Table of contents Introduction Congratulations Safety and environment protection Symbol glossary Instrument cluster 4 4 5 10 12 Warning and control lights Gauges 12 16 Entertainment systems 20 AM/FM AM/FM AM/FM AM/FM stereo stereo cassette stereo cassette with CD stereo with CD Climate controls Heater only Manual heating and air conditioning Lights Headlamps Bulb replacement Driver controls Windshield wiper/washer control Steering wheel adjustment Power windows Mirrors 20 20 31 41 78 78 79 85
Table of contents Seating and safety restraints Seating Safety restraints Air bags Child restraints Driving 113 121 132 137 148 Starting Brakes Transmission operation Vehicle loading Trailer towing Recreational towing 148 152 156 160 163 172 Roadside emergencies 173 Hazard flasher switch Fuses and relays Changing tires Jump starting Wrecker towing 174 177 184 191 196 Customer assistance 197 The dispute settlement board Utilizing the mediation/arbitration Getting assistance outside the U.S.
Table of contents Maintenance and specifications Hood Engine compartment Engine oil Battery Fuel information Air filter(s) Part numbers Refill capacities Lubricant specifications Engine data Vehicle dimensions 214 215 216 217 220 233 247 253 254 258 260 261 Accessories 264 Index 267 All rights reserved.
Introduction The following warning may be required by California law: CALIFORNIA Proposition 65 Warning WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Introduction Fuel pump shut-off switch In the event of an accident the safety switch will automatically cut off the fuel supply to the engine. The switch can also be activated through sudden vibration (e.g. collision when parking). To reset the switch, refer to the Fuel pump shut-off switch in the Roadside emergencies chapter.
Introduction SPECIAL NOTICES Emission warranty The New Vehicle Limited Warranty includes Bumper-to-Bumper Coverage, Safety Restraint Coverage, Corrosion Coverage, and 7.3L Power Stroke Diesel Engine Coverage. In addition, your vehicle is eligible for Emissions Defect and Emissions Performance Warranties. For a detailed description of what is covered and what is not covered, refer to the Warranty Guide that is provided to you along with your Owner’s Guide.
Introduction Notice to owners of pickup trucks and utility type vehicles Utility vehicles have a significantly higher rollover rate than other types of vehicles. Before you drive your vehicle, please read this Owner’s Guide carefully. Your vehicle is not a passenger car. As with other vehicles of this type, failure to operate this vehicle correctly may result in loss of control or an accident.
Introduction Notice to owners of natural gas fueled vehicles Before you drive your vehicle, be sure to read the “Natural Gas Vehicle Owner’s Guide Supplement.” This book contains important operation and maintenance information.
Introduction Middle East/North Africa vehicle specific information For your particular global region, your vehicle may be equipped with features and options that are different from the ones that are described in this Owner Guide; therefore, a supplement has been supplied that complements this book. By referring to the pages in the provided supplement, you can properly identify those features, recommendations and specifications that are unique to your vehicle.
Introduction These are some of the symbols you may see on your vehicle.
Introduction Vehicle Symbol Glossary Child Safety Door Lock/Unlock Interior Luggage Compartment Release Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant Temperature Do Not Open When Hot Battery Avoid Smoking, Flames, or Sparks Battery Acid Explosive Gas Fan Warning Power Steering Fluid Maintain Correct Fluid Level Emission System Engine Air Filter Passenger Compartment Air Filter Jack Check fuel cap Low tire warning MAX MIN 11
Instrument cluster WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’s functions. Many lights will illuminate when you start your vehicle to make sure the bulb works. If any light remains on after starting the vehicle, have the respective system inspected immediately.
Instrument cluster followed by mixed city/highway driving.) No additional vehicle service is required. If the light remains on, have your vehicle serviced at the first available opportunity. Light is blinking: Engine misfire is occurring which could damage your catalytic converter. You should drive in a moderate fashion (avoid heavy acceleration and deceleration) and have your vehicle serviced at the first available opportunity.
Instrument cluster Air bag readiness Illuminates to confirm that the air bags (front or side) are operational. If the light fails to illuminate, continues to flash or remains on, have the system serviced immediately. Charging system Illuminates when the battery is not charging properly. Low fuel Illuminates when the fuel level in the fuel tank is at, or near, empty (refer to Fuel gauge in this chapter for more information).
Instrument cluster Transmission control indicator light (TCIL) Illuminates when the overdrive function of the transmission has OVERDRIVE been turned OFF using the Transmission Control Switch (TCS). Refer to the Driving chapter for transmission function and operation. If the light does not come on or if the light flashes steadily, have your vehicle serviced as soon as possible, damage to the transmission could occur. Turn signal Illuminates when the turn signals or the hazard lights are turned on.
Instrument cluster Supplemental restraint system (SRS) warning chime Sounds when a malfunction in the supplemental restraint system (front or side airbags) has been detected. Have the supplemental restraint system inspected immediately. Headlamps on warning chime (if equipped) Sounds when the headlamps or parking lamps are on, the key is removed from the ignition and the driver’s door is opened. Key-in-ignition warning chime/buzzer Sounds when the key is left in the ignition and the driver’s door is opened.
Instrument cluster Engine coolant temperature gauge Indicates the temperature of the engine coolant. At normal operating temperature, the needle remains within the normal area (the area between the “H” and “C”). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the engine immediately and let the engine cool. Refer to Engine coolant in the Maintenance and specifications chapter.
Instrument cluster Battery voltage gauge Indicates battery voltage. If the pointer moves and stays outside the normal operating range (as indicated by the arrows), have the vehicle’s electrical system checked as soon as possible. 18 8 Fuel gauge Displays approximately how much fuel is in the fuel tank. The fuel F gauge may vary slightly when the vehicle is in motion or on a grade.
Instrument cluster Odometer Registers the total kilometers (miles) of the vehicle. Trip odometer Registers the kilometers (miles) of individual journeys. To reset, depress the control.
Entertainment systems USING YOUR AUDIO SYSTEM AM/FM Stereo (with 2 speakers) VOL PUSH ON TONE TONE VOL ST SEEK DX FM 12 TUNE CLK 1 2 3 4 AM/FM AM/FM Stereo (with 4 speakers and fade capability) VOL PUSH ON TONE TONE VOL ST SEEK DX FM 12 TUNE CLK AM / FM STEREO 1 20 2 3 4 AM/FM
Entertainment systems Volume/power control Press the control to turn the audio system on or off. VOL PUSH ON Turn the control to raise or lower volume. VOL PUSH ON If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. Bass adjust The bass adjust control allows you to increase or decrease the audio system’s bass output.
Entertainment systems Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Press the TONE control three times, then use the volume knob to adjust the desired level. Speaker fade adjust (if equipped) Speaker sound can be adjusted between the front and rear speakers. Press the TONE control four times, then use the volume knob to adjust the desired level. VOL PUSH ON TONE CLK VOL PUSH ON TONE CLK Seek function The seek function control works in radio mode.
Entertainment systems Radio station memory preset The radio is equipped with four station memory preset controls. These controls can be used to select up to four preset AM stations and eight FM stations (four in FM1 and four in FM2). Setting memory preset stations 1. Select the frequency band with the AM/FM select control. 2. Select a station. Refer to Tune adjust or Seek function for more information on selecting a station. 3.
Entertainment systems To set the minute, press and hold the CLK control until CLOCK SET appears in the display and press the TUNE control: TONE CLK to decrease minutes and • SEEK SEEK to increase minutes. • TUNE TUNE The CLK control will allow you to switch between media display mode (radio station, stereo information, etc.) and clock display mode (time). When in clock mode, the media information will display for ten seconds, when the radio is turned on, and then revert to clock information.
Entertainment systems AM/FM STEREO CASSETTE VOL - PUSH ON AM CLK ST FM1 BASS TREB BAL FADE FM SEEK SCAN SIDE REW EJ TUNE 1 2 3 Volume/power control Press the control to turn the audio system on or off. Turn the control to raise or lower volume. 4 5 TAPE AMS 1-2 FF 6 VOL - PUSH ON VOL - PUSH ON If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on.
Entertainment systems Bass adjust The bass adjust control allows you to increase or decrease the audio system’s bass output. BASS Treble adjust The treble adjust control allows you to increase or decrease the audio system’s treble output. TREB Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers.
Entertainment systems Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. FADE Seek function The seek function control works in radio mode. Seek function in radio mode to find the next • Press listenable station down the frequency band. to find the next • Press listenable station up the frequency band. Scan function The scan function works in radio mode.
Entertainment systems AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the AM control to select from AM selections, and press the FM control to select from FM1 or FM2 memory preset stations. AM/FM select in tape mode Press this control to stop tape play and begin radio play. Radio station memory preset The radio is equipped with six station memory preset controls.
Entertainment systems To set the minute, press and hold the CLK control and press the TUNE control: CLK TAPE AMS • • to decrease minutes and to increase minutes. SEEK TUNE DISCS The CLK control will allow you to switch between media display mode (radio station, stereo information, etc.) and clock display mode (time). When in clock mode, the media information will display for 10 seconds, when the radio is turned on, and then revert to clock information.
Entertainment systems Tape select • To enter tape mode while in radio mode, press the TAPE AMS control. CLK TAPE AMS Automatic Music Search The Automatic Music Search feature allows you to quickly locate the beginning of the tape selection CLK being played or to skip to the next selection. TAPE To activate the feature, momentarily AMS depress the TAPE AMS button. Then, press either REW (for the beginning of the current selection) or FF (to advance to the next selection).
Entertainment systems Tape direction select Press SIDE and 1–2 at the same time to play the alternate side of a tape. SIDE REW Eject function Press the control to stop and eject a tape. 1-2 FF EJ Dolby姞 noise reduction Dolby威 noise reduction operates only in tape mode. Dolby威 noise 4 reduction reduces the amount of hiss and static during tape playback. control to activate (and deactivate) Dolby威 noise Press the reduction.
Entertainment systems Volume/power control Press the control to turn the audio system on or off. Audio power can also be turned on by pressing the AM/FM select control or the tape/CD select control. Audio power is turned off by using the volume/power control. Turn control to raise or lower volume. VOL - PUSH ON VOL - PUSH ON If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on.
Entertainment systems Treble adjust The treble adjust control allows you to increase or decrease the audio system’s treble output. Press the TREB control then press: to decrease the treble output • and to increase the treble output. • BASS SEL Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Press the BAL control then press: to shift sound to the left and • to shift sound to the right.
Entertainment systems • to shift the sound to the front and to shift the sound to the rear. • SEL Seek function The seek function control works in radio, tape or CD mode. Seek function in radio mode to find the next • Press listenable station down the frequency band. to find the next • Press listenable station up the frequency band. Seek function in tape mode to listen to the previous selection on the tape. • Press to listen to the next selection on the tape.
Entertainment systems Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band. Press the control again to stop the scan mode. Scan function in tape mode Press the SCAN control to hear a short sampling of all selections on the tape. (The tape scans in a forward direction. At the end of the tape’s first side, direction automatically reverses to the opposite side of the tape.) To stop on a particular selection, press the control again.
Entertainment systems REW FF SIDE 1-2 1 2 3 4 COMP SHUFFLE 5 6 3. Press and hold a memory preset control until the sound returns, indicating the station is held in memory on the control you selected. Autoset memory preset Autoset allows you to set strong radio stations without losing your original manually set preset stations. This feature is helpful on trips when you travel between cities with different radio stations. Starting autoset memory preset 1.
Entertainment systems Setting the clock To set the hour, press and hold the CLK control and press SEEK: AUTO CLK • • to decrease hours and to increase hours. To set the minute, press and hold the CLK control and press TUNE: AUTO CLK to decrease minutes and • to increase minutes. • If your vehicle has a separate clock, (other than the digital radio display), the CLK control will not function in the above manner.
Entertainment systems The CLK control will allow you to switch between media display mode AUTO (radio station, stereo information, etc.) and clock display mode (time). When in clock mode, the media information will display for 10 CLK seconds, when the radio is turned on, and then revert to clock information. Any time that the media is changed, (new radio station, etc.), the media information will again display for 10 seconds before reverting back to the clock.
