Front occurring 1.2 Part names 1.2.1 Front camera (main unit) front view Voice recording button Press to enable or disable voice recording. GPS LED Indicates the GPS connection status. Manual recording button Press to start manual recording. Format button Press and hold to format the memory card. Recording LED Indicates the recording status. Y-IN Input port Used to connect the rear camera (optional). WIFI LED Indicates the WI-Fi D-IN power port connection status. Used to connect the power cable.
Proud survive 1.2.2 Front camera (main unit) rear view Microphone Used for voice recording. Memory card slot Insert a memory card to save recordings. | Reset button = Insert the tip of a sharp object to (8 5 reset the product when an error occur S. Security LED -Indicates that video is being recorded. Front camera lens Mount connector Records the front view. Used to connect the mount. 1.2.3 Rear camera (optional) Adhesive mount Used to fix the rear camera in the vehicle.
Product stridden 1.3 Removing and inserting the memory card Follow the instructions to remove the memory card from the product or to insert the memory card into the product. Homemaking the memory card Ensure that the product is turned off, and then gently push the bottom of the memory card with your fingernail. The lower part of the memory card will be exposed. Remove it from the product.
2. Installing the product 2.1 Installing the front camera (main unit) Follow the instructions to properly install the product. 2.1.1 Selecting an installation location Select an installation location that can record the entire view in front of the vehicle without obstructing the driver's vision. Ensure that the front camera lens is located in the center of the windshield.
staffing the product Remove the protective film from the adhesive mount, and then press the mount to the installation location. Remove the product from the mount and push the mount against the windshield to ensure that the mount is firmly fixed. 5 po Align the product to the mount, and then slide it into Tp . the locking position until you hear a click. ยป The product may fall and he damaged during vehicle operation if it Is not firmly fixed to the mount.
Enshrining dip product 2.1.3 Connecting the power cable When the engine and electrical accessories are turned off, connect the car charger. The herd wiring cable (optional) must be professionally installed to the vehicle hy o trained mechanic. Connect the car charger to the product's DC-IN power port and insert the cigar jack into the vehicle's power socket. te The In cation and specifications of the power socket may differ by vehicle make and model. = Use the authentic THINK WARE car charger.
staffing the product 2.2 Installing the rear camera (optional) Refer to the following instructions to properly install the rear camera. 2.2.1 Selecting an installation location Select a location on the rear windshield where there is na defrost grid wire and the camera can record the entire rear view. = For vehicles with a sunshade attached to the rear windshield, vou must select a location where using the sunshade will not interfere with camera operation.
Enshrining dip product 2.2.2 Securing the rear camera Refer to the following instructions to secure the product to the installation location. 1 After determining the installation location, wipe the installation surface of the windshield with a dry cloth. ia Check the installation location before you secure the rear camera to the rear windshield. After a securing the rear camera to the windshield, iris hard to remove the camera or change the installation location dus to the strong adhesive.
staffing the product 2.2.3 Connecting the rear camera cable Power off the product and connect the rear camera cable to the front camera (main unit). 1 Connect one end of the rear camera cable to the front camera's V-IN port. 2 Connect the either end of the rear camera cable to the rear camera's connection port. Serra, a [a A For safe driving, arrange the cables to prevent the driver's vision from being obstructed or interfering with driving.
3. Using recording features 3.1 Turning the product on or off The product is turned on automatically and continuous recording starts when you turn on the ACC or start the engine. Wait until the product is completely booted up after turning it on, and then begin operating the vehicle. The video recording does not begin until the product is completely turned an (booted up). 3.2 Learning about file storage locations Videos are stored in the following folders according to their recording mode.