FN-LINK TECHNOLOGY LIMITD 5th Floor, A Building, Haoye Logistics Park, Shugang Channel, Bao'an District, Shenzhen City, CHINA TEL: 86-0755-29558186 FAX: 86-0755-29558196 Website: www.fn-link.com Product Specification IEEE 802.
FN-LINK TECHNOLOGY LIMITED INDEX 0. REVESION HISTORY…………………………………………………………………………....3 1. INTRODUCTION………………………………………………………………………………….4 1.1 OVERVEIW…………………………………….……………………………………………...4 1.2 SPECIFICATION REFERENCE…………………….………………………………….…...4 1.3 SYSTEM CHARACTERISTICS……………………………………………………………...5 2. MECHANICAL SPECIFICATION………………………………………………………………...6 2.1 OUTLINE DRAWING………………………………………………………………………….6 2.2 CONNECTOR PIN DEFENITION……………………………………………………………6 2.3 LAYOUT GUIDLINE…………………………………………………………………………...7 3.
FN-LINK TECHNOLOGY LIMITED 0. Revision History REV NO Date Modifications Rev1.0 May 11 ,2012 Rev1.1 Dec 30 ,2013 Draft Approved th XJ Hu th SJ LI http://www.fn-link.
FN-LINK TECHNOLOGY LIMITED 1. Introduction F89ESSM23 is a highly integrated and excellent performance Wireless LAN (WLAN) SDIO network interface device. High-speed wireless connection up to 150 Mbps . 1.1 Overview The general hardware for the module is shown in Figure 1. This WLAN Module design is based on Realtek RTL8189ES. It is a highly integrated single-chip 1*1 MIMO (Multiple In Multiple Out) Wireless LAN (WLAN) SDIO network interface controller complying with the 802.11n specification.
FN-LINK TECHNOLOGY LIMITED 1.3 System Characteristics Main Chipset Realtek RTL8189ES Operating Frequency 2.412～2.462GHz WIFI Standard Ieee802.11b/g/n 1*1 Modulation 802.11b: CCK(11, 5.5Mbps), QPSK(2Mbps), BPSK(1Mbps) 802.11 g/n: OFDM PHY Data rates 802.11b: 11,5.5,2,1 Mbps 802.11g: 54,48,36,24,18,12,9,6 Mbps 802.
FN-LINK TECHNOLOGY LIMITED 2. Mechanical Specification 2.1 Outline Drawing 2.2 Connector Pin Definition Pin # Name Description 1 SD_CMD SDIO Command Input 2 SD_D3 SDIO Data Line 3 3 SD_D2 SDIO Data Line 2 4 SD_D1 SDIO Data Line 1 5 SD_D0 SDIO Data Line 0 6 SD_CLK SDIO Clock Input 7 GND POWER GND 8 GND POWER GND 9 ANTENNA RF OUT 10 WAKE Wake Function 11 VDIOSDIO SDIO Voltage 1.8V-3.3V http://www.fn-link.
FN-LINK TECHNOLOGY LIMITED 12 3.3 Power Supply 13 CS PDn 2.3 Layout reference http://www.fn-link.
FN-LINK TECHNOLOGY LIMITED 3. RF Performance 3.1Transmitter Power (Unit in dBm) (Typical 1,6,11 Channel) 11n 20MHz Mode （Spec<9dBm） Mode 11n 20MHz Rate Channel 1 Channel 6 Channel 11 MCS0 8.5 8.3 8.4 MCS3 8.3 8.4 8.3 MCS5 8.5 8.2 8.5 MCS7 8.3 8.5 8.4 Rate Channel 1 Channel 6 Channel 11 MCS0 7.6 7.4 7.3 MCS3 7.5 7.2 7.4 MCS5 7.3 7.5 7.6 MCS7 7.5 7.2 7.3 Rate Channel 1 Channel 6 Channel 11 1Mbps 5.2 5.3 5.5 2Mbps 5.4 5.3 5.5 5.5Mbps 5.6 5.3 5.
FN-LINK TECHNOLOGY LIMITED Mode 11n 40MHz Rate Channel 1 Channel 6 Channel 11 MCS0 -27.3 -27.5 -26.5 MCS3 -27.2 -26.5 -26.4 MCS5 -27.3 -26.5 -26.1 MCS7 -28.3 -28.2 -28.1 3.3 Transmit Center Frequency Tolerance 11g transmit center frequency tolerance test result: Channel CH6 Result(ppm) 0.65 Frequency tolerance 1.57KHz Pass/Fail PASS 11n transmit center frequency tolerance test result: Channel CH6 Result(ppm) 0.71 Frequency tolerance 1.73KHz Pass/Fail PASS 3.
FN-LINK TECHNOLOGY LIMITED MCS3 -77 -77 -77 MCS4 -73 -74 -74 MCS5 -69 -70 -69 MCS6 -68 -68 -68 MCS7 -66 -66 -66 Rate Channel 1 Channel 6 Channel 11 MCS0 -83 -83 -83 MCS1 -79 -80 -80 MCS2 -77 -77 -77 MCS3 -74 -75 -75 MCS4 -71 -71 -71 MCS5 -67 -67 -67 MCS6 -65 -65 -65 MCS7 -63 -63 -63 11n 40MHz Mode: 1RX （Spec≦-60dBm） Mode 11n 40MHz 3.5 Power Consumption Mode Status Power(mW) Note Link 3.3Vx70mA =231 20M 3.3Vx75 mA =248 40M 3.
FN-LINK TECHNOLOGY LIMITED 4.0 Package 4.1 blister packaging Remark: 100pcs/Layer, 10Layer/Bag, 1,000pcs/Bag 4.2 the roll package 2,000pcs/roll http://www.fn-link.
FN-LINK TECHNOLOGY LIMITED 5.0 User’s Manual 5.1 Recommended Reflow curve Referred to IPC/JEDEC standard Peak Temperature : <250°C Number of Times : ≤2 times 5.2 Patch WIFI modules installed before the notice: WIFI module installed note: 1. Please press 1 : 1 and then expand outward proportion to 0.7 mm, 0.12 mm thickness When open a stencil 2. Take and use the WIFI module, please insure the electrostatic protective measures. 3.
FN-LINK TECHNOLOGY LIMITED FCC ID: 2AATL-F89ESSM23 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
FN-LINK TECHNOLOGY LIMITED integrators under the control of the Grantee. Proper measurements of the host device including this RF module (radiated spurious emissions and bandedge) are required to assure compliance with the FCC regulations. http://www.fn-link.