Entertainment systems Do not insert any promotional (odd shaped or sized) discs, or discs with removable labels into the CD player as jamming may occur. Rewind The rewind control works in tape REW and CD modes. 1 • In tape mode, radio play will continue until rewind is stopped (with the TAPE control) or the beginning of the tape is reached. • In CD mode, pressing the REW control rewinds the CD within the current track. Fast forward The fast forward control works in FF tape and CD modes.
Entertainment systems Dolby姞 noise reduction Dolby威 noise reduction operates in tape mode. Dolby威 noise reduction 4 reduces the amount of hiss and static during tape playback. control to activate (and deactivate) the Dolby威 noise Press the reduction. Dolby威 noise reduction is manufactured under license from Dolby威 Laboratories Licensing Corporation. “Dolby威” and the double-D are registered trademarks of Dolby威 Laboratories Licensing symbol Corporation.
Entertainment systems PREMIUM AM/FM STEREO IN DASH SIX CD RADIO SHUF DISC TUNE SCAN SEEK REW FF COMP MUTE EJ LOAD BASS BAL SEL TREB FADE PUSH ON AM FM CD 1 2 3 4 5 6 MENU Volume/power control Press the control to turn the audio system on or off. PUSH ON Turn the control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on.
Entertainment systems Bass adjust The bass adjust control allows you to increase or decrease the audio system’s bass output. Press the BASS control. Use the SEL control to increase or decrease the amount of bass. Treble adjust The treble adjust control allows you to increase or decrease the audio system’s treble output. Press the TREB control. Use the SEL control to increase or decrease the amount of treble.
Entertainment systems Seek function in radio mode to find the next • Press listenable station down the frequency band. SEEK DOWN will display. to find the next listenable station up the frequency band. • Press SEEK UP will display. Seek function in CD mode to seek to the previous • Press track of the current disc. If the beginning of the disc is reached, the CD player seeks to the beginning of the last track on the current disc and begins playing. to seek forward to the next track of the current disc.
Entertainment systems AM/FM select The AM/FM select control works in radio and CD modes. AM FM CD AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations. AM/FM select in CD mode Press this control to stop CD play and begin radio play. Radio station memory preset The radio is equipped with six station memory preset controls.
Entertainment systems Autostore Autostore allows you to set the strongest local radio stations without losing your original manually set preset stations. This feature is helpful on trips when you travel between cities with different radio stations. Starting autostore 1. Press and momentarily hold the AM/FM control. 2. AUTOSET will flash in the display AM CD as the frequency band is scrolled FM through. 3.
Entertainment systems Tune adjust in radio mode to move to the next • Press frequency down the band (whether or not a listenable station is located there). Hold the control to move through the frequencies quickly. to move to the next frequency up the band (whether or not • Press a listenable station is located there). Hold for quick movement. Tune adjust for CD mode to select the previous • Press disc. (Play will begin on the first track of the disc unless shuffle mode is engaged.
Entertainment systems Do not insert any promotional (odd shaped or sized) discs, or discs with removable labels into the CD player as jamming may occur. Display description Six circles are always lit in the digital display. These signify the six CD slots in the audio system. When a disc is loaded into a particular slot (1–6), the number inside that specific circle lights. If the circle is empty, there is no CD in that particular slot. Rewind The rewind control works in CD modes.
Entertainment systems open. Compact discs should only be loaded by pressing the LOAD control. Press the LOAD control. (You can choose which slot will be loaded by pressing the desired preset number. If you do not choose a slot, the system will choose the next available one.) Wait until the CD door opens. Load the CD into the player. LOADING CD# is displayed. When the CD has been loaded, the door will close and the CD will begin to play.
Entertainment systems Auto eject Press and momentarily hold the EJ control to engage auto eject. All CDs which are present in the player will be ejected one at a time. If a CD is ejected and not removed from the door of the CD player, the player will automatically reload the CD. This feature may be used when the ignition is ON or OFF. Shuffle feature Press the SHUF control until the desired shuffle mode is displayed. The audio system will then engage the desired shuffle mode.
Entertainment systems Menu mode The MENU control allows you to access many different features within your audio system. There are three sets of menus available depending upon which mode or feature is activated. While in FM mode, two menus are available. If RDS is turned OFF, you can access the following: • SELECT HOURS — Refer to Setting the clock. • SELECT MINUTES — Refer to Setting the clock. • RDS OFF — Refer to Radio data system feature.
Entertainment systems Radio data system (RDS) feature This feature allows your audio system to receive text information MENU + SEL from RDS-equipped FM radio stations. To activate RDS: • When in FM mode, press the MENU control until RDS OFF displays. • Press the SEL control to engage this feature (RDS ON). RDS features: Once the RDS feature is on, press the MENU control to scroll through the following selections: Traffic announcements This feature allows you to hear traffic announcements while in CD mode.
Entertainment systems Press the MENU control until FIND program type is displayed. MENU + SEL Use the SEL control to select the program type. With the feature on, use the SEEK or SCAN control to find the desired program type from the following selections: • Classic • Country • Info • Jazz • Oldies • R&B • Religious • Rock • Soft • Top 40 Show This feature allows you to select the type of RDS broadcast information the radio will regularly show in the display.
Entertainment systems REAR SEAT ENTERTAINMENT SYSTEM Quick Start — How to get going To operate the system: 1. Your AutoVision威 system is automatically activated when the vehicle ignition and the audio system are ON. 2. If a movie is desired, insert a VHS cassette into the VCP and the video should start playing. 3. Press the MEDIA control to toggle to any other desired media source.
Entertainment systems To play a video game: 1. Connect the video line from your game device to the VIDEO jack. 2. Connect the left and right audio cables to the left (L) and right (R) audio jacks. 3. Ensure that the system is in AUX mode. The LCD screen will turn on and the AUX indicator will illuminate. / control and plug a 3.5mm headphone into 4. If desired, press the the headphone jack. With the headphones ON, the rear speakers will not operate.
Entertainment systems Do not attempt to service, repair or modify the AutoVision威 System. See your Ford or Lincoln Mercury dealer. Do not insert foreign objects into the videocassette player (VCP) tape cassette compartment. The front glass on the liquid crystal display may break when hit with a hard surface. If the glass breaks, do not touch the liquid crystalline material. In case of contact with skin, wash immediately with soap and water.
Entertainment systems the instructions, may cause harmful interference and radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to consult the dealer or an experienced radio/TV technician for help.
Entertainment systems Humidity and moisture condensation Moisture in the air will condense in the VCP under extremely humid conditions or when moving from a cold place to a warm one. Moisture condensation on the tape playback head drum may damage the videocassette and/or drum. If moisture condensation occurs, do not insert a videocassette into the player. If a videocassette is already in the player, remove it. Turn the VCP power ON to dry the moisture before inserting a videocassette.
Entertainment systems AutoVision姞 system Features • 2–head hi-fi playback • AutoPlay feature • Digital auto tracking • Dual stereo headphone with electric volume control • Self docking connection for easy mobile installation • Latching system for secure safety • Carrying handle for portability • Water resistant tape door • On screen display • Protection circuits Playback and format • The videocassette player of your AutoVision威 system can only be used in the “playback” mode.
Entertainment systems VCP controls 2 1 8 5 4 6 7 3 1. LED display The display lamp will light up in green when power is supplied to the videocassette player. 2. POWER key Press to toggle between ON/OFF. When the power is ON, other keys (PLAY, FF, REW, STOP) will illuminate. 3. PLAY key Press to playback a videocassette tape. 4. REWIND/REVIEW button Press to enter the reverse picture mode when in PLAYBACK mode. If in STOP mode, the tape will rewind at a high speed. 5.
Entertainment systems Remote control The remote control enables third row passengers to control the rear seat entertainment system. The remote control will not operate from the second row seats. The sensor for the remote control is located on the rear of the entertainment system. 1 2 3 4 5 6 7 8 9 10 1. POWER button Press to turn the videocassette player (VCP) ON or OFF. 2. ENCORE button Press to reverse the casssette for 5 seconds. Normal playback will then resume when in PLAYBACK mode. 3.
Entertainment systems 5. TRACKING + button Press for manual tape tracking. 6. TRACKING — button Press for manual tape tracking. 7. PLAY button Press to play the tape. 8. REW button Press to rewind the tape. 9. FF button Press to fast forward the tape. 10. STOP button Press to stop the tape. Battery replacement Batteries are supplied with the remote control unit. However, they are simply for operation check and will only work for a short time.
Entertainment systems The remote control unit uses two AAA batteries. The need for battery replacement is usually indicated if the remote control only functions at extremely close distances to the entertainment center or not at all. When replacing batteries, use two new batteries (alkaline recommended) and install with correct orientation (+ and − polarities). Ensure that you use only new batteries of the same brand.
Entertainment systems Press the memory preset controls 3 1 2 3 4 5 6 and 5 simultaneously on the front audio controls to disable the AutoVision威 controls. They will remain disabled until the front seat passengers “enable” them again by simultaneously pressing the 3 and 5 preset controls. The settings of the front seat controls will always override those of the rear seat controls. Adjusting the volume This control allows the rear seat passengers to adjust the volume level of the audio system.
Entertainment systems Using headphones/Personal Audio Feature The Personal Audio Feature allows the rear seat passengers to listen to one media source (radio, TAPE, CD, CDDJ, VCP, or AUX) while the front seat passengers listen to another. / To activate, press the control and plug a 3.5mm headphone into the headphone jack. With the headphones ON, the rear speakers will not operate. Press the MEDIA control to toggle to the desired media source.
Entertainment systems Media select Press the MEDIA control to toggle between AM, FM1, FM2, TAPE, CD, CDDJ, VCP and AUX modes. When selected, the media source will illuminate.
Entertainment systems Memory preset control In radio mode, press the MEM (Memory) control successively to scroll through the memory presets in AM, FM1 or FM2. In CDDJ mode, press the MEM (Memory) control to select the next disc in the compact disc changer. Play will begin with the first track. Seek function The SEEK control has varying functions depending on which mode is enabled. In radio mode (AM, FM1, FM2): control to find the Press the next listenable station down the frequency band.
Entertainment systems Flip-down screens The screens rotate down to view and up into the housing to store when not in use. Ensure that the screens are latched into the housing when being stored. 1 3 2 1. 6.4” (diagonal) color liquid crystal display (LCD) screen. 2. Screen housing. 3. Dimmer switch. Rotate to increase/decrease the brightness of the screen. General operation • When the engine is not running, use the system sparingly otherwise it will run the battery down.
Entertainment systems • When the ignition is turned ON, audio is through the headphones as LOW volume. Press the (+) control to increase volume. To listen ) through the vehicle’s speaker system, press the speaker button ( on the media control panel. Inserting/removing cassette Inserting cassette • Open the AutoVision威 console cover. • Insert the videocassette into the cassette compartment.
Entertainment systems On-screen indicators Playback operation 1. Press the POWER control on the VCP. 2. Insert a videocassette into the VCP. 3. The videocassette should automatically begin playback, and the picture will appear within approximately nine seconds. 4. Press the STOP control to stop playback or press EJECT to remove the cassette. Fast-forward or rewind (no picture) 1. Press the FF/REW control on the VCP. 2. Press the STOP control to stop or press EJECT to remove the cassette.
Entertainment systems Encore (on remote control) • Press the ENCORE control while in playback mode. The VCP will reverse to the previous five seconds of the selection and then operate at normal playback mode. Auxiliary input jacks The auxiliary input jacks on the AutoVision威 control panel accepts video and audio connectors for all standard video games (Nintendo威, PlayStation威, etc.) Other compatible devices such as DVD players, camcorders and portable CD players can also be connected to the auxiliary jacks.
Entertainment systems Video source selection The MEDIA control determines which video (VCP or Auxiliary input) is seen on the AutoVision威 screen. When the vehicle ignition is ON and the system is not in VCP mode, the AutoVision威 selects the Auxiliary input as the video source. (If there is not a video source connected to the Auxiliary input jack, the screen will be blank.) AutoPlay feature Your AutoVision威 system is equipped with an AutoPlay Feature.
