GPSmart Manual 一、Main Function Introduction ﹙ 1 ﹚ SATELLITES ﹙ 2 ﹚ POSITION ﹙ 3 ﹚ NAVIGATION ﹙ 4 ﹚ ROUTE ﹙ 5 ﹚ GO TO ﹙ 6 ﹚ MAP ﹙ 7 ﹚ AREA ALCULATE ﹙ 8 ﹚ DATA BASE ﹙ 9 ﹚ SETUP ( 10) BLUETOOTH (Only for Bluetooth version) Attention: Bluetooth item of operation is only for Bluetooth version. Bluetooth version Without Bluetooth version 二、The operation mode and instruction. The mode has four buttons. Power: Power switch. Back light button: Use it at night or darkness. Enter button: Enter function.
三、Instruction of main function After pushing power, it will display company logo. Then push next or enter, it will turn to main function. Step 1: Satellite Distribution: Step 2: Display Route. Step 3: Route Function Step 4: Manu Selection Press up or down button for continuing three times, it will turn into main function.
User’s Movement=> Map Function=> Menu Turn off power switch as long as push power again. (1) Satellite Distribution and Satellite Intensity In the menu, pressing the next and choosing “ SATELLITES”. Then, the screen will display satellite distribution and single intensity. As long as pushing enter again, it will come back to main function. The function only indicates satellite signal condition.
=> Satellite Distribution The two circle of above half screen is satellite distribution. There are two circles of the graph; the big one indicates horizon and the other indicates to turn upward 45 degree. The center indicates zenith, such as ninety degree of elevation. There is an “N” in the big circle side; it indicates the North. There are several squares of the big circle; they indicate satellites. The inner number of squares is satellite serial number.
=> Position 2-1 The square of screen indicates position at present. There are four items of Latitude. The first means north latitude and south latitude. The second, third, and forth are degree, minute and second. One degree= 60 minutes, One minute= 60 seconds. The coordinate system value is WGS84 (GPS) or GSR80 (TWD97). Please pay attention if you use another map.
=> 3-2.Select Function : 3-2-1 Push up or down bottom to select "SPEED"," LOCATION"," LOCAL TIME"," ALTITUDE" and "ELAPSE".
Local Time<=> Elapse <=>Return “Speed”. 3-2-2 It provides different choices depend on function. Speed: Change speed unit to MI/H <-> KM/H Exit => Now Position: Change location unit to degree <-> degree、minute and second.
=> Latitude:Change latitude unit to FT <-> M => Local Time: Change time unit to 24 H <-> 12 H Exit => Elapse: Record item ; Exit ; START,CLEAR <=> STOP
=> Or => ﹙ 4﹚ Display Route The function can record your route point, when you go to uncertain place. After you arrive at destination, it can guide user come back to the starting place. => 4-1.
=> Select route file and enter it, it will display sub selections. #### =====> The sub selections are: A.SELECT : => Select route. B.RENAME : Rename route name. C.DELETE : Delete route data. D.CANCEL : Cancel and select another route. The 20 set of route are available. There are four pages, and each page has 5 sets. Attention: The 20 set route can use area calculate function.
=> 4-2-1.Display-route trace. 4-2-2 Push up or down button can change scale. 4-2-3.Push enter button to exit and return to “Route” function. => 4-3 Route View Mode Use the function to view past route trace.
4-3-2 Set route dots of “EVERY STEP” 4-3-3 Display Trace It will add trace dots as long as you push up down button. It will delete trace dots as long as you push up button. Because the screen use trace point as central point, user’s position may beyond range. If user beyond range, it will use triangle to indicate user’s position. As fellow, user stands on right side of triangle and the distance is uncertain.
4-3-4 View Option => 在顯示航跡途中按下決定鍵,隨即顯示航跡觀察選項。可設定將地圖拉 近、拉遠或者跳出此模式並回到航跡主選單。 4-4 Set Time Interval It indicates time interval of route. Ten seconds => Thirty seconds => One minute => Five minutes => Ten minutes => Thirty minutes => Ten seconds => 4-5 Start Record After enter “ START REC”, you can view moving direction and route.
4-5-1. After you push “START REC” item, it will start to record. It can view your moving direction and your route. 4-5-2.Push up or down button can view user’s information, for example, now position, time and recording time.
Elapse 4-5-3.按決定鍵開啟子功能選項,可選擇 [ 繼續、地圖放大、地圖縮小、 增加路徑點、記錄時間操作模式、清除記錄時間、停止 ] 等功 能。 4-5-3 Push enter to sub selection, you can choose “CONTINUE”, “ZOOM IN”, “ ZOOM OUT”, “ ADD WAY PT”, “ELAPSE” AND “ STOP”.
Turn on Elapse Delete Elapse Turn off Elapse Stop “ADD WAY PT.” operation mode is as the same as “ADD MARK”, please refer to “ DISPLAY MAP”. If satellite is not fixed, user cannot save data. User must go to spacious place until the signal is fixed. Way Point can only be saved when the GPS is Fixed.
4-6 Exit (5) Display Target, Generally Position. Display the north. In the main function, push up or down to “ Go To”. It guides target direction and distance.
5-1-1 Instruction of the central icon Solid Triangle: Heading Circle: It indicates compass. Arrow Head:The direction to target, if Arrow Head indicates up,it means target is in front of user. Arrow Head show down,it means target is back to user. Arrow Head indicates right, it means target is in user’s right side. Arrow Head indicates left, it indicates target is in users left side.
