SECURITY SYSTEM ONLY REMOTE CAR STARTER ONLY SECURITY SYSTEM AND REMOTE CAR STARTER AUTOMATIC / MANUAL TRANSMISSION - 1-WAY REMOTES FTX84-1W User Guide Model : FTX84 FCC ID : 2ACKU-R1W02FM IC : 12084A-R1W02FM Manufacture : FORTIN Model : ANT-FMH-2W FCC ID : 2ACKU-A2W01FM IC : 12084A-A2W01FM Manufacture : FORTIN DESIGNED & ENGINEERED IN CANADA DOC#: 68321 - REV:G 20170908 © 2017 ALL RIGHTS RESERVED
TABLE DES MATIÈRES TABLE TABLE OF OF CONTENTS CONTENTS ......................................................................................................................... 2 INTRODUCTION ................................................................................................................................. 2 CAUTION - WARNING ......................................................................................................................... 3 NOTE ........................................
CAUTION - WARNING IT IS THE RESPONSIBILITY OF THE REMOTE CAR STARTER OPERATOR TO: • • • • ensure that the vehicle is parked in a safe and responsible manner. ensure that the vehicle is not remotely started indoors (garage, underground parking). ensure that the vehicle is not remotely started with a passenger inside. ensure that the gearshift lever is in the NEUTRAL position and the parking brake is engaged on manual transmission in order to avoid accidents upon remote starting.
• Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. This device complies with the Industry Canada Radio Standards Specification RSS 210.
USING THE REMOTE CONTROL The remote starter is equipped with two 1-way 4-button multi-channel remote control. TIME PRESSED DESCRIPTION LOCK 0,5 SEC. Locks all doors, arm the anti-theft system and activates the Alarm (if installed). Press LOCK for 3 seconds to activate the Panic Mode UNLOCK 0,5 SEC. Unlocks all doors, disarms the anti-theft system and deactivates the Alarm (if installed). START 3 SEC. Remote-start the vehicle. Press START again to reset the runtime.
REMOTE-STARTING REMOTE-STARTING THE VEHICLE This Remote-Starter supports both manual and automatic transmission vehicles. For manual transmission vehicles see the Ready Mode section. REMOTE-STARTING STEP 1 To remote-start the vehicle press the START button for approximately 3 second. STEP 2 The parking lights will turn on to indicate a response to the Remote-Start signal. STEP 3 Approximately 5 seconds later the engine will crank.
METHOD 1 PROGRAMMED BY DEFAULT THIS METHOD WILL ACTIVATE THE REMOTE CAR STARTER SEQUENCE ONLY WHEN THE END USER IS USING THE REMOTE CAR STARTER REMOTE: The vehicle must be running. STEP 1 Make sure that all doors are closed and the transmission is in the NEUTRAL position. and STEP 2 Engage the parking brake. STEP 3 Release the brake pedal. STEP 4 Press the START button for 3 seconds. The parking lights will flash once and then remain on. STEP 5 OFF STEP 6 Remove the key from the ignition barrel.
DRIVING OFF STEP 1 OFF When the vehicle is running with the Remote-Starter, enter the vehicle and proceed with the following steps: IGN START Insert the key and turn it to the ignition (ON/Run) position. Warning: Do not turn the key to the START position when the engine is running. This may damage the ignition system on some vehicles. STEP 2 Step on the brake pedal to disable the Remote-Starter, and put the vehicle in gear.
STEP 4 Release the brake pedal. STEP 5 Press the remote START button. The parking lights will flash once and then remain on. STEP 6 OFF STEP 7 Remove the key from the ignition barrel. The vehicle will continue to run with the the Remote-Starter. Exit the vehicle and close all of the doors. The vehicle will continue to run after all the doors are closed. STEP 8 Remote-stop the vehicle.
after the doors are locked. The LED will turn off only after the Remote-Starter/Alarm exit Valet Mode. VALET CODING DISABLED (DEFAULT): To activate and deactivate Valet Mode using the valet switch proceed with the following steps: OFF STEP 1 IGN START Insert the key and turn it to the ignition (ON/RUN) position. The vehicle does not need to be started. STEP 2 FMH 2-W Within 10 seconds press and release the button on the antenna 3 times.
To enable Cold Start Timer Mode proceed with the following steps. + ress and release the FUNCTION button, within 12 seconds simultaneously press and and hold the LOCK and START buttons for 1 second. To disable Cold Start Timer Mode do any of the following: • Press and release the FUNCTION button, within 12 seconds to simultaneously press the LOCK and the START buttons for 1 second until the parking light flash twice. • Put the Remote-Starter/ alarm into Valet Mode. Remote-Start the vehicle.
WARNING: This Remote-Starter must be installed by a trained professional. Improper modifications to any of the following settings could adversely affect the reliability of the Remote-Starter and/or the vehicle’s operation.
RUNTIME On gas engines the Remote-Starter can run the vehicle for either 3, 7 or 15 (default) minutes. On diesel engines the Remote-Starter can run the vehicle for either 6, 15 or 30 (default) minutes. RUNTIME RESET Once the vehicle is running with the Remote-Starter the runtime can be reset (before it expires) at any time by pressing the START button while the vehicle is Remote-Started. The horn/siren will sound once to confirm (If installed).
VEHICLE LOCATOR/PANIC MODE To locate your vehicle in a busy parking lot press the LOCK button for 3 seconds to sound the horn/siren (If installed) and flash the parking lights. Press unlock to cancel this Mode. Note: If an Alarm pre-triggered zone is in memory, this Mode will NOT clear this zone from memory. SENSOR DEACTIVATION In cases where a sensor is too sensitive and causes false alarms, it is possible to disable some of the zones.
installation centre may refuse all fees incurred by the latter service centre (if any).