Entertainment systems The following are some possible messages that may illuminate on your LED display and their meanings. Illuminates when there is a videocassestte in the system during power off. Illuminates when there is a videocassette in the system during power on. Illuminates when a videocassette is ejected from the system. Flashes during emergency mode. Illuminates during power on when there is not a videocassette present in the system.
Entertainment systems Illuminates when the videocassette is in STIL (pause) mode. Illuminates when the videocassette is in PLAY mode. Illuminates when the videocassette is in REV (review) mode. Illuminates when the videocassette is in CUE mode. Flashes separately when the videocassette is in ENCORE mode. Displays when: • the thermistor detects an extremely high or low temperature • the dew sensor is activated for high humidity In-home use Your AutoVision威 system is UL registered for in-home use.
Entertainment systems To re-install the VCP in your vehicle, insert the VCP into the console and push lightly until the VCP clicks into place. To use the AutoVision威 system in your home, you will need: • 12 V DC power converter rated for 1.5 amps/min • Patch cords with RCA style connectors These parts are available in your local electronics store or call toll free 1 (877) 848–6434 for assistance. Auxiliary jacks for home use 1.
Entertainment systems 1. VIDEO IN Connect this terminal to the AUDIO OUT terminal of your other apparatus (DVD, game machine, etc.). 2. AUDIO IN LR Connect these terminal(s) to the AUDIO OUT terminals of your other apparatus (DVD, game machine, etc.). 3. Plug headphones into these jacks. 3 1 2 TROUBLESHOOTING THE CD PLAYER (IF EQUIPPED) The laser beam used in the compact disc player is harmful to the eyes. Do not attempt to disassemble the case.
Entertainment systems CLEANING COMPACT DISCS Inspect all discs for contamination before playing. If necessary, clean discs only with an approved CD cleaner and wipe from the center out to the edge. Do not use circular motion. CD AND CD PLAYER CARE • Handle discs by their edges only. Never touch the playing surface. • Do not insert more than one disc at a time. • Do not expose discs to direct sunlight or heat sources for extended periods of time. • After playing, store the disc in its case.
Entertainment systems RADIO FREQUENCY INFORMATION The Federal Communications Commission (FCC) and the Canadian Radio and Telecommunications Commission(CRTC) establish the frequencies AM and FM stations may use for their broadcasts. Allowable frequencies are: AM 530, 540–1600, 1610 kHz FM 87.7, 87.9–107.7, 107.9 MHz Not all frequencies are used in a given area. RADIO RECEPTION FACTORS Three factors can affect radio reception: • Distance/strength. The further an FM signal travels, the weaker it is.
Climate controls HEATER ONLY SYSTEM (IF EQUIPPED) FAN HI OFF FLR LO MIX VENT COOL WARM Fan speed control Controls the volume of air circulated in the vehicle. FAN HI LO Temperature control knob Controls the temperature of the airflow inside the vehicle. On heater-only systems, the air cannot be cooled below the outside temperature. COOL WARM Mode selector control OFF Controls the direction of the airflow MIX FLR to the inside of the vehicle.
Climate controls Operating tips • In humid weather, place the climate control system in DEF before driving. This will reduce fogging on your windshield. Once the windshield has been cleared, select any desired position. • To reduce humidity buildup inside the vehicle, do not drive with the climate control system in the OFF position. • Under normal weather conditions, your vehicle’s climate control system should be left in any position other than OFF position when the vehicle is parked.
Climate controls Fan speed control Controls the volume of air circulated in the vehicle. FAN HI LO Temperature control knob Controls the temperature of the airflow inside the vehicle. COOL WARM Mode Selector Control Controls the direction of the airflow OFF to the inside of the vehicle. FLR VENT The air conditioning compressor can MIX NORM operate in all modes except VENT A/C and FLR. However, the air MAX conditioning will only function if the A/C outside temperature is about 6°C (43°F) or higher.
Climate controls • NORM A/C – Uses outside air to cool the vehicle. It is quieter than MAX A/C but not as economical. Airflow will be from the instrument panel registers. • VENT – Distributes outside air through the instrument panel registers. However, the air will not be cooled below the outside temperature because the air conditioning does not operate in this mode. • OFF – Outside air is shut out and the fan will not operate.
Climate controls • Under normal weather conditions, your vehicle’s climate control system should be left in any position other than the MAX A/C or OFF when the vehicle is parked. This allows the vehicle to “breathe” through the outside air inlet duct. • Under snowy or dirty weather conditions, your vehicle’s climate control system should be left in the OFF position when the vehicle is parked. This allows the climate control system to be free from contamination of outside pollutants.
Climate controls AUXILIARY HEATER AND AIR CONDITIONER (IF EQUIPPED) If your vehicle is equipped with a factory installed auxiliary unit, the main climate control panel will include separate controls for the front fan speed and the rear fan speed. In conjunction with the front fan speed control, an additional fan speed control is located overhead between the second and third row seating.
Climate controls Air temperature and air distribution are dependent upon the mode that is selected on the main climate control panel: • MAX A/C-Distributes recirculated air conditioning through the overhead vents of the rear compartment. • NORM A/C-Distributes recirculated air conditioning through the overhead vents of the rear compartment. • VENT-Distributes recirculated ambient air through the overhead vents of the rear compartment.
Lights HEADLAMP CONTROL • Pull the headlamp control toward you to the first position to turn on the parking lamps, tail lamps, license plate lamps and marker lamps. • Pull the headlamp control toward you to the outer position to turn on the headlamps (in addition to the previous lamps). Daytime running lamps (DRL) (if equipped) Turns the headlamps on with a reduced output. To activate: • the ignition must be in the ON position and • the headlamp control is in the OFF or Parking lamps position.
Lights Flash to pass Pull toward you to activate and release to deactivate. PANEL DIMMER CONTROL To adjust the brightness of the instrument panel: • Rotate clockwise/counterclockwise when the headlamp control is in the parking lamp or low-beam position. To turn on the courtesy lamp, cargo lamps or the dome lamp: • Rotate fully counterclockwise. The dome lamp will not illuminate if the control switch is in the OFF position.
Lights INTERIOR LAMPS DOOR OFF ON Cargo and dome lamps Rear cargo lamps equipped with an ON/OFF/DOOR control will light when: • doors are closed and the control is in the ON position • control is in the DOOR position and any door is open • headlamp control is rotated fully counterclockwise When the control is in the OFF position, it will not illuminate when you open the doors or fully rotate the headlamp control. Front and rear courtesy/reading lamps Rotate the lens to illuminate the lamp.
Lights BULBS Replacing exterior bulbs Check the operation of the following lamps frequently: • Headlamps • Tail lamps • Brakelamps • High-mount brakelamp • Turn signals • Backup lamps • License plate lamp Do not remove lamp bulbs unless they will be replaced immediately. If a bulb is removed for an extended period of time, contaminants may enter the lamp housings and affect performance. Using the right bulbs Replacement bulbs are specified in the chart below.
Lights Function Number of Trade number bulbs Map/reading lamp 2 211-2 All replacement bulbs are clear in color except where noted. To replace all instrument panel lights - see your dealer Replacing headlamp bulbs (aerodynamic) To remove the headlamp bulb: 1. Make sure headlamp switch is in OFF position. 2. Open the hood. 3. Push each clip tab toward the engine compartment and lift upward to the stop position. 4. Remove the headlamp assembly. 5.
Lights To install the new bulb: Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated. 1. With the flat side of the bulb’s plastic base facing upward, insert the glass end of the bulb into the lamp assembly. You may need to turn the bulb left or right to align the grooves in the plastic base with the tabs in the lamp assembly.
Lights 4. Remove the four headlamp bulb retaining screws. 5. Disconnect the electrical connector from the bulb. 6. Remove the headlamp. To install the new bulb, follow the removal procedures in reverse order. Replacing front parking lamp/turn signal bulbs 1. Make sure the headlamp control is in the OFF position. 2. Open the hood. 3. Remove two screws and pull lamp assembly away from the vehicle. 4. Rotate the bulb socket counterclockwise and remove. 5.
Lights To change the high-mount brakelamp bulbs: 1. Remove the two screws from the high-mount brakelamp assembly. 2. Remove the bulb from the lamp assembly by turning counterclockwise. 3. Carefully pull the bulb straight out of the socket and push in the new bulb. 4. Install bulb socket in lamp assembly by turning clockwise. 5. Install brakelamp assembly on the vehicle with two screws. Replacing license plate lamp bulbs To change the license plate bulbs: 1.
Lights Replacing tail lamp/turn/backup lamp bulbs The tail lamp/turn/backup lamp bulbs are located the tail lamp assembly, one just below the other. Follow the same steps to replace either bulb: 1. Remove the four screws and the lamp assembly from vehicle. 2. Rotate bulb socket counterclockwise and remove from lamp assembly. 3. Carefully pull the bulb straight out of the socket and push in the new bulb. 4. Install the bulb socket in lamp assembly by turning clockwise. 5.
Driver controls WINDSHIELD WIPER/WASHER CONTROLS Rotate the windshield wiper control to the desired interval, low or high speed position. The bars of varying length are for intermittent wipers. When in this position rotate the control upward for fast intervals and downward for slow intervals. Push the control on the end of the stalk to activate washer. Push and hold for a longer wash cycle. The washer will automatically shut off after ten seconds of continuous use.
Driver controls Changing the wiper blades To replace the wiper blades: 1. Pull the wiper arm away from the windshield and lock into the service position. 2. Turn the blade at an angle from the wiper arm. Push the lock pin manually to release the blade and pull the wiper blade down toward the windshield to remove it from the arm. 3. Attach the new wiper to the wiper arm and press it into place until a click is heard.
Driver controls Never adjust the steering wheel when the vehicle is moving. AUXILIARY POWER POINT Power outlets are designed for accessory plugs only. Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power outlet can cause damage not covered by your warranty. The auxiliary power point is located on the instrument panel. A second power point (if equipped) is located behind the driver’s seat on the upper trim panel.
Driver controls • Press the bottom portion of the rocker switch to open. POWER SIDE VIEW MIRRORS (IF EQUIPPED) The ignition may be in any position to adjust the power side view mirrors. To adjust your mirrors: to adjust the left 1. Select mirror or to adjust the right mirror. 2. Move the control in the direction you wish to tilt the mirror. 3. Return to the center position to lock mirrors in place.
Driver controls Fold-away mirrors Pull the side mirrors in carefully when driving through a narrow space, like an automatic car wash. SPEED CONTROL (IF EQUIPPED) To turn speed control on • Press ON. Vehicle speed cannot be controlled until the vehicle is traveling at or above 48 km/h (30 mph). Do not shift the gearshift lever into N (Neutral) with the speed control on. ON OFF Do not use the speed control in heavy traffic or on roads that are winding, slippery, or unpaved.
Driver controls To set a speed • Press SET ACCEL. For speed control to operate, the speed control must be ON and the vehicle speed must be greater than 48 km/h (30 mph). RES SET ACCEL COAST If you drive up or down a steep hill, your vehicle speed may vary momentarily slower or faster than the set speed. This is normal. Speed control cannot reduce the vehicle speed if it increases above the set speed on a downhill.
Driver controls To set a higher set speed • Press and hold SET ACCEL. Release the control when the desired vehicle speed is reached RES or • Press and release SET ACCEL to SET ACCEL operate the Tap-Up function. Each press will increase the set COAST speed by 1.6 km/h (1 mph) or • Accelerate with your accelerator pedal. When the desired vehicle speed is reached, press and release SET ACCEL. You can accelerate with the accelerator pedal at any time during speed control usage.
Driver controls To disengage speed control • Depress the brake pedal. Disengaging the speed control will not erase the previously programmed set speed. Pressing OFF will erase the previously programmed set speed. ON OFF To return to a previously set speed • Press RES. For RES to operate, the vehicle speed must be faster than 48 km/h (30 mph).
Driver controls OVERDRIVE CONTROL Activating overdrive (Overdrive) is the normal drive position for the best fuel economy. The overdrive function allows automatic upshifts and downshifts through all available gears. Deactivating overdrive Press the Transmission Control Switch (TCS) located on the end of OVERDRIVE the gearshift lever. The Transmission Control Indicator Light (TCIL) (the word OFF) will illuminate on the end of the gearshift lever. The transmission will operate in all gears except overdrive.
