Q1000 User Guide This product records videos while the vehicle is operating. Read and follow the instructions in this guide to properly use and maintain the product.
Before using the product About the product This product records videos while the vehicle is operating. Use this product only for reference when investigating incidents or road accidents. This product is not guaranteed to record for all events. The device may not record accidents with impacts that are too minor to activate the impact sensor or accidents with massive impacts that cause the vehicle’s battery voltage to deviate.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Antennas Statement This radio transmitter (identify the device by certification number or model number if Category II) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
Contents Safety information 5 5. Using THINKWARE CONNECTED 25 1. Product overview 8 5.1 Connecting the product to THINKWARE CONNECTED 25 1.1 Included items 8 8 8 6. Using the PC viewer 26 6.1 System requirements 26 9 6.2 Learning about the PC viewer 26 1.1.1 Standard items 1.1.2 Accessories (sold separately) 1.2 Part names 1.2.1 Front camera (main unit) - front view 1.2.2 Front camera (main unit) - rear view 1.2.3 Rear camera (optional) 9 10 11 1.
Safety information Read the following safety information to properly use the product. Safety symbols in this guide "Warning" - Indicates a potential hazard which, if not avoided, may result in injury or death. "Caution" - Indicates a potential hazard which, if not avoided, may result in minor injury or property damage. "Note" - Provides useful information to help users better utilize the product’s features.
Power supply • Do not operate or handle the power cable with wet hands. Doing so may result in electrocution. • Do not use damaged power cables. Doing so may result in electrical fire or electrocution. • Keep the power cable away from all heat sources. Failure to do so may cause the power cord insulation to melt, resulting in electrical fire or electrocution. • Use the power cable with the correct connector and make sure the power cable is connected securely and is firmly in place.
Other information about the product Product management and operation • Do not separate the product and the mount when the product is turned on. Doing so may result in product malfunction. • Do not expose the product to direct sunlight or intense light. The lens or internal circuitry may fail otherwise. • Use the product at a temperature between 14°F and 140°F (-10°C to 60°C) and store the product at a temperature between -4°F and 158°F (-20°C to 70°C).
1. Product overview 1.1 Included items Ensure that all the items are included when you open the product box. 1.1.1 Standard items Front camera (main unit) Mount Shield film Car charger Adhesive cable holder MicroSD memory card with adapter (consumable) Warranty / CS information The standard items may change without prior notice. 1.1.
Product overview 1.2 Part names 1.2.1 Front camera (main unit) - front view Speaker Outputs the voice guide and buzzer sounds to indicate the product’s status. Manual recording button • Press to start manual recording. • Press and hold for 3 seconds for SOS recording. REC LED Indicates the recording status. GPS LED Indicates the GPS connection status. DC-IN power port Used to connect the power cable. RADAR port Used to connect the RADAR module (optional).
Product overview • To reset the product, press and hold the voice recording ( simultaneously until you hear beeps. ) and manual recording (REC) buttons • Refer to the following table to check the status of the product using the LED indicators. LED Front Security LED Connection LED LED STATUS (light on) The product is turned on.
Product overview 1.2.3 Rear camera (optional) Adhesive mount Used to fix the rear camera in the vehicle. Connection port Used to connect the rear camera to the front camera using a rear camera cable. Rear camera lens Records the rear view. Security LED Indicates that the video is being recorded. Depending on the laws and regulations of the country, the security LED specifications may be different. 1.
2. Installing the product 2.1 Installing the front camera (main unit) Follow the instructions to properly install the product. 2.1.1 Selecting an installation location Select an installation location that can record the entire view in front of the vehicle without obstructing the driver’s vision. Ensure that the front camera lens is located in the center of the windshield.
Installing the product 2 After determining the installation location, wipe the installation location on the windshield with a dry cloth. 3 Attach the shield film to the installation location. ➊ 1 2 ➋ 4 Remove the protective film from the adhesive mount, and then press the mount to the shield film. 2 ➋ ➊1 5 ➊ 1 6 ➋ 2 Remove the product from the mount and push the mount against the windshield to ensure that the mount is firmly fixed.
Installing the product Set the vertical angle of the camera appropriately. D C -I N 7 If the product and mount are not fully connected, the red part of the slide lock will show. To confirm the camera angle, record a video after installation and check the video using the mobile viewer or the PC viewer. If necessary, adjust the camera angle again. For more information about the mobile viewer or the PC viewer, refer to "4. Using the mobile viewer" on page 24 or "6. Using the PC viewer" on page 26. 2.
Installing the product Connect the product to THINKWARE DASH CAM LINK on your smartphone and adjust the camera angle so that the hood of the vehicle covers 1/4 - 1/8 of the screen while viewing the live view screen, as shown in the image to the left. 1/8 1/4 For more information about connecting and using the THINKWARE DASH CAM LINK, refer to "4. Using the mobile viewer" on page 24. 2.2 Installing the rear camera (optional) Refer to the following instructions to properly install the rear camera. 2.2.
Installing the product 2.2.2 Securing the rear camera Refer to the following instructions to secure the product to the installation location. 1 After determining the installation location, wipe the installation surface of the windshield with a dry cloth. Check the installation location before you secure the rear camera to the rear windshield. After securing the rear camera to the windshield, it is hard to remove the camera or change the installation location due to the strong adhesive.
Installing the product 2.2.3 Connecting the rear camera cable Power off the product and connect the rear camera cable to the front camera (main unit). 1 Connect one end of the rear camera cable to the front camera’s V-IN port. 2 Connect the other end of the rear camera cable to the rear camera’s connection port. For safe driving, arrange the cables to prevent the driver’s vision from being obstructed or interfering with driving.
Installing the product 1 Remove the film on the back of the RADAR module. 2 Attach the RADAR module’s adhesive surface to the upper part of the front windshield and press the adhesive part firmly to secure it. Before installation, make sure the RADAR module’s cable length is sufficient and check the cable routing path. 3 Connect the RADAR module to the product’s RADAR connector. N -I C D Check the RADAR connector location again before connecting the module.
3. Using recording features 3.1 Turning the product on or off The product is turned on automatically and continuous recording starts when you turn on the ACC or start the engine. Wait until the product is completely booted up after turning it on, and then begin operating the vehicle. The video recording does not begin until the product is completely turned on (booted up). 3.2 Learning about the file storage locations Videos are stored in the following folders according to their recording mode.
