Installation Instructions

ManualsBrandsFolger Adam ManualsElectronicsFail Secure Fire Rated Electric Strike in Satin Stainless Steel

Folger Adam 700 Series Electric Strike

HES, Inc.

22630 N. 17th Ave.

Phoenix, AZ 85027

800-626-7590

www.hesinnovations.com

Product Components

Electrical Specifications

ELECTRICAL RATINGS FOR SOLENOID

MINIMUM WIRE GAUGE REQUIREMENTS

SOLENOID VOLTAGE

CONTINUOUS DUTY

12VDC

.29

24VDC

160

.15

Resistance in Ohms

Amps

Solenoids are rated at +/- 10% indicated value.

200 feet or less

200 - 300 feet

300 - 400 feet

18 gauge

16 gauge

14 gauge

18 gauge

16 gauge

#12 x 2 1/2” Wood Faceplate Mounting Screws

Plug In Connector

Electric Strike Body & Faceplate

#12-24 Faceplate Mounting Screws

#8-32 Body Mounting Screws

#6-32 x 3/16” Keeper Shim Screws (742-75 only)

Deadlatch Tabs (742-75 only)

#6-32 x 5/16” Deadlatch Tabs Screws (742-75 only)

Keeper Shim (742-75 only)

Summary of content (6 pages)

PAGE 1
HES, Inc. 22630 N. 17th Ave. Phoenix, AZ 85027 800-626-7590 www.hesinnovations.
PAGE 2
Installation Directions 2 CAUTION! Before connecting any device at the installation site, verify input voltage using a multimeter. Many power supplies and low voltage transformers operate at higher levels than listed. Any input voltage exceeding 10% of the solenoid rating may cause severe damage to the unit and will void the warranty. Prepare Strike Prepare Frame 1. Attach the faceplate to the strike body using the #8-32 Body Mounting screws as illustrated on page 3, Diagram 2. 2.
PAGE 3
Installation Directions 3 Diagram 2: Faceplate Attachment To install the 700 series electric strike body to the faceplate, install two #8-32 Body Mounting screws as shown. Make sure bolts are tightened and secured. Keeper position can be adjusted by loosening the #8-32 body mounting screws, and repositioning the strike body as needed. Retighten body mounting screws after adjustment is made Diagram 3: Determining Mortise Offset 4” [101.60] B CL Mortise Door Prep 8” [203.
PAGE 4
Cutout Templates 4 Inches [mm] 712 Template & Dimensions (RHRB APPLICATION SHOWN) Method of install may vary per door & frame manufacturer 1-1/4” [31.75] 5/8” [15.88] 1-5/8” [41.3] 4-7/8" [123.83] 4-1/8" [104.78] 3-3/8" [85.72] 4-7/8” [123.83] 3-3/8” [85.72] 6” [152.4] 4-1/8” [104.78] 1/2” [13] 1/8” [3.5] 1-1/4” [31.75] 1-1/2” [38.10] 1-1/2" [38.10] 712-75 Template & Dimensions (RHRB APPLICATION SHOWN) Method of install may vary per door & frame manufacturer 1-1/4” [31.75] 5/8” [15.
PAGE 5
Cutout Templates 5 Inches [mm] 732 Template & Dimensions (RHRB APPLICATION SHOWN) Method of install may vary per door & frame manufacturer 1-1/4” [31.75] 5/8” [15.88] 4-7/8” [123.83] 3-3/8” [85.72] 4-7/8" [123.83] 4-1/8” [104.78] 1/2” [12.70] 1-1/4” [31.75] 4-1/8" [104.78] 1-5/8” [41.3] 3-3/8" [85.72] 1-1/2” [38.10] Drill 1" Dia. Hole thru, for wires & solenoid. 1-5/16” [26.34] CL CL 31/32” [24.5] 3/4” [19.05] 1-1/2" [38.10] 1/8” [3.5] 3-5/8” [92.
PAGE 6
Frame Preparation 6 Inches [mm] 742-75 4500 WITH Dimensions SCHLAGE ANDand YALETemplate MORTISE LOCKS (RHRB APPLICATION SHOWN) Method of install may vary per door & frame manufacturer 1-1/4” [31.75] 5/8” [15.88] 3/4" [18.8] 4-7/8" [123.83] 4-1/8" [104.78] 3-3/8" [85.72] 4-7/8" [123.4] Ø 3/4" [19.1] 3/8" [9.3] 3-3/8" [85.7] 9/16" [14.8] 4-1/8" [104.8] 1/8" [3.2] 6-5/16" [159.9] 5/8" [15.9] 1-1/4" [31.5] 1-15/16" [49] 1-1/2" [38.1] 1-1/2" [38.