Driver controls Storage compartment (if equipped) Press the OPEN control to open the storage compartment. The door will open slightly and can be moved to full open. The storage compartment may be used to secure sunglasses or a similar object. Installing a garage door opener (if equipped) The storage compartment can be converted to accommodate a variety of aftermarket garage door openers: • Remove the storage clip from the door.
Driver controls • Place the provided height adaptors onto the back of the GARAGE control as needed. • Press the GARAGE control to activate the transmitter. Electronic compass/temperature display (if equipped) Outside air temperature The outside temperature display is contained in the overhead console unless the vehicle is equipped with an EATC system. Refer to Electric automatic temperature control in the Climate controls chapter.
Driver controls The compass reading may be affected when you drive near large buildings, bridges, power lines and powerful broadcast antenna. Magnetic or metallic objects placed in or on the vehicle may also affect compass accuracy. Adjustments may need to be made to the zone and calibration of the compass. Compass zone adjustment 1. Determine which magnetic zone you are in by referring to the zone map. 2. Turn the ignition to the ON position. 1 15 2 14 3 13 4 12 11 5 6 10 7 3.
Driver controls Compass calibration adjustment Perform this adjustment in an open area free from steel structures and high voltage lines: • Press and hold the SELECT control until CAL appears in the display (approximately eight seconds) and release. • Drive the vehicle slowly (less than 5 km/h [3 mph]) in circles until CAL indicator turns off in about 2–3 complete circles. • The compass is now calibrated.
Driver controls • To open, lift the cargo organizer up to the upright position, pull the front panel away from the rear panel sliding it to the right until it locks. • To close, press the release button, slide the front panel towards the rear panel and fold down to the stowed position. • To remove, lift the cargo organizer up to the upright position, unscrew the screw caps on each side of the organizer and remove.
Locks and security KEYS The key operates all locks on your vehicle. In case of loss, replacement keys are available from your dealer. You should always carry a second key with you in a safe place in case you require it in an emergency. POWER DOOR LOCKS (IF EQUIPPED) Press U to unlock all doors and L to lock all doors. U L Memory lock If you lock your doors with the power lock switch or the remote transmitter while the sliding door is open, the door will automatically lock after it is closed.
Locks and security REMOTE ENTRY SYSTEM (IF EQUIPPED) This device complies with part 15 of the FCC rules and with RS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Locks and security Locking the doors Press this control to lock all doors. To confirm all doors are closed and locked, press the control a second time within three seconds. The doors will lock again and the horn will chirp. Sounding a panic alarm Press this control to activate the alarm. To deactivate the alarm, press the control again or turn the ignition to ACC or ON. Replacing the battery The transmitter is powered by one coin type three-volt lithium battery CR2032 or equivalent.
Locks and security To replace the battery: 1. Twist a thin coin between the two halves of the transmitter near the key ring. DO NOT TAKE THE FRONT PART OF THE TRANSMITTER APART. 2. Place the positive (+) side of new battery UP. Refer to the diagram inside the transmitter unit. 3. Snap the two halves back together. Replacement of the battery will not cause the remote transmitter to become deprogrammed from your vehicle. The remote transmitter should operate normally after battery replacement.
Locks and security Illuminated entry The interior lamps illuminate when the remote entry system is used to unlock the door(s) or sound the personal alarm. The system automatically turns off after 25 seconds or when the ignition is turned to the RUN or ACC position. The dome lamp control (if equipped) must not be set to the OFF position for the illuminated entry system to operate.
Seating and safety restraints SEATING Adjusting the front manual seat Never adjust the driver’s seat or seatback when the vehicle is moving. Do not pile cargo higher than the seatbacks to reduce the risk of injuring people in a collision or sudden stop. Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Reclining the seatback can reduce the effectiveness of the seat’s safety belt in the event of a collision. Lift handle to move seat forward or backward.
Seating and safety restraints Pull lever up to adjust seatback. Using the manual lumbar support The lumbar support control is located on the inboard side of the driver’s seat. Turn the lumbar support control clockwise to increase firmness. Turn the lumbar support control counterclockwise to increase softness. Adjusting the front power seat (if equipped) Never adjust the driver’s seat or seatback when the vehicle is moving.
Seating and safety restraints Press to raise or lower the front portion of the seat cushion. Press to raise or lower the rear portion of the seat cushion. Press the control to move the seat forward, backward, up or down.
Seating and safety restraints Quick release captains chair To remove the seat: 1. Disengage the lap/shoulder belt from the seat by inserting a key or small screwdriver into the slot in the detachable anchor and lifting upward. Stow the tongue end of the detachable anchor.
Seating and safety restraints 2. Pull the seat latch handle, then pull the seat toward the right side of the vehicle to disengage four pins from the floor mount. 3. Remove the seat. To install the seat: Check to see that the seat and seatback is latched securely in position. Keep floor area free of objects that would prevent proper seat engagement. Never attempt to adjust the seat while the vehicle is in motion. 1. Position the seat to the floor mount. 2.
Seating and safety restraints ACCESSING THE 3RD, 4TH AND 5TH ROW SEATS (IF EQUIPPED) Stow the 2nd row passenger side seat belt on the overhead hook to make access to the rear seats easier. To make access to the 4th and 5th row seats easier, attach the 3rd and 4th row passenger side seat belts to the trim panel by using the snaps attached to the seat belt webbing and the trim panel.
Seating and safety restraints REAR BENCH SEAT To remove the seats: 1. Disengage the lap/shoulder belt from the seat by inserting a key or small screwdriver into the slot in the detachable anchor and lifting upward (2nd row passenger side only). Stow the tongue end of the detachable anchor (2nd row only).
Seating and safety restraints 2. Pull the LH/RH seat latch handles, located under the seat, rearward to release the latch hook ends from the front strikers. 3. Move the seat rearward and lift the seats rear hooks away from the rear strikers prior to lifting the front hooks out from the front strikers. 4. With assistance, remove the seat assembly. • To remove the 3rd, 4th, and 5th row seats (if equipped), repeat steps 2 through 4. To install the seat: 1. Position the seat in the vehicle. 2.
Seating and safety restraints SAFETY RESTRAINTS Safety restraints precautions Always drive and ride with your seatback upright and the lap belt snug and low across the hips. To reduce the risk of injury, make sure children sit where they can be properly restrained. Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision.
Seating and safety restraints Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints. Combination lap and shoulder belts 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle. 2. To unfasten, push the release button and remove the tongue from the buckle.
Seating and safety restraints Automatic locking mode In this mode, the shoulder belt is automatically pre-locked. The belt will still retract to remove any slack in the shoulder belt. The automatic locking mode is not available on the driver safety belt. When to use the automatic locking mode • Any time a child safety seat is installed in a passenger front or outboard rear seating position (if equipped). Children 12 years old and under should be properly restrained in the rear seat whenever possible.
Seating and safety restraints How to disengage the automatic locking mode Ford recommends that all safety belt assemblies and attaching hardware should be inspected by a qualified technician after any collision. Safety belt assemblies not in use during a collision should also be inspected and replaced if either damage or improper operation is noted.
Seating and safety restraints Failure to replace the safety belt assembly under the above conditions could result in severe personal injuries in the event of a collision. Front safety belt height adjustment Your vehicle has safety belt height adjustments for the driver and front passenger. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder. To lower the shoulder belt height, push the button and slide the height adjuster down.
Seating and safety restraints Insert the tongue into the correct buckle (the buckle closest to the direction the tongue is coming from). To lengthen the belt, turn the tongue at a right angle to the belt and pull across your lap until it reaches the buckle. To tighten the belt, pull the loose end of the belt through the tongue until it fits snugly across the hips. Shorten and fasten the belt when not in use.
Seating and safety restraints Conditions of operation If... The driver’s safety belt is not buckled before the ignition switch is turned to the ON position... The driver’s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding... The driver’s safety belt is buckled before the ignition switch is turned to the ON position... Then... The safety belt warning light illuminates and the warning chime sounds 4-8 seconds.
Seating and safety restraints If... The driver’s safety belt is buckled before the ignition switch is turned to the ON position... Then... The BeltMinder feature will not activate. The purpose of the BeltMinder is to remind occasional wearers to wear safety belts all of the time. The following are reasons most often given for not wearing safety belts: (All statistics based on U.S. data) Reasons given...
Seating and safety restraints Reasons given... “Belts wrinkle my clothes” “The people I’m with don’t wear belts” “I have an air bag” “I’d rather be thrown clear” Consider... Possibly, but a serious crash can do much more than wrinkle your clothes, particularly if you are unbelted. Set the example, teen deaths occur 4 times more often in vehicles with TWO or MORE people. Children and younger brothers/sisters imitate behavior they see. Air bags offer greater protection when used with safety belts.
Seating and safety restraints • • • • the ignition switch is in the OFF position all vehicle doors are closed the driver’s safety belt is unbuckled the parklamps/headlamps are in OFF position (If vehicle is equipped with Autolamps, this will not affect the procedure.) To reduce the risk of injury, do not deactivate/activate the Belt Minder feature while driving the vehicle. 1. Turn the ignition switch to the RUN (or ON) position. (DO NOT START THE ENGINE) 2.
Seating and safety restraints Safety belt extension assembly If the safety belt is too short when fully extended, there is a 20 cm (8 inch) safety belt extension assembly that can be added (part number 611C22). This assembly can be obtained from your dealer at no cost. Use only extensions manufactured by the same supplier as the safety belt. Manufacturer identification is located at the end of the webbing on the label.
Seating and safety restraints AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) Your vehicle is equipped with a crash sensing and diagnostic module which records information about the air bag and sensor systems. In the event of a collision this module may save information related to the collision including information about the air bag system and impact severity.
Seating and safety restraints All occupants of the vehicle, including the driver, should always properly wear their safety belts, even when an air bag (SRS) is provided. Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints. National Highway Traffic Safety Administration (NHTSA) recommends a minimum distance of at least 25 cm (10 inches) between an occupant’s chest and the driver air bag module.
Seating and safety restraints Additional equipment may affect the performance of the air bag sensors increasing the risk of injury. Please refer to the Body Builders Layout Book for instructions about the appropriate installation of additional equipment. Children and air bags For additional important safety information, read all information on safety restraints in this guide. Children must always be properly restrained.
Seating and safety restraints How does the air bag supplemental restraint system work? The air bag SRS is designed to activate when the vehicle sustains longitudinal deceleration sufficient to cause the sensors to close an electrical circuit that initiates air bag inflation. The fact that the air bags did not inflate in a collision does not mean that something is wrong with the system. Rather, it means the forces were not of the type sufficient to cause activation.
Seating and safety restraints The SRS consists of: • driver and passenger air bag modules (which include the inflators and air bags) • one or more impact and safing sensors • a readiness light and tone • a diagnostic module • and the electrical wiring which connects the components The diagnostic module monitors its own internal circuits and the supplemental air bag electrical system warning (including the impact sensors), the system wiring, the air bag system readiness light, the air bag back up power and t
Seating and safety restraints Disposal of air bags and air bag equipped vehicles (including pretensioners) For disposal of air bags or air bag equipped vehicles, see your local dealership or qualified technician. Air bags MUST BE disposed of by qualified personnel. SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safety restraints for children. Also see Air bag supplemental restraint system (SRS) in this chapter for special instructions about using air bags.
Seating and safety restraints Any booster seat that places the vehicle’s lap belt or shoulder belt around a shield above and ahead of the child’s hips should not be used in this vehicle. Do not use a forward–facing safety seat or an infant seat in the last row of a 12– or 15–passenger Club Wagon. Children and safety belts If the child is the proper size, restrain the child in a safety seat.
Seating and safety restraints SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child. Carefully follow all of the manufacturer’s instructions with the safety seat you put in your vehicle. If you do not install and use the safety seat properly, the child may be injured in a sudden stop or collision.
Seating and safety restraints • Put the safety belt in the automatic locking mode. Refer to Automatic locking mode (passenger side front and outboard rear seating positions) (if equipped). Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is capable of providing a tether anchorage. For more information on top tether straps, refer to Attaching safety seats with tether straps.
