pins on the 75-pin signal interface of M.2 Key.B.
COMPANY CONFIDENTIAL REV 0.7 13 NA NA NA NA 14 NA NA NA NA 15 NA NA NA NA 16 NA NA NA NA 17 NA NA NA NA 18 NA NA NA NA 19 NA NA NA NA 20 SIM1_RST_O Test SIM reset Output SIM1 VCC 21 GND ground NA NA 22 SIM1_CLK_O Test SIM clock Output SIM1 VCC 23 UART0_RXD UART0 serial receive data Input 1.8V 24 SIM1_DAT_O Test SIM data Bi-Direction SIM1 VCC 25 UART0_TXD UART0 serial transmit data Output 1.
COMPANY CONFIDENTIAL REV 0.7 51 GND ground NA NA 52 NA NA NA floating 53 GPD2_1 GPIO for future use NA 1.8V 54 RGMII_RXD3 RGMII Interface Input 1.8V 55 GPD2_2 GPIO for future use NA 1.8V 56 RGMII_RXD2 RGMII Interface Input 1.8V 57 GND ground NA NA 58 RGMII_RXD1 RGMII Interface Input 1.8V 59 GPD2_3 GPIO for future use NA 1.8V 60 RGMII_RXD0 RGMII Interface Input 1.8V 61 GPD2_4 GPIO for future use NA 1.8V 62 RGMII_TXD3 RGMII Interface Output 1.
COMPANY CONFIDENTIAL REV 0.7 LTE Features:(Internal: 4Rx-2TX; External: 4Rx-2TX) 8RX Diversity TDD/FDD 3.1.2 RF transceiver: GRF7243A GRF7243A is a fully integrated RF transceiver, all required PLL/VCO/loop filters are integrated. Patented direct-conversion RF architecture with CMOS integration and minimizing external BOM cost. Supports all LTE bandwidth with multiple bandwidth channel selection filter 5/10/15/20MHz RX saw-less architecture except UHB TX single-ended port except UHB 3.1.
COMPANY CONFIDENTIAL REV 0.7 3.1.6 USIM Off-board USIM connector supported. This module provides the dual SIM interface, and it can be selected by SIM_SEL pin (the pin 1 of M.2 connector). SIM_SEL(internally pull up) State High Low SIM selection SIM0 SIM1 3.1.7 RF CONNECTOR Figure 3.
COMPANY CONFIDENTIAL REV 0.7 Figure 3.
COMPANY CONFIDENTIAL REV 0.
COMPANY CONFIDENTIAL REV 0.7 3.2 Mechanical Specifications 3.2.1 Overview The golden finger of 95.1993T01 is compatible with the NGFF 75 pin card edge-type connector. Refer to NGFF Electromechanical Specification Revision P12 with Input Power and Voltage Tolerance ECN for more details. 3.2.2 Mechanical constraints Figure 3.3 Shows the mechanical constraints of 95.1993T01 3.
COMPANY CONFIDENTIAL REV 0.7 3. Need implement thermal solution on Platform (Example: add thermal pad to heat dissipated from LTE module to Platform PCB) would get more thermal margin and benefit then extend the operating temperature 4. Operating 95.1993T01 device under conditions beyond its absolute maximum ratings (Table 3-1) may damage the device. Absolute maximum ratings are limiting values to be considered individually when all other parameters are within their specified operating ranges.
COMPANY CONFIDENTIAL REV 0.7 OEM/Integrators Installation Manual Important Notice to OEM integrators 1. This module is limited to OEM installation ONLY. 2. This module is limited to installation in mobile or fixed applications, according to Part 2.1091(b). 3. The separate approval is required for all other operating configurations, including portable configurations with respect to Part 2.1093 and different antenna configurations 4. For FCC Part 15.
COMPANY CONFIDENTIAL REV 0.7 with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.
