SECURITY SYSTEM ONLY REMOTE CAR STARTER ONLY SECURITY SYSTEM AND REMOTE CAR STARTER AUTOMATIC / MANUAL TRANSMISSION - 2-WAY REMOTES RM912 User Guide Model : REM912 FCC ID: 2ACKU-RM912 IC: 12084A-RM912 Manufacture : FORTIN Model : ANT900 FCC ID: 2ACKU-ANT900 IC: 12084A-ANT900 Manufacture : FORTIN DESIGNED & ENGINEERED IN CANADA DOC#: 68421 - REV:H 20170629 © 2017 ALL RIGHTS RESERVED
TABLE DES MATIÈRES TABLE TABLE OF OF CONTENTS CONTENTS ......................................................................................................................... 2 INTRODUCTION ................................................................................................................................. 2 CAUTION - WARNING ......................................................................................................................... 3 NOTE .........................................
CAUTION - WARNING IT IS THE RESPONSIBILITY OF THE REMOTE CAR STARTER OPERATOR TO: • • • • ensure that the vehicle is parked in a safe and responsible manner. ensure that the vehicle is not remotely started indoors (garage, underground parking). ensure that the vehicle is not remotely started with a passenger inside. ensure that the gearshift lever is in the NEUTRAL position and the parking brake is engaged on manual transmission in order to avoid accidents upon remote starting.
• Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. This device complies with the Industry Canada Radio Standards Specification RSS 210.
REMOTE-STARTING REMOTE-STARTING THE VEHICLE This Remote-Starter supports both manual and automatic transmission vehicles. For manual transmission vehicles see the Ready Mode section. REMOTE-STARTING STEP1 To remote-start the vehicle press the button for approximately 3 second. The remote Green Led turn ON for 1 second and a ascending melodie will sound to confirm. STEP 2 The parking lights will turn on to indicate a response to the RemoteStart signal.
METHOD 1 PROGRAMMED BY DEFAULT THIS METHOD WILL ACTIVATE THE REMOTE CAR STARTER SEQUENCE ONLY WHEN THE END USER IS USING THE REMOTE CAR STARTER REMOTE: The vehicle must be running. STEP 1 Make sure that all doors are closed and the transmission is in the NEUTRAL position. and STEP 2 Engage the parking brake. STEP 3 Release the brake pedal. STEP 4 STEP 5 Press the button for 3 seconds. The remote Green Led turn ON for 1 second and a ascending melodie will sound to confirm.
DRIVING OFF When the vehicle is running with the Remote-Starter, enter the vehicle and proceed with the following steps: OFF STEP 1 IGN START STEP 2 Insert the key and turn it to the ignition (ON/Run) position. WARNING: Do not turn the key to the START position when the engine is running. This may damage the ignition system on some vehicles. Step on the brake pedal to disable the Remote-Starter, and put the vehicle in gear.
STEP 5 Press the button for 3 seconds. The remote Green Led turn ON for 1 second and a ascending melodie will sound to confirm and the parking lights will flash once and then remain on. STEP 6 OFF Remove the key from the ignition barrel. The vehicle will continue to run with the the Remote-Starter. STEP 7 Exit the vehicle and close all of the doors. The vehicle will continue to run after all the doors are closed. STEP 7 Remote-stop the vehicle. Press the button for 3 seconds.
VALET MODE (VIA SWITCH) Valet Mode disables both the Remote-Starter and Alarm system. Whenever the vehicle is being serviced or repaired, or the vehicle is parked indoors it is mandatory that Valet Mode be enabled to prevent an accidental Remote-Start. Note: The alarm system is not active (including Starter Kill) when the system is in Valet Mode. However you are still able to lock and unlock the doors, and release the rear hatch/trunk.
REMOTE DOOR LOCKS If the Remote-Starter is installed with door locks, you will be able to lock and unlock the vehicle without using the key or OEM key fob. To UNLOCK the doors and DISARM the Alarm: Press the button twice for 0.5 second. The remote Green Led flash and beep once to confirm. The parking lights will flash twice and the LED will turn OFF to confirm the signal. The Starter-Kill will also deactivate allowing the vehicle to be started with the key.
will immediately resound if a zone is (re)triggered. • Execute the UNLOCK function TWICE to stop the alarm sound, deactivate the Alarm, and unlock the doors. • When the vehicle is unlocked the horn/siren will sound with several short chirps to indicate the zone that has previously triggered the Alarm. (See Remote-Start/Alarm Diagnostics page 12) NOTE 1: If the vehicle is running with the Remote-Starter and the Alarm is triggered the Remote-Starter will shut down immediately.
a dialectic grease to prevent corrosion. • Trailer wiring. Corroded or improperly wired trailer wiring may cause the park light signal to bleed into the brake signal. This will cause the Remote-Starter to shut down as soon as the park lights are turned on. • Problems with the Bypass Kit (if installed). If you are able to put the Remote-Starter into Ready Mode, Idle Mode, or Turbo Mode, but you are unable to Remote-Start the vehicle then the Bypass Kit may be failing.
USER GUIDE Page 13 / 12