Seating and safety restraints 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together. 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until you hear a snap and feel the latch engage.
Seating and safety restraints 5. To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode. 7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with your knee on the child seat. 8.
Seating and safety restraints Attaching safety seats with tether straps Children should be placed in the rear in an appropriate child safety seat that is properly secured to the vehicle. When using forward-facing child safety seats in vehicles with only two seating positions so the forward-facing child safety seat cannot be placed in the rear of the vehicle, move the passenger seat as far back from the instrument panel as possible.
Seating and safety restraints 3. Route the child safety seat tether strap over the back of the front right-hand passenger seat as shown. 4. Clip the tether strap hook to the seat pedestal to the location shown. 5. Adjust the front right hand passenger seat to the full rearward position.
Seating and safety restraints 6. Refer to the instructions in this section under Installing child safety seats in combination lap and shoulder belt seating positions to secure the child safety seat. 7. Tighten the child safety seat tether strap according to the manufacturer’s instructions. Second row bucket seats (Chateau Quads) The tether strap can be attached directly to the tether bracket under the back edge of the seat cushion. 1.
Seating and safety restraints 3. Clip the tether strap hook to the seat pedestal at the location shown. 4. Refer to the instructions in this section under Installing child safety seats in combination lap and shoulder belt seating positions to secure the child safety seat. 5. Tighten the child safety seat tether strap according to the manufacturer’s instructions.
Seating and safety restraints 2. Route the child safety tether strap over the back of 3–Passenger bench seat. 3. Clip the tether strap hook to the tether bracket mounted under rear rail of seat cushion frame. 4. Refer to the instructions in this section under installing child safety seats in combination lap and shoulder belt seating positions to secure the child safety seat. 5. Tighten the child safety seat tether strap according to the manufacturer’s instructions.
Driving STARTING Positions of the ignition 1. ACCESSORY, allows the electrical 4 accessories such as the radio to 3 operate while the engine is not 5 running. 2. LOCK, locks the steering wheel, 2 automatic transmission gearshift lever and allows key removal. 1 3. OFF, shuts off the engine and all accessories without locking the steering wheel. 4. ON, all electrical circuits operational. Warning lights illuminated. Key position when driving. 5. START, cranks the engine.
Driving Do not start your vehicle in a closed garage or in other enclosed areas. Exhaust fumes can be toxic. Always open the garage door before you start the engine. See Guarding against exhaust fumes in this chapter for more instructions. If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately. Do not drive if you smell exhaust fumes. Important safety precautions A computer system controls the engine’s idle revolutions per minute (RPM).
Driving 5. Turn the key to 4 (ON) without turning the key to 5 (START). 4 If there is difficulty in turning the 3 key, firmly rotate the steering wheel 5 left and right until the key turns freely. This condition may occur 2 when: • front wheels are turned 1 • front wheel is against the curb • steering wheel is turned when getting in or out of the vehicle Make sure the corresponding lights illuminate or illuminate briefly. If a light fails to illuminate, have the vehicle serviced. light may not illuminate.
Driving 3. If the temperature is below -12° C (10° F) and the engine does not start in 15 seconds on the first try, turn the key OFF and wait 10 seconds and try again. If the engine does not start in two attempts, press the accelerator pedal all the way to floor and hold. Turn the key to START position. 4. When the engine starts, release the key, then release the accelerator pedal gradually as the engine speeds up. 5. After idling for a few seconds, apply the brake and release the parking brake.
Driving WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Driving in the steering wheel while braking, the vehicle should be inspected by a qualified service technician. The ABS operates by detecting the onset of wheel lockup during brake applications and compensates for this tendency. The wheels are prevented from locking even when the brakes are firmly applied. The accompanying illustration depicts the advantage of an ABS equipped vehicle (on bottom) to a non-ABS equipped vehicle (on top) during hard braking with loss of front braking traction.
Driving Parking brake Apply the parking brake whenever the vehicle is parked. Push pedal downward to set the parking brake. The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned ON) until the parking brake is released. Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn off the ignition whenever you leave your vehicle. The parking brake is not recommended to stop a moving vehicle.
Driving STEERING Your vehicle is equipped with power steering. Power steering uses energy from the engine to help steer the vehicle. To prevent damage to the power steering pump: • Never hold the steering wheel to the extreme right or the extreme left for more than a few seconds when the engine is running. • Do not operate the vehicle with a low power steering pump fluid level (below the MIN mark on the reservoir).
Driving PREPARING TO DRIVE YOUR VEHICLE Utility vehicles have a significantly higher rollover rate than other types of vehicles. In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Your vehicle has special design and equipment features to make it capable of performing in a wide variety of circumstances.
Driving If you cannot move the gearshift lever out of P (Park) with ignition in the ON position and the brake pedal depressed: 1. Apply the parking brake, turn ignition key to LOCK, then remove the key. 2. Insert the key and turn it to OFF. Apply the brake pedal and shift to N (Neutral). 3. Start the vehicle. If it is necessary to use the above procedure to move the gearshift lever, it is possible that a fuse has blown or the vehicle’s brakelamps are not operating properly.
Driving Hold the brake pedal down while you move the gearshift lever from P (Park) to another position. If you do not hold the brake pedal down, your vehicle may move unexpectedly and injure someone. P (Park) Always come to a complete stop before shifting into P (Park). Make sure the gearshift lever is securely latched in P (Park). This position locks the transmission and prevents the rear wheels from turning. Always set the parking brake fully and make sure the gearshift lever is latched in P (Park).
Driving The transmission control indicator light (TCIL) (the word OFF) on the end of the gearshift lever will illuminate. OVERDRIVE Drive – Not shown on the display. Activate by pressing the transmission control switch (TCS) on the end of the gearshift lever with the gearshift position. The TCIL (the word OFF) will illuminate on the in the gearshift lever. Transmission operates in gears one through three.
Driving Forced Downshifts (Overdrive) or Drive (O/D OFF) when To gain acceleration in passing another vehicle, push the accelerator to the floor. The transmission will downshift to the appropriate gear: third, second or first gear. Shift strategy (4R100 automatic transmission) To account for customer driving habits and conditions, your 4R100 automatic transmission electronically controls the shift quality by using an adaptive learning strategy.
Driving • Base Curb Weight: Weight of the vehicle including any standard equipment, fluids, lubricants, etc. It does not include occupants or aftermarket equipment. • Payload: Combined maximum allowable weight of cargo, occupants and optional equipment. The payload equals the gross vehicle weight rating minus base curb weight. • GVW (Gross Vehicle Weight): Base curb weight plus payload weight. The GVW is not a limit or a specification.
Driving Do not use replacement tires with lower load carrying capacities than the originals because they may lower the vehicle’s GVWR and GAWR limitations. Replacement tires with a higher limit than the originals do not increase the GVWR and GAWR limitations. The Safety Certification Label, found on the driver’s door pillar, lists several important vehicle weight rating limitations. Before adding any additional equipment, refer to these limitations.
Driving Calculating the load your vehicle can carry/tow 1. Use the appropriate maximum gross combined weight rating (GCWR) chart to find the maximum GCWR for your type engine and rear axle ratio. 2. Weigh your vehicle as you customarily operate the vehicle without cargo. To obtain correct weights, try taking your vehicle to a shipping company or an inspection station for trucks. 3. Subtract your loaded vehicle weight from the maximum GCWR on the following charts.
Driving GCWR (Gross Combined Weight Rating)/Trailer Weights Trailer weight Maximum Rear Maximum range - kg frontal area of Engine axle GCWR - kg (lbs.) trailer - m2 ratio (lbs.) (ft2) (0-Maximum) Regular Van E-250 HD (3 901 kg [8 600 lb.]-3 924 kg [8 650 lb.] GVW) 4 990 4.2L 4.09 2 586 (5 700) 5.52 (60) (11 000) 5 897 5.4L 3.73 3 402 (7 500) 5.52 (60) (13 000) Super Van E-250 4 763 4.2L 3.73 2 313 (5 100) 5.52 (60) (10 500) 5 897 5.4L 3.73 3 357 (7 400) 5.
Driving GCWR (Gross Combined Weight Rating)/Trailer Weights Trailer weight Maximum Rear Maximum range - kg frontal area of Engine axle GCWR - kg (lbs.) trailer - m2 ratio (lbs.) (ft2) (0-Maximum) Super Van E-350 5 443 5.4L 3.55 2 858 (6 300) 5.52 (60) (12 000) 5 897 5.4L 4.10 3 311 (7 300) 5.52 (60) (13 000) 6 804 6.8L 3.73 4 173 (9 200) 5.52 (60) (15 000) 8 392 6.8L 4.10 4 536 (10 000) 5.52 (60) (18 500) E-150 8 passenger Wagon 4 536 4.2L 3.55 2 132 (4 700) 5.52 (60) (10 000) 5 216 4.6L 3.
Driving GCWR (Gross Combined Weight Rating)/Trailer Weights Trailer weight Maximum Rear Maximum range - kg frontal area of Engine axle GCWR - kg (lbs.) trailer - m2 ratio (lbs.) (ft2) (0-Maximum) E-350 8 passenger Wagon 5 443 5.4L 3.73 2 858 (6 300) 5.52 (60) (12 000) 6 804 6.8L 3.73 4 037 (8 900) 5.52 (60) (15 000) 8 392 6.8L 4.10 4 536 (10 000) 5.52 (60) (18 500) E-350 12 passenger Wagon 5 443 5.4L 3.55 2 722 (6 000) 5.52 (60) (12 000) 5 897 5.4L 4.10 3 175 (7 000) 5.52 (60) (13 000) 5 443 5.4L 3.
Driving GCWR (Gross Combined Weight Rating)/Trailer Weights Trailer weight Maximum Rear Maximum range - kg frontal area of Engine axle GCWR - kg (lbs.) trailer - m2 ratio (lbs.) (ft2) (0-Maximum) E-350 Cutaway (dual rear wheel) 5 897 5.4L 4.10 * 5.52 (60) (13 000) 8 392 6.8L 4.10 * 5.52 (60) (18 500) E-450 Cutaway (dual rear wheel) 9 072 6.8L 4.63 * 5.52 (60) (20 000) E-250/350 Stripped Chassis (single rear wheel-124ⴖwheelbase for E-250 only) 4 990 4.2L 4.09 1 090 (2 400) 5.52 (60) (11 000) 5 897 5.4L 4.
Driving GCWR (Gross Combined Weight Rating)/Trailer Weights Trailer weight Maximum Rear Maximum range - kg frontal area of Engine axle GCWR - kg (lbs.) trailer - m2 ratio (lbs.) (ft2) (0-Maximum) E-450 Stripped Chassis (dual rear wheel) 5 897 5.4L 4.10 1 361 (3 000) 5.52 (60) (13 000) 9 072 6.8L 4.63 * 5.
Driving Preparing to tow Use the proper equipment for towing a trailer, and make sure it is properly attached to your vehicle. See your dealer or a reliable trailer dealer if you require assistance. Hitches Do not use or install hitches that clamp onto the bumper or to the axle. Underbody hitches are acceptable if installed properly. Safety chains Always connect the trailer’s safety chains to the frame or hook retainers of the vehicle hitch.
Driving Using a step bumper (if equipped) The rear bumper is equipped with an integral hitch and only requires a ball with a 25.4 mm (one inch) shank diameter. The bumper has a 2 270 kg (5 000 lb.) trailer weight and 227 kg (500 lb.) tongue weight capacity. If it is necessary to relocate the trailer hitch ball position, a frame-mounted trailer hitch must be installed. Driving while you tow When towing a trailer: • Ensure that you turn off your speed control.
Driving • If you will be towing a trailer frequently in hot weather, hilly conditions, at GCW, or any combination of these factors, consider refilling your rear axle with synthetic gear lube. Refer to the Maintenance and specifications chapter for the lubricant specification. • After you have traveled 80 km (50 miles), thoroughly check your hitch, electrical connections and trailer wheel lug nuts.
Driving RECREATIONAL TOWING (ALL WHEELS ON THE GROUND) An example of recreational towing would be towing your vehicle on a trip behind a motorhome. Follow these guidelines if you have the need for recreational towing your vehicle with all four wheels on the ground. These guidelines are designed to ensure that your transmission is not damaged.