距離若是低於 10 公里(6 英哩),則距離 單位會顯示公尺(英呎)。若是高於 10 公里(6 英 哩),則距離單位會顯示公里(英哩)。 速度 : 顯示使用者目前的速度。 Now Position<=> Elapse<=> Speed Local Time<=> Distance<=>
<=> Return to "NOW POSITION" 5-2-2 Push enter to select “ TARGET”, “ TIME RECORD”, and “ EXIT” function. 5-2-2-1 There are three selections of “ TARGET” function: <1> WAY POINT => Target display way point data of route.
=> => The mark data within now position’s scale is 20KM*30KM and it doesn’t display and change mark beyond 20KM*30KM. <3> INPUT POSIT. In the function, user can directly input position to be target. => => 5-2 Push up and down to select “ TIME RECORD”. After push enter, you can manage it in “ ELAPSE” function. If “ TIME RECORD” function stop, the screen will display “ START” and “ DELETE” selections.
“ELAPSE” selection. => If it is recording time, the screen will display “ STOP” selection. => 5-3 Push “ EXIT” to return main function. ﹙ 6﹚ Display Map 6-1.Instruction: User’s position is a blinking icon. It will change to another page when user moves beyond the screen. => 6-2.Operation: 6-2-1Push up or down to gain information.
Position、 、 、 Altitude Speed Local Time、 6-2-2 Push enter to sub selection.
6-2-2-2 Zoom Out :Narrow down 6-2-2-3 Add Mark :Add Mark within 10 kilometers => There are five selections: <1>、SAVE DATA ? Select the “ADD MARK” and push enter botton, it will display confirm window. If you choose “YES”, it will save data in the memory. If you choose “NO”, it will exit and come back to “ADD MARK”.
=> <2>FLAG Enter the function can select type icon. The icon indicates mark. => <3>、MARK NAME Enter the “ MARK NAME” can set mark name. <3-1> >> Enter “ MARK NAME” to set up mark name. <3-2>Alphabet Category: Select alphabet. <3-3> Enter Choose mark name and return Mark name to make a list. <3-4> Exit Exit and return to “ ADD MARK”.
=> Set Mark Name <4>、POSITION VALUE In the “ POSITION VALUE” can set mark position. => Set Mark Position There are four selections.
As long as it is in “LON” or “LAT” item and push enter bottom, you can set up. N, S or E, W Degree Minute' Second'' Push up or down to exit. It will exit to “ SET NUMBER” as long as you set number selection.
<5> EXIT Select “ Exit” function will return to main function without saving data. 6-2-2-4 Delete Mark:Delete mark within 10 kilometers. => In “ DELETE MARK” function, it will display mark list within ten kilometers. You can select any of the “MARK” to delete. 6-2-2-5 Elapse :Turn on “ ELAPSE” Turn off :Exit “ ELAPSE” 6-2-2-6 Exit (7) Area Calculate “ Area Calculate ” way should around area fringes, and then it will calculate approximately area.
#### =====> => 7-1 Area Calculate 7-1-1 START After it clear the 20 set route data, it will start to record route. As follow: Push up or down to change scale. Push enter will display total area.
In the record mode, push up or down to change scale. Push enter will display total area amount. Change calculate unit: The unit is meter square. (SQ.M) or kilometer square (SQ. KM). English unit is foot square (SQ. FT) or mile squire (SQ. MI) or acre( ACRE). Continue: Continue “ AREA CALCULATE“ mode. Exit: Exit “AREA CALCULATE” mode. 7-1-2 Continue to Calculate Continue calculate last area. The operation is the same as “ 7-1-1 START ”.
7-1-3 Set Unit Change area unit, the area have: A. SQ. M (SQ. KM ) B. SQ. FT(SQ. MI ) C. ACRE 7-1-4 Area Trace The map will change new page if user beyond screen.
7-1-5 Area View Recall last area data and display area. => => Push enter to change map scale or return to main function.
﹙ 8﹚ Manage Data Base Select “ DATA BASE” in the main function. There are three selections in the function: => 8-1、 ROUTE => => This sub selection: Select route: Select route. Rename:Rename route. Delete:Delete route. Chancel:Exit and select another route.
=> Map function only can delete mark. 8-3、EXIT ﹙ 9﹚ Operation Select “ SETUP” function in menu. There are three selections. => 9-1、TIME ZONE Each time interval is (1 hour). There are four sub selections.
=> For Example:Australia=> +10 h,German=> +1 h America Los Angles =>-8 h 9-2、MIRROR DISP => Select the function to display mirror image.
“ CLEAN MEMORY” will clear data, please use be caution. 9-5、EXIT ﹙ 10﹚ Transfer Bluetooth wireless data ( Only for Bluetooth version) 10-1 Instruction: Turn on “ BLUETOOTH”, you can transfer NMEA data to another bluetooth machinevia wireless. 10-2 Turn on Bluetooth wireless transfer system.
10-3 Turn off Bluetooth wireless transfer system. => => 三、Attention (1) User gain correct value as long as satellite lock. Please refer to “3D” or “2D” in the right side of screen. If it doesn’t display “3D” or “2D” ( As follow), restart the machine and observe again. (2Local Time means Greenwich Mean Time add time zone offset. code can adjust from main function “SETUP”. (3 It indicates satellite intensity and user’s position lock. It indicates unlock user’s position.
=> (5) The coordinate of machine indicate WGS84(GPS) or GR80 (TWD97). Please pay attention. FCC Notices This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2)This device must accept any interference received, including interference that may cause undesired operation .