ES820 Secure Wireless Bridge Hardware Guide www.fortresstech.
ES820 Bridge Fortress ES820 Secure Wireless Bridge ES820 [rev.1] 009-00025-00r1 Copyright © 2010 Fortress Technologies, Inc. All rights reserved. This document contains proprietary information protected by copyright. No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, without written permission of Fortress Technologies, 4023 Tampa Road, Suite 2000, Oldsmar, FL 34677, except as specified in the Product Warranty and License Terms.
ES820 Bridge YOU MAY ALSO FIND HELPFUL THE FOLLOWING BOOKLET, PREPARED BY THE FCC: “HOW TO IDENTIFY AND RESOLVE RADIOTV INTERFERENCE PROBLEMS.” THIS BOOKLET IS AVAILABLE FROM THE U.S. GOVERNMENT PRINTING OFFICE, WASHINGTON, D.C. 20402 CHANGES AND MODIFICATIONS NOT EXPRESSLY APPROVED BY THE MANUFACTURER OR REGISTRANT OF THIS EQUIPMENT CAN VOID YOUR AUTHORITY TO OPERATE THIS EQUIPMENT UNDER FEDERAL COMMUNICATIONS COMMISSION RULES.
ES820 Bridge Table of Contents Port Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Chassis and I/O Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Radios . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37-Pin Input/Output Connector . . . . . . . . . . . . . . . . . . . . . . . .
ES820 Bridge: Hardware 1 Port Locations The ES820 Bridge’s power inlet, input/output control connector, and antenna ports are located on the back panel, shown below. antenna port Radio 2 DC power inlet I/O control connector antenna port Radio 1 Figure 1 2 ES820 Back-Panel Port Locations LED Indicators The ES820 Bridge’s front panel features six system LEDs.
ES820 Bridge: Hardware Radio1 color green solid green - Radio is on. intermittent green - Radio is passing traffic. off - Radio is off or Bridge’s RF Kill function is enabled.
ES820 Bridge: Hardware 5 37-Pin Input/Output Connector The connector on the rear panel of the ES820 provides all nonradio input/output for the unit. In order to connect to the ES820, a cable with a matching connector must be made, using the required to connector type: Amphenol MILDTL-D38999 / 26MD35PN 1 21 31 11 Figure 3. MIL-DTL-38999 Series III TV Shell/Insert 15-35 (socket) Table 1 defines the pin-out required for the ES820 cable connector. Most definitions are standard (ex.
ES820 Bridge: Hardware when the zeroize is pressed, the function is executed as soon as power is applied. This pin would commonly be tied to a push button. The 37-pin connector provides support for six LEDs, five controls, two Ethernet ports, one USB port, and one RS232 COM port. Table 1.
ES820 Bridge: Hardware 6 3-Pin DC Input Connector The Bridge uses a 3-pin connector to input power. C A B Figure 4 3-pin Power Connector Pins Table 2 shows the power connector pin-outs. Table 2. ES820 DC Power Connector Pin-Outs pin 7 signal A +9 to 30 VDC B N/C C GND Dimensions and Weight dimension inches centimeters height 1.75 4.44 width 6.85 17.4 depth 7.29 18.52 The ES820 weighs 2 lbs 8 oz (1.13 kg).