Roadside emergencies GETTING ROADSIDE ASSISTANCE To fully assist if you should have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New Vehicle Limited Warranty. The service is available: • 24–hours, seven days a week • for the Basic warranty period (Canada) or New Vehicle Limited Warranty period (U.S.
Roadside emergencies If you need to arrange roadside assistance for yourself, Ford Motor Company will reimburse a reasonable amount. To obtain reimbursement information, U.S. Ford or Mercury vehicles customers call 1-800-241-3673; Lincoln vehicle customers call 1–800–521–4140. Canadian customers who need to obtain reimbursement information, call 1–800–665–2006.
Roadside emergencies FUEL FUEL PUMP SHUT-OFF SWITCH RESET The fuel pump shut-off switch is a device intended to stop the electric fuel pump when your vehicle has been involved in a substantial jolt. After a collision, if the engine cranks but does not start, the fuel pump shut-off switch may have been activated. The fuel pump shut-off switch is located in the passenger’s foot well, behind the kick panel, except for commercial stripped chassis vehicles.
Roadside emergencies For commercial stripped chassis vehicles, the fuel pump shut-off switch is located on a bracket above the brake pedal. Use the following procedure to reset the fuel pump shut-off switch. 1. Turn the ignition to the OFF position. 2. Check the fuel system for leaks. 3. If no fuel leak is apparent, reset the fuel pump shut-off switch by pushing in on the reset button. 4. Turn the ignition to the ON position. Pause for a few seconds and return the key to the OFF position. 5.
Roadside emergencies FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within 15 the fuse. Check the appropriate fuses before replacing any electrical components. Note: Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire.
Roadside emergencies Passenger compartment fuse panel The fuse panel is located below and to the left of the steering wheel by the brake pedal. Remove the panel cover to access the fuses. To remove a fuse use the fuse puller tool provided on the fuse panel cover. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 The fuses are coded as follows.
Roadside emergencies Fuse/ Relay Location 3 Fuse Amp Rating 15A 4 15A 5 20A 6 10A 7 10A 8 30A 9 30A 10 20A 11 15A 12 15A 13 15A Passenger Compartment Fuse Panel Description Main Light Switch, RKE Module, Radio, Instrument Illumination, E Traveler VCP and video screens, Overhead Console Power Locks w/RKE, Illuminated Entry, Warning Chime, Modified Vehicle, Main Light Switch, Courtesy Lamps RKE Module, Power Lock Switches, Memory Lock, Power Locks with RKE Brake Shift Interlock, Speed Co
Roadside emergencies Fuse/ Relay Location 14 Fuse Amp Rating 5A 15 16 17 18 19 20 21 22 5A 30A — — 10A 5A 30A 15A 23 20A 24 25 26 27 28 29 30 — 10A 20A 5A 20A — 15A 31 10A 32 33 34 35 36 5A 20A 10A 30A 5A 37 38 20A 10A 180 Passenger Compartment Fuse Panel Description Instrument Cluster (Air Bag and Charge Indicator) Trailer Battery Charge Relay Power Seats Not Used Not Used Air Bag Diagnostic Monitor Overdrive Cancel Switch Power Windows* Memory Power Radio, E Traveler Radio, E Traveler Conso
Roadside emergencies Fuse/ Relay Fuse Amp Location Rating 39 20A 40 30A 41 30A 42 — 43 20A C.B. 44 — * Either Fuse 21 or Circuit breaker windows. Passenger Compartment Fuse Panel Description E Traveler Power Point #1 Modified Vehicle Modified Vehicle Not Used Power Windows* Not Used 43 will be present for power Power distribution box The power distribution box is located in the engine compartment.
Roadside emergencies H F J G K 23 E 22 15 29 21 14 27 20 13 25 19 12 28 18 11 26 17 10 24 16 9 B 8 A 1 C 3 2 5 6 7 D 4 The high-current fuses are coded as follows.
Roadside emergencies Fuse/Relay Location 12 Fuse Amp Rating 60A** 13 50A** 14 30A** 15 40A** 16 17 18 19 20 21 22 50A** 30A** 60A** 60A** 20A** 50A** 40A** 23 24 60A** 20A* 25 26 27 28 29 A B C D E F 20A* 10A* 15A* — — — — — — — — G — Power Distribution Box Description Engine Compartment Fuses 25, 27 Blower Motor Relay (Blower Motor) Trailer Running Lamps Relay, Trailer Backup Lamps Relay Main Light Switch, Daytime Running Lights (DRL) Auxiliary Blower Motor Relay Fuel Pump Relay I/P Fuses 4
Roadside emergencies Fuse/Relay Fuse Amp Location Rating H — J — K — * Mini Fuses ** Maxi Fuses Power Distribution Box Description Blower Motor Relay Horn Relay Fuel Pump Relay Relays Relays are located in the power distribution box and should be replaced by qualified technicians. CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily. Instead, gradually decrease your speed. Hold the steering wheel firmly and slowly move to a safe place on the side of the road.
Roadside emergencies 3. Remove the jack handle from the right side compartment and insert the tip of the jack handle through the access hole and into the tube. 4. Turn the jack handle counterclockwise until the cable is slack and the tire can be slid rearward from under the vehicle. 5. Remove the retainer from the spare tire. To stow the cable retainer with the spare removed, turn the jack handle clockwise until all slack is removed. To stow the spare tire: 1.
Roadside emergencies Tire change procedure Preparing to change the tire To prevent the vehicle from moving when you change a tire, be sure the parking brake is set, then block (in both directions) the wheel that is diagonally opposite (other side and end of the vehicle) to the tire being changed. 1. Park on a level surface. 2. Activate the warning flashers. 3. Place the gearshift in P (Park)(automatic transmission). 4. Apply the parking brake and turn engine OFF. 5.
Roadside emergencies 6. Remove the spare tire and jack from the storage location. 7. Use the tapered end of the lug nut wrench to unscrew wheel ornaments attached by retaining screws. Remove any wheel trim. Insert the tapered end of the lug nut wrench behind wheel covers or hubcaps and twist off. 8. Loosen the wheel nut by pulling up on the handle of the lug nut wrench about one-half turn (counterclockwise). Do not remove the wheel lug nuts until you raise the tire off the ground. Replacing the tire 1.
Roadside emergencies • Never use the front or rear differential as a jacking point.
Roadside emergencies Front axle jacking points: • All models Place the jack under the pin on the front surface of the front axle. Do not place the jack under or on the steering linkage. 3. Turn the jack handle clockwise until the wheel is completely off the ground. 4. Remove the lug nuts with the lug nut wrench. 5. Replace the flat tire with the spare tire. If your vehicle has single rear wheels, thread the lug nuts on the studs with the beveled face toward the wheel.
Roadside emergencies • 8-lug wheel Never use wheels or lug nuts different than the original equipment as this could damage the wheel or mounting system. This damage could allow the wheels to come off while the vehicle is being driven. 9. Replace any wheel covers, ornaments or hub caps. Make sure they are screwed or snapped in place. 10. Stow the jack, handle and lug wrench. 11. Unblock the wheels.
Roadside emergencies JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Batteries contain sulfuric acid which can burn skin, eyes, and clothing, if contacted. Do not attempt to push-start your vehicle. Automatic transmissions do not have push-start capability; also, the catalytic conveter may become damaged.
Roadside emergencies Connecting the jumper cables + + – – 1. Connect the positive (+) booster cable to the positive (+) terminal of the discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. + + – – 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery.
Roadside emergencies + + – – 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery. + + – – 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’s engine, away from the battery and the carburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped.
Roadside emergencies Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables. Removing the jumper cables + + – – Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface.
Roadside emergencies + + – – 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. + + – – 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
Roadside emergencies WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or, if you are a member, your roadside assistance center. It is recommended that your vehicle be towed by wheel lift or flatbed equipment. However, a slingbelt with T-hooks can also be used. If your vehicle is equipped with an air dam and must be towed from the front, it is recommended that your vehicle be towed by wheel lift or flatbed equipment to prevent damage to the air dam.
Customer assistance GETTING THE SERVICES YOU NEED At home Ford Motor Company and Ford of Canada have authorized dealerships to service your vehicle. It is preferred that you return to the Ford dealer where your vehicle was purchased when warranty repairs are needed. However, you may also take your vehicle to another Ford Motor Company or Ford of Canada dealership authorized for warranty repairs.
Customer assistance In Canada: Customer Relationship Centre Ford Motor Company of Canada, Limited P.O. Box 2000 Oakville, Ontario L6J 5E4 1-800-565-3673 (FORD) If you own a Lincoln vehicle and are away from home when your vehicle needs service, or if you need more help than the dealership could provide, after following the steps described above, contact the Ford Customer Relationship Center to find an authorized dealership to help you.
Customer assistance In some states (in the U.S.) you must directly notify Ford in writing before pursuing remedies under your state’s warranty laws. Ford is also allowed a final repair attempt in some states. In the United States, a warranty dispute must be submitted to the Dispute Settlement Board before taking action under the Magnuson-Moss Warranty Act, or to the extent allowed by state law, before pursuing replacement or repurchase remedies provided by certain state laws.
Customer assistance THE DISPUTE SETTLEMENT BOARD (U.S. ONLY) The Dispute Settlement Board is: • an independent, third-party arbitration program for warranty disputes • available free to owners and lessees of qualifying Ford Motor Company vehicles The Dispute Settlement Board may not be available in all states. Ford Motor Company reserves the right to change eligibility limitations, modify procedures and/or to discontinue this service without notice and without incurring obligations per applicable state law.
Customer assistance Board membership The Board consists of: • three consumer representatives • a Ford or Lincoln Mercury dealership representative Consumer candidates for Board membership are recruited and trained by an independent consulting firm. The dealership Board member is chosen from Ford and Lincoln Mercury dealership management, recognized for their business leadership qualities.
Customer assistance You will receive a letter of explanation if your application does not qualify for Board review. Oral presentations If you would like to make an oral presentation, indicate YES to question 6 on the application. While it is your right to make an oral presentation before the Board, this is not a requirement and the Board will decide the case whether or not an oral presentation is made. An oral presentation may be requested by the Board as well.
Customer assistance UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) In those cases where you continue to feel that the efforts by Ford and the dealer to resolve a factory-related vehicle service concern have been unsatisfactory, Ford of Canada participates in an impartial third party mediation/arbitration program administered by the Canadian Motor Vehicle Arbitration Plan (CAMVAP).
Customer assistance If your vehicle must be serviced while you are traveling or living in Central or South America, the Caribbean, or the Middle East, contact the nearest Ford dealership. If the dealership cannot help you, write or call: FORD MOTOR COMPANY WORLDWIDE DIRECT MARKET OPERATIONS 1555 Fairlane Drive Fairlane Business Park #3 Allen Park, Michigan 48101 U.S.A. Telephone: (313) 594-4857 FAX: (313) 390-0804 If you are in another foreign country, contact the nearest Ford dealership.
Customer assistance Obtaining a French owner’s guide French Owner’s Guides can be obtained from your dealer or by writing to Ford Motor Company of Canada, Limited, Service Publications, P.O. Box 1580, Station B, Mississauga, Ontario L4Y 4G3. IN CALIFORNIA (U.S. ONLY) California Civil Code Section 1793.
Customer assistance REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect which could cause a crash, or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Cleaning WASHING THE EXTERIOR OF YOUR VEHICLE Never wash a vehicle that is “hot to the touch” or during exposure to strong, direct sunlight. It is recommended that you wash your vehicle regularly with cool or lukewarm water and a neutral Ph shampoo, such as Detail Wash (ZC-3–A), which is available from your authorized Ford, Lincoln or Mercury dealer. Always use a clean sponge or carwash mitt with plenty of water for best results.
Cleaning Do not allow paint sealant to come in contact with any non-body (low-gloss black) colored trim, such as grained door handles, roof racks, bumpers, side moldings, mirror housings or the windshield cowl area. The paint sealant will “gray” or stain the parts over time. REPAIRING PAINT CHIPS Remove particles such as bird droppings, tree sap, insect deposits, tar spots, road salt and industrial fallout before repairing paint chips.
