FortiCam CD51 QuickStart Guide forticam-CD51.
July 6, 2021 1st Edition Copyright © 2021 Fortinet, Inc. All rights reserved. Fortinet®, FortiGate®, FortiCare® and FortiGuard®, and certain other marks are registered trademarks of Fortinet, Inc., and other Fortinet names herein may also be registered and/or common law trademarks of Fortinet. All other product or company names may be trademarks of their respective owners.
Table of Contents Package Contents 4 Hardware Installation 5 Mounting Plate Details 12 Status LED Explanation 14 Camera Connection 15 Technical Specifications 17 Register for Support 19 Cautions and Warnings 20 Regulatory Notices 21 forticam-CD51.
Package Contents Camera Box Accessory Box • • • • • • • • • FortiCam camera QSG EMT adapter Mounting plate Replacement dry pack • • Torx T10 allen key Waterproof connection kit Grounding kit Machine bolt kit • 4x M4 bolts (M4x10mm) Screw and plug kit • 2x short screw (4x20mm) • 2x long screw (4x32mm) • 2x anchors T-bar mount kit • 2x 3/4” clips • 2x 1” clips • 2x M3 bolts (M3x16mm) • 2x M3 nuts Page 4 forticam-CD51.
Hardware Installation • Before installing surveillance cameras, design your system carefully and verify the location and coverage of each camera. Additionally, decide whether to run the cables through the wall/ceiling (drilling required) or along the wall/ceiling through the cable notch on the base. • Install the camera in a protected location that is not easily accessible, and is away from impacts or heavy vibrations.
There are multiple ways to install the CD51 camera. To determine your optimal installation method, consult the Mounting Guide. The following procedure demonstrates installing the camera on the wall or ceiling using the standard mounting procedure: Important: Only remove the protective wrap from the camera lens when the entire installation process is completed to avoid damage and scratches.
2. 3. 4. Drill holes at the marked positions and use the supplied plugs and screws to attach the mounting plate to the surface. Remove the small cover at the side of the camera if the cable is not fed through a hole in the wall or ceiling. If using Electro Mechanical Tubing, attach the EMT adapter to the mounting plate with the two M3 nuts supplied in the T-bar mounting kit. Install the ¾” EMT conduit to the camera location and attach it to the EMT adapter.
5. Assemble the waterproof connector onto the Ethernet cable. 6. Connect the Ethernet cable. The cable can be stored in the EMT tubing or in the hole in the wall or ceiling. OR 7. Open camera housing using the 3 cover screws without removing the protective wrap from the lens. Page 8 forticam-CD51.
8. 9. Place the camera on the mounting plate so the sockets fit into the matching recesses on the camera bottom. Fasten the camera with the two supplied machine bolts (M4 x 10mm) to the sockets. 10. Open the MicroSD card socket lid by sliding it backwards. This and the following two steps are only required if onboard storage is preferred. Page 9 forticam-CD51.
11. Insert a MicroSD card into the socket, close the lid, and then slide the lid until you hear a click. 12. Press the reset button on the camera. Page 10 forticam-CD51.
13. Adjust the camera’s pan, tilt, and rotation angle. 14. Replace the dry pack found inside the camera with the fresh one from the protective pouch in the box. Ensure no moisture gets trapped inside the camera. 15. Install the dome cover and remove the protective wrap. Page 11 forticam-CD51.
Mounting Plate Details The following table is an explanation of the various mounting holes on the mounting plate and their function.
Page 13 forticam-CD51.
Status LED Explanation The following table is an explanation of the various statuses of the camera. Note: Status LEDs can be disabled through software Note: Bluetooth pairing mode is active after a factory reset or it can be entered via the reset button or software command.
Camera Connection Caution: This device complies with IEEE 802.3af PoE specification. Do not use any PoE injectors that are not IEEE 802.3af compliant as they may damage your device. Attention Cet appareil est conforme à la spécification PoE IEEE 802.3af. Attention: N’utilisez pas d’injecteurs PoE non conformes à la norme IEEE 802.3af car ils pourraient endommager votre appareil.
2. Go to the FortiRecorder web UI to configure the discovered camera. For details, see the FortiRecorder Administration Guide on http://docs.fortinet.com. To use Bluetooth functionality 1. Power up or reset the camera and watch the Status LED for Bluetooth Pairing mode. 2. Use FortiRecorder Mobile on your mobile device to discover and pair with the camera. 3. Configure the camera locally. The camera should be able to connect to the recorder at this point.
Technical Specifications Camera Format Fixed dome, day/night, indoor/outdoor, vandal Sensor Type 5 mega-pixel, 1/2.8” low light CMOS Iris F2.0/fixed Focal Length f=2.8 mm View Angle H:95°, V:72°, D118° Minimum Illumination 0.05 Lux (color) @ F2 and 0.01 Lux (B/W) @ F2 WDR HDR (>80dB) Network Interface RJ-45 Ethernet 10/100 Mbps IRLED/IRC 20+m/yes, dimmable 3DNR Yes Streaming Protocol RTSP SD Card 512 GB SD card (Reserved) Video Compression H.264/H.
