User Manual

ManualsBrandsFossil Group ManualsElectronicsMetaWatch - Analog

Bluetooth Watch User Manual Draft

Watch Firmware v0.7.15

Android APK v0.1.9b

Getting Started

Starting the Watches

Charge your watch. Attaching the clip may cause the watch to reset. This is only for Beta units.

It is due to the Reset pin used for 2-wire JTAG (embedded debugging) being turned ON by

default.

Resetting the watch causes pairing information to be deleted. This (pairing information) will be

stored in Flash memory in the next revision of software. If you reset while paired, be prepared

for a new pairing request.

If you are using a large grey charge clip that has an 18 pin ribbon connector on the back, you

should attach your clip to the watch BEFORE applying power via the micro USB socket.

If you are using the small black clip with only a micro USB socket, then you should be able to

attach to the watch however you like. It may be possible to short the power against the steel

case back; there are protections in place to limit any damage, but you may notice the clip

getting hot if this occurs. Try to verify that everything is seated correctly and that the watch is

charging.

Digital Watch

There are 6 buttons on the digital watch. When booted the digital watch has these functions

(mostly for demonstration and debug). The watch boots in a “radio mode”.

MetaWatch.org User Manual Draft APK v0.1.9b

Watch v0.7.15

Summary of content (9 pages)

PAGE 1
Bluetooth Watch User Manual Draft Watch Firmware v0.7.15 Android APK v0.1.9b Getting Started Starting the Watches Charge your watch. Attaching the clip may cause the watch to reset. This is only for Beta units. It is due to the Reset pin used for 2-wire JTAG (embedded debugging) being turned ON by default. Resetting the watch causes pairing information to be deleted. This (pairing information) will be stored in Flash memory in the next revision of software.
PAGE 2
Analog Watch There are 3 buttons on the Analog watch. When booted the analog watch has no UI functions. MetaWatch.org User Manual Draft Watch v0.7.
PAGE 3
This is a temporary situation. There will be a default analog watch UI similar to the digital watch UI. Starting the Android APK (Meta Watch app) Enable 3rd party app installation from Unknown Sources; this check box is found in Settings>Applications on Nexus S OS 2.3. The APK file can be installed by installing from a GMAIL account or by loading on the SD card via USB and then browsing for the file using a file manager application. We use Astro File Manager.
PAGE 4
1) Make sure the watch is charged and the radio is ON. (For analog, you may need to reset the watch to ensure the radio is on) -- Right now, the watch will stay ON with no connection for 10 minutes. After that, it will turn OFF and you will need to start it again. 2) In the App, hit Menu->Settings->Select Watch 3) Select your watch from the menu. The name of the watch should include “Fossil” and “Analog” or “Digital”. You should make sure the MAC address matches if there is more than one watch around.
PAGE 5
If you have had a big enough software crash (usually associated with phone’s that misbehave), then you may need to wait for the batteries to run out if all else fails. You can connect to the USB debugger and send a reset signal. Let me know if you need that. Connecting the charger can cause a reset at the moment (because of a debugging signal that’s on) There is a way to remove and reinsert the battery. Let me know if you need that.
PAGE 6
Samsung Galaxy S HTC Evo Samsung Infuse Droid X Contact David Rosales drosales@fossil.com mobile:+1.214.704.4218 @davidro MetaWatch.org User Manual Draft Watch v0.7.
PAGE 7
Product Information for WDS111 and WDS112 FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
PAGE 8
gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. This Device complies with Industry Canada License-exempt RSS standard(s). Operation is subject to the following two conditions: 1) this device may not cause interference, and 2) this device must accept any interference, including interference that may cause undesired operation of the device.
PAGE 9
Bluetooth® Statement This product contains QDID B015490 and QDID B016770. The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Fossil Partners, L.P. under license. Other trademarks and trade names are those of their respective owners.