Cleaning CLEANING THE ENGINE Engines are more efficient when they are clean because grease and dirt buildup keep the engine warmer than normal. When washing: • The engine must be cool to the touch before spraying with water. • Never spray a hot engine with cold water, as damage to the engine block or engine components may occur. • Use caution when using a self-serve power washer (1000psi maximum pressure) to clean the engine, as the high-pressure fluid could penetrate the sealed parts and cause damage.
Cleaning WASHING NON-PAINTED PLASTIC EXTERIOR PARTS Use Detail Wash (ZC-3–A) for routine cleaning. If tar or grease spots are present, clean with Extra Strength Tar and Road Oil Removal (B7A-19520–AA). Use only approved products to clean plastic parts. These products are available from your authorized Ford, Lincoln or Mercury dealer. WASHING THE EXTERIOR LAMPS In order to avoid scratching the plastic lamps, do not use dry paper towels, non-approved chemical solvents or abrasive cleaners.
Cleaning CLEANING THE INSTRUMENT PANEL Clean the instrument panel with a damp cloth, then dry with a dry cloth. Avoid cleaners or polish that increase the gloss of the upper portion of the instrument panel. The dull finish in this area helps protect the driver from undesirable windshield reflection. Do not use chemical solvents or strong detergents when cleaning the steering wheel or instrument panel to avoid contamination of the air bag system.
Cleaning Do not use household cleaning products, alcohol solutions, solvents or cleaners intended for rubber, vinyl and plastics, or oil/petroleum-based leather conditioners. These products may cause premature wearing of the clear, protective coating. CLEANING THE INSIDE WINDOWS Use Ultra Clear Spray Glass Cleaner (E4AZ-19C507–AA) for the inside windows if they become fogged. To clean, use two lint-free, soft towels, folded into a pad-shape.
Cleaning Ford Extra Strength Tar and Road Oil Remover* (not available in Canada) Ford Extra Strength Upholstery Cleaner (not available in Canada) Ford Custom Bright Metal Cleaner Motorcraft Premium Car Wash Concentrate Motorcraft Carlite Glass Cleaner (Canada only) Ford Spot and Stain Remover* Ford Super Premium Tire and Trim Dressing Ford Triple Clean Ford Ultra-Clear Spray Glass Cleaner (not available in Canada) Ford Engine Shampoo and Degreaser * May be sold with the Motorcraft name 213
Maintenance and specifications SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easy location. • We provide a scheduled maintenance guide which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide the necessary parts and service. Check your Warranty Guide to find out which parts and services are covered.
Maintenance and specifications Note: Do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom left corner of the instrument panel. HOOD 2. Go to the front of the vehicle and release the auxiliary latch that is located in the center top of the grill. 3. Lift the hood and secure it with the prop rod.
Maintenance and specifications IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT Engine compartment component locations Refer to the 7.3 Liter Power Stroke Direct Injection Turbo Diesel Owner’s Guide Supplement for diesel engine component locations. 1 2 3 4 5 6 10 1. Windshield washer fluid reservoir 2. Engine oil filler cap (except 4.2L V6 engine) 3. Automatic transmission fluid dipstick 4. Air filter assembly 5. Engine oil dipstick 6. Engine oil filler cap (4.2L V6 engine only) 7.
Maintenance and specifications WINDSHIELD WASHER FLUID Washer fluid Check the washer fluid whenever you stop for fuel. The reservoir is symbol. highlighted with a If the level is low, add enough fluid to fill the reservoir. In very cold weather, do not fill the reservoir all the way. Only use a washer fluid that meets Ford specification ESR-M17P5–A. Refer to Lubricant specifications in this chapter.
Maintenance and specifications 5. Locate and carefully remove the engine oil level indicator (dipstick). 6. Wipe the indicator clean. Insert the indicator fully, then remove it again. • If the oil level is between the MIN and MAX marks, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below the MIN mark, add enough oil to raise the level within the MIN-MAX range. • Oil levels above the MAX mark may cause engine damage. Some oil must be removed from the engine by a service technician. 7.
Maintenance and specifications Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2. If the engine oil level is not within the normal range, add only certified engine oil of the recommended viscosity. Remove the engine oil filler cap and use a funnel to pour the engine oil into the opening. 3. Recheck the engine oil level. Make sure the oil level is not above the MAX mark on the engine oil level indicator (dipstick). 4.
Maintenance and specifications Ford production and aftermarket (Motorcraft) oil filters are designed for added engine protection and long life. If a replacement oil filter is used that does not meet Ford material and design specifications, start-up engine noises or knock may be experienced. It is recommended you use the appropriate Motorcraft oil filter (or another brand meeting Ford specifications) for your engine application.
Maintenance and specifications When the battery is disconnected or a new battery installed, the transmission must learn its adaptive strategy. As a result of this, the transmission may shift firmly. This operation is considered normal and will fully update transmission operation to its optimum shift feel. Batteries normally produce explosive gases which can cause personal injury. Therefore, do not allow flames, sparks or lighted substances to come near the battery.
Maintenance and specifications RN LE TU AD RE 4. Allow the engine to idle for at least one minute. 5. Turn the A/C on and allow the engine to idle for at least one minute. 6. With your foot on the brake pedal and with the A/C on, put the vehicle in D (Drive) and allow the engine to idle for at least one minute. 7. Drive the vehicle to complete the relearning process. • The vehicle may need to be driven 16 km (10 miles) or more to relearn the idle and fuel trim strategy.
Maintenance and specifications The auxiliary battery is located on the passenger side frame rail. Gasoline engines Disconnect: 1. Disconnect the primary battery ground cable. 2. Disconnect the auxiliary battery frame ground. • Remove the ground bolt. • Pull the cable away from the frame and make sure that the cable does not contact the frame.
Maintenance and specifications Connect: 1. Reconnect the auxiliary battery frame ground. 2. Reconnect the primary battery ground cable. Diesel engines Disconnect: Secondary positive cable remains energized after disconnection. Make sure the tool does not contact any ground surface. 1. Disconnect the secondary positive cable from the primary battery terminal.
Maintenance and specifications 2. Wrap the secondary positive cable with a non-conductive material to insulate. 3. Disconnect the primary battery ground cable. 4. Disconnect the primary battery positive cable. Connect: Secondary positive cable remains energized after disconnection. make sure the tool does not contact any ground surface. 1. Reconnect the primary battery positive cable. 2. Reconnect the primary battery ground cable.
Maintenance and specifications 3. Unwrap the secondary positive cable and reconnect to the primary battery terminal. ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant should be checked at the mileage intervals listed in the scheduled maintenance guide. The coolant concentration should be maintained at 50/50 coolant and water, which equates to a freeze point of -36° C (-34° F).
Maintenance and specifications When the engine is cold, check the level of the engine coolant in the reservoir. COLD FILL LEVEL • The engine coolant should be at the “cold fill level” or within the “cold fill range” as listed on the engine coolant reservoir (depending upon application). • Refer to the Scheduled Maintenance Guide for service interval schedules. • Be sure to read and understand Precautions when servicing your vehicle in this chapter.
Maintenance and specifications Do not add engine coolant when the engine is hot. Steam and scalding liquids released from a hot cooling system can burn you badly. Also, you can be burned if you spill coolant on hot engine parts. Do not put engine coolant in the windshield washer fluid container. If sprayed on the windshield, engine coolant could make it difficult to see through the windshield.
Maintenance and specifications • Do not mix with recycled coolant unless from a Ford-approved recycling process (see Use of Recycled Engine Coolant section). For vehicles with overflow coolant systems with a non-pressurized cap on the coolant recovery system, add coolant to the coolant recovery reservoir when the engine is cool. Add the proper mixture of coolant and water to the “cold full” level.
Maintenance and specifications If you have to add more than 1.0 liter (1.0 quart) of engine coolant per month, have your dealer check the engine cooling system. Your cooling system may have a leak. Operating an engine with a low level of coolant can result in engine overheating and possible engine damage.
Maintenance and specifications If you drive in extremely hot climates: • It is still necessary to maintain the coolant concentration above 40%. • NEVER decrease the coolant concentration below 40%. • Decreased engine coolant concentrations below 40% will decrease the corrosion protection characteristics of the engine coolant and may cause engine damage. • Decreased engine coolant concentrations below 40% will decrease the freeze protection characteristics of the engine coolant and may cause engine damage.
Maintenance and specifications When this occurs the vehicle will still operate. However: • The engine power will be limited. • The air conditioning system will be disabled. Continued operation will increase the engine temperature and the engine will completely shut down, causing steering and braking effort to increase. Once the engine temperature cools, the engine can be re-started. Take your vehicle to a service facility as soon as possible to minimize engine damage.
Maintenance and specifications WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire. The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap. Otherwise, fuel may spray out and injure you or others.
Maintenance and specifications Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before fueling your vehicle. • Always turn off the vehicle before fueling. • Automotive fuels can be harmful or fatal if swallowed. Fuel such as gasoline is highly toxic and if swallowed can cause death or permanent injury. If fuel is swallowed, call a physician immediately, even if no symptoms are immediately apparent.
Maintenance and specifications The flow of fuel through a fuel pump nozzle can produce static electricity, which can cause a fire if fuel is pumped into an ungrounded fuel container. Use the following guidelines to avoid static build-up when filling an ungrounded fuel container: • Place approved fuel container on the ground. • DO NOT fill a fuel container while it is in the vehicle (including the cargo area). • Keep the fuel pump nozzle in contact with the fuel container while filling.
Maintenance and specifications The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap. Otherwise, fuel may spray out and injure you or others. If you do not use the proper fuel filler cap, excessive pressure or vacuum in the fuel tank may damage the fuel system or cause the fuel cap to disengage in a collision, which may result in possible personal injury.
Maintenance and specifications Fuel quality If you are experiencing starting, rough idle or hesitation driveability problems during a cold start, try a different brand of “Regular” unleaded gasoline. “Premium” unleaded gasoline is not recommended (particularly in the United States) because it may cause these problems to become more pronounced. If the problems persist, see your dealer or a qualified service technician.
Maintenance and specifications Fuel Filter For fuel filter replacement, see your dealer or a qualified service technician. Refer to the scheduled maintenance guide for the appropriate intervals for changing the fuel filter. Replace the fuel filter with an authorized Motorcraft part. The customer warranty may be void for any damage to the fuel system if an authorized Motorcraft fuel filter is not used.
Maintenance and specifications • • • • Allow no more than 2 automatic click-offs when filling. Always use fuel with the recommended octane rating. Use a known quality gasoline, preferably a national brand. Use the same side of the same pump and have the vehicle facing the same direction each time you fill up. • Have the vehicle loading and distribution the same every time. Your results will be most accurate if your filling method is consistent. Calculating fuel economy 1.
Maintenance and specifications • Idling for long periods of time (greater than one minute) may waste fuel. • Anticipate stopping; slowing down may eliminate the need to stop. • Sudden or hard accelerations may reduce fuel economy. • Slow down gradually. • Driving at reasonable speeds (traveling at 88 km/h [55 mph] uses 15% less fuel than traveling at 105 km/h [65 mph]). • Revving the engine before turning it off may reduce fuel economy. • Using the air conditioner or defroster may reduce fuel economy.
Maintenance and specifications • Adding certain accessories to your vehicle (for example bug deflectors, rollbars/light bars, running boards, ski/luggage racks) may reduce fuel economy. • Using fuel blended with alcohol may lower fuel economy. • Fuel economy may decrease with lower temperatures during the first 12–16 km (8–10 miles) of driving. • Driving on flat terrain offers improved fuel economy as compared to driving on hilly terrain.
Maintenance and specifications If other than Ford, Motorcraft or Ford-authorized parts are used for maintenance replacements or for service of components affecting emission control, such non-Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability. Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire.
Maintenance and specifications • Next, at least 20 minutes driving in stop-and-go, city-type traffic with at least four idle periods. Allow the vehicle to sit for at least eight hours without starting the engine. Then, start the engine and complete the above driving cycle. The engine must warm up to its normal operating temperature. Once started, do not turn off the engine until the above driving cycle is complete. FULL COLD CHECKING AND ADDING POWER STEERING FLUID Check the power steering fluid.
