FN-LINK TECHNOLOGY LIMITED FN-LINK TECHNOLOGY LIMITED 5th Floor, A Building, Haoye Logistics Park, Shugang Channel, Bao'an District, Shenzhen City, CHINA TEL: 86-0755-29558186 FAX: 86-0755-29558196 Website: www.fn-link.com Product Specification IEEE 802.
FN-LINK TECHNOLOGY LIMITED CONTENTS 0 REVESION HISTORY.......................................................................................................................................3 0.1 1 2 3 4 INTRODUCTIONS............................................................................................................................................. 4 1.1 OVERVEIW....................................................................................................................................
FN-LINK TECHNOLOGY LIMITED REV NO Date Modifications Draft Approved Rev1.0 Jul.10,2014 First Released SJ LI SYMEN Rev1.1 Aug.15,2014 Updated the PIN definition SJ LI SYMEN Rev1.2 Aug.20,2014 1. Added Package information; 2. Added Label information; 3. Added the shielding case. SJ LI SYMEN Rev1.3 Oct.30 2014 Added Label information; SJ LI SYMEN 0.1. Model No Definition Example: F88ETUM35-C2 F 88E T U M 3 5-C 2 Control NO: 0, 1, 2….
FN-LINK TECHNOLOGY LIMITED F88ETUM35-C2 is a highly integrated and excellent performance Wireless LAN (WLAN) USB2.0 network interface device. High-speed wireless connection up to 150 Mbps. 1.1 Overview The general hardware for the module is shown in Figure 1. This WLAN Module design is based on Realtek RTL8188ETV. It is a USB2.0 network interface controller complying with the 802.11n specification. It combines a MAC, a 1T1R capable baseband, and RF in a single chip.
FN-LINK TECHNOLOGY LIMITED 2.1 WiFi Specifications Features Descriptions Main Chipset RTL8188ETV Frequency Range 2.400~2.4835GHz Operating Voltage 5.0Vdc ±5% I/O supply voltage WiFi: USB Host Interface Standards Modulation PHY Data rates Transmit Output Power EVM Receiver Sensitivity (HT 20) Operating Channel Media Access Control Network Architecture http://www.fn-link.com WiFi: IEEE 802.11b, IEEE 802.11g, IEEE 802.11n, WiFi: 802.11b: CCK(11, 5.5Mbps), QPSK(2Mbps), BPSK(1Mbps), 802.
Security Antenna OS Supported Dimension FN-LINK TECHNOLOGY LIMITED Infrastructure mode Software AP WiFi Direct WiFi: WPA, WPA-PSK, WPA2, WPA2-PSK, WEP 64bit & 128bit, Onboard Metal ANT Android /Linux/ Win CE /iOS /XP/WIN7 Typical L40.0*W33.0*T3.5mm 2.2 Power Consumption STATUS Power Consumption (mA) LINK 140 TX (11n,20M MCS7) 210 TX (11n,40M MCS7) 180 TX (11g,54M) 220 TX (11b,CCK11) 310 RX 145 3. Mechanical Specification 3.1 Outline Drawing (unit: mm) 3.
FN-LINK TECHNOLOGY LIMITED Pin # Name Description 1 GND Ground 2 D+ USB Data DP 3 D- USB Data DN 4 VDD Supply power input (5V) 5 ON/OFF Control “Enable” of DC-DC, High level defaulted. 3.3 Layout reference http://www.fn-link.
FN-LINK TECHNOLOGY LIMITED 4. Package 4.1 Package information Layer size: L300.0*W240.0 mm Layer material: PVC Carton size: L310.0*W260.0*H220.0 mm Carton material: A=A http://www.fn-link.
FN-LINK TECHNOLOGY LIMITED 5.User’s Manual 5.1 Operating& Storage Conditions Operating Storage MTBF (Mean Time Between Failures) Temperature: -5°C to +55°C Relative Humidity: 10-90% (non-condensing) Temperature: -40°C to +80°C (non-operating) Relative Humidity: 5-90% (non-condensing) Over 150,000hours 5.2 Recommended Reflow Profile Referred to IPC/JEDEC standard. Peak Temperature : <250°C Number of Times : ≤2 times 5.3 Patch WIFI modules installed before the notice: WIFI module installed note: 1.
FN-LINK TECHNOLOGY LIMITED FCC Statement: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
FN-LINK TECHNOLOGY LIMITED IMPORTANT NOTE: This device is intended only for OEM integrators under the following conditions: (1) This module has been designed to operate with Onboard Metal antenna having a gain of 0dBi. The module is only certified with the installed antenna. Any change of the antenna will void the certification. (2) Integration is typically strictly restricted to Grantee himself or dedicated OEM integrators under control of the Grantee.