User Manual WMIQ-287ACN Version: 1.
5GHz+2.4G 802.11b/g/n/ac/n/a 1.3Gbps(5G)+450Mbps(2.4G) WMIQ-287ACN is a 5Ghz +2.4G dual Band selectable 3T3R PCIe mini Card Module based on the Qualcomm QCA9880 solution which features improved transmission power and sensitivity by Gemtek. Using the QCA9880 external FEM, it is the ideal cost effective solution for platform integration. With enhanced technologies such as advanced power management and receiver boost, it makes the WMIQ-287ACN the ideal 5Ghz+2.4G 3T3R module.
20MHz channel: 1Nss: 65Mbps @ 800GI, 72.2Mbps @ 400GI (Max.) 2Nss: 130Mbps @ 800GI, 144.4Mbps @ 400GI (Max.) 3Nss: 195Mbps @ 800GI, 216.7Mbps @ 400GI (Max.) 40MHz channel: 1Nss: 135Mbps @ 800GI, 150Mbps @ 400GI (Max.) 2Nss: 270Mbps @ 800GI, 300Mbps @ 400GI (Max.) 3Nss: 405Mbps @ 800GI, 450Mbps @ 400GI (Max.) 802.11ac: 20MHz channel: 1Nss: 78Mbps @ 800GI, 86.7Mbps @ 400GI (Max.) 2Nss: 156Mbps @ 800GI, 173.3Mbps @ 400GI (Max.) 3Nss: 260Mbps @ 800GI, 288.9Mbps @ 400GI (Max.
RF Spec Frequency Range 2.4G,5G Radio Stream 3T3R Transmit Power (Per Radio Stream) Tolerance ( +/- 2dBm) 802.11b 1Mbps 19 dBm 802.11g 6Mbps:18 dBm 802.11n HT-20 MCS0 :18 dBm 802.11n HT-40 MCS0 :12 dBm 802.11a 6Mbps: 19 dBm 802.11n HT20 MCS0: 18dBm 802.11n HT40 MCS0: 18dBm 802.11ac VHT20 MCS0: 18dBm 802.11ac VHT40 MCS0: 18dBm 802.
Dimension: 51mm * 30mm (full size)
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Country Code selection feature to be disabled for products marketed to the US/CANADA. Operation of this device is restricted to indoor use only. This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna, 3) For all products market in US, OEM has to limit the operation channels in CH1 to CH11 for 2.
Industry Canada statement This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme aux CNR exemptes de licence d'Industrie Canada.
This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed.
End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains IC: 7280B-130523 ”.
This radio transmitter (IC: 7280B-130523 ) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device Cet émetteur radio (IC: 7280B-130523 ) a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous avec le gain maximal admissible indiqué.