Maintenance and specifications For E-SuperDuty vehicles with the Hydro-Boost Brake System, do not press the brake pedal after the engine has been turned off. 5. Recheck the fluid level on the dipstick. Do not add fluid if the level is between the arrows in the FULL COLD range. 6. If the fluid is low, add fluid in small amounts, continuously checking the level until it reaches the FULL COLD range. Be sure to put the dipstick back in the reservoir.
Maintenance and specifications If you use a brake fluid that is not DOT 3, you will cause permanent damage to your brakes. Do not let the reservoir for the master cylinder run dry. This may cause the brakes to fail. DRIVELINE UNIVERSAL JOINT AND SLIP YOKE Your vehicle may be equipped with universal joints that require lubrication. Refer to the scheduled maintenance guide for maintenance intervals.
Maintenance and specifications 6. Install the dipstick making sure it is fully seated in the filler tube. 7. Remove the dipstick and inspect the fluid level. The fluid should be in the designated area for normal operating temperature or ambient temperature. Low fluid level Do not drive the vehicle if the fluid level is at the bottom of the dipstick and the ambient temperature is above 10°C (50°F).
Maintenance and specifications Adjusting automatic transmission fluid levels Before adding any fluid, make sure the correct type is used. The type of fluid used is normally indicated on the dipstick and also in the Lubricant specifications section in this chapter. Use of a non-approved automatic transmission fluid may cause internal transmission component damage. If necessary, add fluid in 250 ml (1/2 pint) increments through the filler tube until the level is correct.
Maintenance and specifications 3. Carefully separate the two halves of the air filter housing. 4. Remove the air filter element from the housing. 5. Install a new air filter element. Be careful not to crimp the filter element edges between the air filter housing. This could cause filter damage and allow unfiltered air to enter the engine if not properly seated. 6. Replace the two halves of the air filter housing and secure the clamp. 7. Connect the fresh air inlet tube to the radiator support.
Maintenance and specifications Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 1/2) times as well on the government course as a tire graded 100.
Maintenance and specifications SERVICING YOUR TIRES Checking the tire pressure • Use an accurate tire pressure gauge. • Check the tire pressure when tires are cold, after the vehicle has been parked for at least one hour or has been driven less than 5 km (3 miles). • Adjust tire pressure to recommended specifications found on the Certification Label. Tire pressure information can also be found on the Tire Information label located on the inside of the fuel filler door.
Maintenance and specifications • Five tire rotation Replacing the tires Replace the tires when the wear band is visible through the tire treads. When replacing full size tires, never mix radial bias-belted, or bias-type tires. Use only the tire sizes that are listed on the Certification Label. Make sure that all tires are the same size, speed rating, and load-carrying capacity. Use only the tire combinations recommended on the label.
Maintenance and specifications Do not replace your tires with “high performance” tires or larger size tires. Failure to follow these precautions may adversely affect the handling of the vehicle and make it easier for the driver to lose control and roll over. Tires that are larger or smaller than your vehicle’s original tires may also affect the accuracy of your speedometer. SNOW TIRES AND CHAINS Snow tires must be the same size and grade as the tires you currently have on your vehicle.
Maintenance and specifications MOTORCRAFT PART NUMBERS Component1 4.2L V6 engine Air filter FA-1634 element Battery BXT-65-750 (standard) Battery BH-65DC (auxiliary) Fuel filter FG-872 Oil filter FL-400-S PCV valve EV-251 Spark plugs2 AGSF-34EEM3 4.6L V8 engine FA-1634 5.4L V8 engine FA-1634 6.8L V10 engine FA-1634 BXT-65-750 BXT-65-750 BXT-65-750 BH-65DC BH-65DC BH-65DC FG-872 FL-820-S EV-233 AWSF-32PP4 FG-872 FL-820-S EV-233 AGSF-22W FG-872 FL-820-S EV-233 AGSF-22W 1 Refer to the 7.
Maintenance and specifications REFILL CAPACITIES Fluid Ford Part Application Capacity Name Brake fluid Motorcraft High All Fill to line on Performance reservoir DOT 3 Motor Vehicle Brake Fluid Engine Motorcraft SAE All 5.7L (6.0 oil-gasoline 5W-20 Super quarts) engine (includes Premium Motor filter change) Oil Engine oil-diesel Refer to the 7.3L Power Stroke Direct Injection engine (includes Turbo Diesel Owner’s Guide Supplement. filter change) Motorcraft 4.2L V6 engine 22.0L (23.
Maintenance and specifications Fluid Engine coolant-diesel engine Power steering fluid Rear axle4 Ford Part Application Capacity Name Refer to the 7.3L Power Stroke Direct Injection Turbo Diesel Owner’s Guide Supplement. 1 Motorcraft MERCON威 ATF All Keep in FULL range on dispstick 2.6-2.7L (5.5-5.8 pints) 2 Motorcraft SAE 75W-140 Synthetic rear axle lubricant Motorcraft 80W-90 Premium rear axle lubricant Visteon 8.8/9.75 inch conventional and Traction-Lok Dana 9.75 inch 3.0L (6.
Maintenance and specifications Fluid Fuel tank Transmission fluid 6 Windshield washer fluid 1 Ford Part Name N/A Application Capacity All regular and extended length vans and wagons 138 inch wheelbase (except E-Super Duty) 158 inch wheelbase (except E-Super Duty) 176 inch wheelbase (except E-Super Duty) 158 inch and 176 inch wheelbase (E-Super Duty) Automatic (4R70W) 132.4L (35.
Maintenance and specifications 2 If your vehicle’s rear axle is filled with a synthetic rear axle lubricant it is considered lubricated for life. These lubricants do not need to be checked or changed unless a leak is suspected, service is required or the axle assembly has been submerged in water. The axle lubricant should be changed any time the rear axle has been submerged in water. Fill 6 mm to 14 mm (1/4 inch to 9/16 inch) below bottom of fill hole. Add 118 ml (4 oz.
Maintenance and specifications LUBRICANT SPECIFICATIONS Item Brake fluid Door weatherstrips Ford part name Motorcraft High Performance DOT 3 Motor Vehicle Brake Fluid Silicone Lubricant Ford part number PM-1 Ford specification ESA-M6C25-A and DOT 3 F7AZ-19G208-BA ESR-M13P4-A and F5AZ-19553-AA ESE-M97B44-A Engine coolant Motorcraft VC-4–A (in Premium Engine Canada, Coolant Motorcraft (green-colored) CXC-10) Motorcraft VC-7–A WSS -M97B51-A1 Premium Gold Engine Coolant (yellow-colored) WSS-M2C153-H Engine
Maintenance and specifications Item Automatic transmission (4R100) 1 Automatic tranmission (4R70W) 1 Disc brake caliper rails Ford part name Motorcraft MERCON威 ATF Motorcraft MERCON威V ATF Motorcraft Silicone Brake Caliper Grease and Dielectric Compound Parking brake Motorcraft assembly MERCON威 (E-Super Duty) Automatic Transmission Fluid Motorcraft SAE Visteon conventional and 75W-140 High Performance Traction-Lok axles (E-150) 2 Synthetic Rear Axle Lubricant Dana 9.75 inch Motorcraft SAE (M60–1U) 10.
Maintenance and specifications correct type. Refer to your scheduled maintenance guide to determine the correct service interval. Some transmission fluids may be labeled as dual usage, such as MERCON威 and MERCON威 V. These dual usage fluids are not to be used in an automatic transmission that requires use of the MERCON威 type fluid. However, these dual usage fluids may be used in transmissions that require the MERCON威 V type fluid. MERCON威 and MERCON威 V type fluids are not interchangeable.
Maintenance and specifications VEHICLE DIMENSIONS Van/wagon models E-150 E-250 E-350 2 055 mm (80.9 2 118 mm (83.4 2 136 mm in) in) (84.1 in) 1 763 mm (69.4 in)/ 1 702 mm (67.0 in) 2 014 mm (79.3 in) (1) Overall height (2) Track front/rear (3) Overall width (excluding mirrors) (4) Wheelbase 3 505 mm (138 in) (5) Overall length Regular van, 5 382 mm (211.9 in) Extended, 5 890 mm (231.
Maintenance and specifications 4 5 Cutaway/commercial stripped chassis models (1) Overall height (2) Track front/rear (3) Overall width (excluding mirrors) 262 E-250 E-350 E-Super Duty Refer to Body Builder for specifications 1 763 mm (69.4 in)/ 1 689 mm (66.5 in) 1 763 mm 1 763 mm (69.4 in)/ (69.4 in)/ SRW 1689 mm 1 973 mm (66.5 in), (77.7 in) DRW 1 859 mm (73.2 in) Refer to Body Builder for specifications.
Maintenance and specifications (4) Wheelbase (5) Overall length E-250 3 149.6 mm (124 in) E-350 E-Super Duty 3 505 mm 4 013 mm (138 in) (158 in) 4 013 mm 4 470 mm (158 in) (176 in) 4 470 mm (176 in) Refer to Body Builder for specifications. VEHICLE IDENTIFICATION NUMBER Complete Ford built vehicles The vehicle identification number is attached to your vehicle in the following places: • On the metal tag attached to the top of the instrument panel on the driver’s side. • On the certification label.
Accessories FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of genuine Ford accessories are available for your vehicle through your local authorized Ford, Lincoln, Mercury or Ford of Canada dealer. These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and aerodynamic appearance of your vehicle.
Accessories Console (Engine cover) Daytime running lights (DRL) First aid and highway kits Fog lights Hitch mount bicycle carrier Inside mirror, electrochromic with compass (with and without temperature display) Removable roof rack Running boards — Aluminum Speed control Trailer hitch (Class III) Trailer hitch bars and balls Trailer hitch wiring adaptor Trailgate table Protection and appearance equipment Air bag anti-theft locks Battery warmer Carpet floor mats Cleaners, waxes and polishes Door edge guards
Accessories For maximum vehicle performance, keep the following information in mind when adding accessories or equipment to your vehicle: • When adding accessories, equipment, passengers and luggage to your vehicle, do not exceed the total weight capacity of the vehicle or of the front or rear axle (GVWR or GAWR as indicated on the Safety compliance certification label). Consult your dealer for specific weight information.
Index A Air bag supplemental restraint system ........................................132 and child safety seats ............134 description ..............................132 disposal ....................................137 driver air bag ..........................135 indicator light ...................14, 136 operation .................................135 passenger air bag ...................135 Air cleaner filter ...............247, 253 Air conditioning manual heating and air conditioning system .........
Index waxing .....................................207 wheels ......................................208 windows ..................................212 wiper blades ............................210 Clock ..........................23, 28, 37, 45 Compass, electronic ..................104 calibration ...............................106 set zone adjustment ...............105 Console overhead ..........................102–103 Controls power seat ...............................114 Coolant checking and adding .........
Index recommendations ...................219 refill capacities ........................254 specifications ..................258, 260 Exhaust fumes ..........................151 F Fail safe cooling ........................231 Fluid capacities .........................254 Four-Wheel Drive vehicles preparing to drive your vehicle .....................................156 Fuel ............................................233 calculating fuel economy .......238 cap ...........................................
Index heating and air conditioning system .......................................79 Hood ..........................................215 I Ignition .......................148, 260–261 Infant seats (see Safety seats) .....................139 Inspection/maintenance (I/M) testing ........................................242 Instrument panel cleaning ...................................211 cluster ................................12, 211 lighting up panel and interior .......................................
Index Radio ............................................20 Relays ................................177, 184 Remote entry system .......109–110 illuminated entry ....................112 locking/unlocking doors ................................108–110 panic alarm .............................110 replacement/additional transmitters .............................111 replacing the batteries ...........110 extension assembly ................131 for adults .........................122–124 for children .............
Index snow tires and chains ............252 tire grades ...............................249 treadwear ................................249 Towing .......................................163 recreational towing .................172 trailer towing ..........................163 wrecker ....................................196 Traction-lok rear axle ...............155 Transmission .............................156 fluid, checking and adding (automatic) .............................245 fluid, refill capacities ......