Mounting Wall, ceiling, tile, 3-axis, 3/4” conduit, junction box Wifi/Bluetooth Number of Antennas 1 internal Peak Antenna Gain 3.4dBi for 2.4GHz, 4.1dBi for 5GHz Frequency of Radio 1 2.4GHz b/g/n or 5GHz a/n/ac Bluetooth Features BLE V5.0 3.4dBi @ 2.4GHz Dimensions Height x Width x Length 3.8 x 4.7 x 4.7’’ (97 x 120 x 120 cm) Weight 1.09lb (498g) Environment Power Required PoE (802.3af ) class 3 Power Consumption (AVG) < 12.
Register for Support Register your Fortinet product to receive: • Technical support • New product features • Protection from new threats Vous devez enregistrer le produit pour recevoir: • Support technique • Nouvelles fonctionnalitées du produit • Protection contre de nouvelles menaces La reistrazione ti permette di usufruire di: • Supporto tecnico • Nuove funzionalita • Proteezione dalle ultime minaccce Debe registrar el producto para recibir: • Apoyo técnico • Nuevas funcionalidades del producto • Protecc
Cautions and Warnings Environmental Specifications Ambient operating temperature: -40°C to 50°C Refer to specific Product Model Data Sheet for Environmental Specifications (Operating Temperature, Storage Temperature, Humidity, and Altitude) Référez à la Fiche Technique de ce produit pour les caractéristiques environnementales (Température de fonctionnement, température de stockage, humidité et l’altitude). Safety Caution: This equipment is to be used in a Network Environment 0 per IECTR 62101.
Regulatory Notices Federal Communication Commission (FCC) – USA This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received; including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: 1. L’appareil ne doit pas produire de brouillage; 2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
European Conformity (CE) - EU This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. The product transmits within the frequency ranges and less than or equal to the power listed below: 2402-2480MHz less than 20dBm 2412-2472MHz less than 20dBm 5180-5240MHz less than 23dBm This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Español Este producto cumple con la Directiva 2014/53/UE. Ελληνική Το προϊόν αυτό συμμορφώνεται με την Οδηγία 2014/53/ΕΕ. Français Ce produit est conforme à la Directive 2014/53/UE. Hrvatski Ovaj proizvod je u skladu s Direktivom 2014/53/EU. Italiano Questo prodotto è conforme alla Direttiva 2014/53/EU. Latviski Šis produkts atbilst Direktīvai 2014/53/ES. Lietuvių Šis gaminys atitinka direktyvą 2014/53/ES. Malti Dan il-prodott huwa konformi mad-Direttiva 2014/53/UE.
Ten produkt jest zgodny z dyrektywą 2014/53/UE. Português Este produto está em conformidade com a Diretiva 2014/53/UE. Rumunski Acest produs este în conformitate cu Directiva 2014/53/UE. Slovensky Tento produkt je v súlade so smernicou 2014/53/EÚ. Slovensko Ta izdelek je v skladu z Direktivo 2014/53/EU. Suomi Tämä tuote on direktiivin 2014/53/EU mukainen. Svenska Denna produkt överensstämmer med direktiv 2014/53/EU.
Product License Agreement/EULA and Warranty Terms Product License Agreement The parties to this agreement are you (the end-customer) and Fortinet, Inc. (“Fortinet”). CAREFULLY READ THE FOLLOWING LEGAL AGREEMENT (THE OR THIS “AGREEMENT” OR “EULA”).
2. Limitation on Use.
and/or end user, (iii) comply with all applicable United States export control laws and regulations and all other applicable laws, and (iv) refund any fees paid to you by a customer and/or end user who purchased Product(s) from you but does not agree to the restrictions and obligations contained in this Agreement and therefore wishes to return the Product(s) as provided for in this Agreement.
Software with software that substantially conforms to Fortinet’s functional specifications. This obligation is exclusive of transport fees, labor, de-installation, installation, reconfiguration, or return shipment and handling fees and costs, and Fortinet shall have no obligation related thereto.
8. Governing Law. Any disputes arising out of this Agreement or Fortinet’s limited warranty shall be governed by the laws of the state of California, without regard to the conflict of laws principles.
that you and your employees have not accepted, and will not accept, anything of value, including money, meals, entertainment, paid-for travel, beta, testing, evaluation, donation or free Products and/or related services, or anything else of value, in exchange for Fortinet maintaining current business or for new business opportunities.
15. Open Source Software. Fortinet’s products may include software modules that are licensed (or sublicensed) to the user under the GNU General Public License, Version 2, of June 1991 (“GPL”) or GNU Lesser General Public License, Version 2.
at your option offer warranty protection in exchange for a fee. 2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change.
attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance. 5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or its derivative works.
the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally. NO WARRANTY 11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW.
1. You may copy and distribute verbatim copies of the Library’s complete source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and distribute a copy of this License along with the Library.
compiled or linked with it, is called a “work that uses the Library”. Such a work, in isolation, is not a derivative work of the Library, and therefore falls outside the scope of this License. However, linking a “work that uses the Library” with the Library creates an executable that is a derivative of the Library (because it contains portions of the Library), rather than a “work that uses the library”. The executable is therefore covered by this License.
7.
13. The Free Software Foundation may publish revised and/or new versions of the Lesser General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. Each version is given a distinguishing version number.
forticam-CD51.
