ForceDecks Instruction Manual for FDMax, FDLite (v.2), and FDMIni Version 1.
Contents 1 Important Notice ........................................................................................................ 3 1.1 F.C.C. Notification........................................................................................................................ 3 2 Introduction ................................................................................................................ 4 3 Welcome to ForceDecks .......................................................................
1 Important Notice 1.1 F.C.C. Notification Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
2 Introduction This document provides information about the installation and use of the FDMax, FDLIte (v.2), and FDMini ForceDecks systems, including the assembly of hardware and installation of software. 3 Welcome to ForceDecks ForceDecks are a dual force plate and auto-analysis system, used to analyse an individual’s balance, strength and movement strategies in a range of exercises and jumps. The collection of ForceDecks data is about measuring different muscle characteristics, in controlled situations.
4 Getting Started: ForceDecks Hardware ForceDecks consists of a pair of connected uni-axial force plates. This means they produce vertical force data only. Each force plate is loaded with four highly sensitive strain gauge sensors. When an individual is in contact with the plates, the sensors will detect movement within the strain gauge, and the strain gauge will compress in proportion to the amount of force applied.
4.2 ForceDecks Setup ForceDecks plates can be mounted on: • • • Steel bases; Set into weightlifting platforms; or Used freestanding on any flat, hard surface. 4.3 Floor Considerations ForceDecks are designed to be mobile, however it is important ForceDecks are mounted on a surface that is: • • As rigid as possible; and As flat as possible. For example, concrete floors are ideal, whereas sprung floors are not suitable.
Note: It is advised to follow the below configuration to prevent having to adjust left and right plate settings in the ForceDecks software. The ForceDecks system consists of a ‘Primary’ plate and a ‘Secondary’ plate. It is important to ensure cables between the plates and power source are routed to prevent them being stepped on or caught underneath the plate, as this can cause instability, potentially affect measurements and/or damage the cables. 4.
Note: ForceDecks will be partially charged when shipped to clients, enabling them to use the ForceDecks straight out of the box. 4.6.1 Charging ForceDecks There are two ways to charge ForceDecks batteries, using the supplied USB cable. The ForceDecks batteries will charge when: 1. Plugged into a USB port on a computer, or 2. Plugged into the mains power with a USB wall adapter (mains power). • Do not charge a device if your Mini-USB cable or wall adapter are damaged.
Note: When turning on the ForceDecks, if the power button is pressed on the Secondary plate, the plate will turn on then straight off again. 5 Getting Started: ForceDecks Software ForceDecks software is the heart of the ForceDecks system, taking previously laborious tasks and performing them automatically to facilitate rapid testing of individuals in time-pressured environments.
5.1 Setup Your Software To setup your software, scan the QR code or Or visit our website to access the ForceDecks Starter’s Guide: https://support.vald.com/hc/en-au/articles/4999028480025 5.2 Minimum Device Requirements The following specifications are recommended for any device running ForceDecks Windows software: Windows Operating System Windows 7 x 64 or later Processor Intel i5 / i7 / i9 Ram 8 GB or greater Storage 500 MB minimum for install Ports 1 x USB 2.0 / USB 3.
5.3 Bluetooth Connection ForceDecks plates (FDMini, LDLite (V2), FDMax) can be connected to a laptop via Bluetooth. Note: To enable Bluetooth connectivity the latest ForceDecks Firmware must be installed, and only one set of ForceDecks plates turned on. To connect ForceDecks plates to a laptop or iOS device via Bluetooth: 0. 1. 2. 3. 4. 5. 6.