SECURITY SYSTEM ONLY REMOTE CAR STARTER ONLY SECURITY SYSTEM AND REMOTE CAR STARTER AUTOMATIC / MANUAL TRANSMISSION - 1-WAY REMOTES FTX900 User Guide Model : FTX900 FCC ID : 2ACKU-R1W01FSS IC : 12084A-R1W01FSS Manufacture : FORTIN DESIGNED & ENGINEERED IN CANADA DOC#: 68381 - REV:G 20170719 © 2017 ALL RIGHTS RESERVED
TABLE DES MATIÈRES TABLE TABLE OF OF CONTENTS CONTENTS ......................................................................................................................... 2 INTRODUCTION ................................................................................................................................. 2 CAUTION - WARNING ......................................................................................................................... 3 NOTE ........................................
CAUTION - WARNING IT IS THE RESPONSIBILITY OF THE REMOTE CAR STARTER OPERATOR TO: • • • • ensure that the vehicle is parked in a safe and responsible manner. ensure that the vehicle is not remotely started indoors (garage, underground parking). ensure that the vehicle is not remotely started with a passenger inside. ensure that the gearshift lever is in the NEUTRAL position and the parking brake is engaged on manual transmission in order to avoid accidents upon remote starting.
• Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. This device complies with the Industry Canada Radio Standards Specification RSS 210.
+ Press and release FUNCTION and then press simultaneously LOCK and FUNCTION LOCKED THE REMOTE Until the BLUE LED turn on. See : REMOTE LOCKING AND UNLOCKING, page 11 The BLUE LED will come on Whenever a button is pressed when the remote is LOCKED. UNLOCKED THE REMOTE Until the RED LED turn on. See : REMOTE LOCKING AND UNLOCKING, page 11 The remote LED flash RED when a button is pressed. The remote LED flash RED when the remote is transmitting the informations.
ACCESSORY PRESET Heater & Heated Seat(s): When leaving the vehicle it is recommended that the driver pre-set the climate controls in preparation for a later Remote-Start. When the vehicle RemoteStarts, the current (or last) setting for the climate controls, windshield wipers (and other accessories) will be used. When setting the blower motor (fan speed) and heated seats (if equipped) should not be left on HIGH. It is recommended to leave these settings on either a LOW or MEDIUM setting.
STEP 6 Exit the vehicle and close all of the doors. The Remote-Starter will stop running once all the doors are closed. METHOD 2 This method must be programmed by the installer during installation. THIS METHOD WILL ACTIVATE THE REMOTE STARTER SEQUENCE EVERYTIME THE END USER IS LEAVING THE VEHICLE. AUTOMATIC ACTIVATION: The vehicle must be running. STEP 1 Make sure the transmission is in the NEUTRAL position. STEP 2 Engage the parking brake. STEP 3 Release the brake pedal.
to reset this timer. To activate Idle Mode (automatic transmission) proceed with the following steps: STEP 1 With the key in the barrel at the ignition (ON/RUN) position and the engine running, press the START button until the parking lights turn on. STEP 2 OFF Turn the key to the OFF position and remove the key from the ignition barrel. The vehicle will continue to run with the Remote-Starter.
TURBO MODE (AUTOMATIC TRANSMISSION) Turbo Mode (if installed) is similar to Idle Mode but is used to cool down the turbo-charger once the driver leaves the vehicle. The Remote-Starter will continue run the vehicle for 2 minutes allowing the turbo-charger to cool down. To activate Turbo Mode (automatic transmission) proceed with the following steps: STEP 1 With the engine already running, press the remote START button until the parking lights come on. STEP 2 OFF Remove the key from the ignition barrel.
enabling/disabling Valet Mode uses the remote transmitter instead of the valet switch indicated in the preceding section. To enter Valet Mode using the remote transmitter proceed with the following steps: STEP 1 + Press and release the FUNCTION button, within 12 seconds simultaneously press and hold the LOCK and UNLOCK buttons for 1 second. STEP 2 FMH 2-W The LED will turn ON solid and remain ON.
Aux 2 : Passenger side sliding door (if installed). Press and relase the FUNCTION button (the remote LED flashes slowly white) within 12 seconds press the UNLOCK button. Note: The function of the auxiliary outputs may vary depending on the vehicle and the installation. In most cases these outputs are not used, and in some cases they may be used to control other features such as the power windows, sunroof, or heated seats.
To LOCK the doors and ARM the Alarm: The parking light will flash once and the LED will turn ON to confirm the signal. The Starter-Kill will activate preventing the Press the LOCK but- vehicle from being started with the key. If LOCK is pressed again ton for 0.5 second. (consecutively) the horn will honk once (if installed) to confirm. Note: The system can be configured during installation so the horn confirms LOCK on the first attempt.
ALARM ACTIVITY The following characteristics enhance your vehicle’s security : If the Alarm system is active and the horn/siren is sounding : • Press the UNLOCK button ONCE to stop the alarm sound. The Alarm will remain active and will immediately resound if a zone is (re)triggered. • Press the UNLOCK button TWICE to stop the alarm sound, deactivate the Alarm, and unlock the doors.
• Hold the transmitter at shoulder height or hold it against your chin so your body acts as a larger antenna. • The operating range will be somewhat poorer on vehicles equipped with a factory alarm or keyless entry system. FAILED REMOTE-START There are several different installation factors and devices that must work together in order for your vehicle to Remote-Start properly. In some cases a failed Remote Start is not the fault of the RemoteStarter itself.