USER MANUAL Version 1.
Copyright Copyright 2015 All Rights Reserved Manual Version 1.0 The information contained in this document is subject to change without notice. We make no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. We shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
Safety Regulatory Information Caution: Only use approved and UL Listed accessories, battery packs and battery chargers. Do NOT attempt to charge damp/wet mobile computers or batteries. All components must be dry before connecting to an external power source. Power Supply Use only the approved power supply 50-14000-148 output rated 5 Vdc and minimum 2 A. The power supply is certified to EN60950-1 with SELV outputs.
Hearing Aids The wireless device may interfere with some hearing aids. In the event of interference you may want to consult your hearing aid supplier to discuss solutions. Other Medical Devices Please consult your physician or the manufacturer of the medical device, to determine if the operation of your wireless product may interfere with the medical device.
CE Marking and European Economic Area The use of 2.4GHz RLAN's, for use through the EEA, have the following restrictions: Maximum radiated transmit power of 100 mW EIRP in the frequency range 2.400 -2.4835 GHz France, outside usage is restricted to 2.4 - 2.454 GHz. Italy requires a user license for outside usage. Bluetooth® Wireless Technology for use through the EEA has the following restrictions: Maximum radiated transmit power of 100mW EIRP in the frequency range 2.400 -2.
Battery Caution Risk of explosion if battery is replaced by an incorrectly type. Dispose of used battery according to the local disposal instructions. Waste Electrical and Electronic Equipment (WEEE) English: For EU Customers: All products at the end of their life must be returned to the reseller for recycling.
Revision History Version Date 1.
Table of Contents 1 Item Checklist ............................................. 1 1-1 1-2 2 System View ................................................ 3 2-1 2-2 2-3 3 Power On/Off the System .................................................................. 7 Installing the Hand Strap ................................................................... 7 Replacing the Battery ........................................................................ 8 Using the Charging Cradle .........................
1 Item Checklist 1-1 Standard Items a. System b. Charging cradle c. Battery d. Hand strap (with two screws) e. Protection film f.
1-2 Optional Items a. OTG cable 2 b.
2 System View 2-1 Front View No.
2-2 4 Rear View No.
2-3 Specification System P263 P265 Motherboard D31L CPU Baytrail - T CR Z3735F System Memory 2GB DDR3L Flash Memory 32G eMMC LCD Touch Panel LCD Size 7" 10.1” Interface Resolution Touch Screen MIPI 1280 x 800 1920 x 1200 P-CAP 5 points Multi-touch Wireless Networking Wireless LAN 802.11 a/b/g/n, 2.4G/5GHz Bluetooth 4.
System P263 P265 Motherboard D31L Battery & Power Battery 8000 mAh, 3.7V, 29.6 Wh *2 Certificate EMC & Safety FCC Class B / CE Mark / UL Environment Sealing Fall Security Operating Temperature (Not in charging mode) Operating Temperature (running charging mode) IP54 (display side) 1.
3 Getting Started 3-1 Power On/Off the System 1. 3-2 Push the power button to turn on the system and hold 4~5 seconds to turn off the system. Note: For best touch performance, remove the protective plastic overlay from the LCD screen by peeling it away from one of the corners. Be sure to use a soft pointing device or finger tip to avoid scratching the screen during normal use. Installing the Hand Strap 1. Attach the hand strap to the back of the system and fasten the screws (x2) to secure it.
3-3 8 Replacing the Battery 1. Loosen the pen screw counter-clockwise on the battery cover. 2. To remove the battery pull the plastic tab aside and gently lift the battery out of the system. 3. To install the battery put the battery in the slot and push until the battery clicks into place.
3-4 Using the Charging Cradle 1. 3-5 Connect the USB-AC adapter to the connector on the bottom of the cradle charger and the power outlet. Connect to Other Device 1. Connect the OTG USB cable to the connector on the bottom of the cradle charger and connect the other end to a PC to synchronize the two devices.
3-6 Replacing a Micro SD Card 1. Loosen the pen screw counter-clockwise on the battery cover. 2. To install a Micro SD card insert the Micro SD card into slot until it snaps in place. To remove the Micro SD card just push the card again and slide it outwards. 3.
3-7 Installing the 3G Card 1. 2. Loosen the screw(x1) to remove cover of 3G card slot. Inset the 3G card until it snaps in place. Finally screw the cover back.
4 Application Programming Interface Operating System The API operation has been verified with the following operating systems: Microsoft Windows 7 32/64 bit Microsoft Windows 8 32/64 bit EC Version 12 or later version can support 12
4-1 OpenFunKeyLib [Function] This opens the Function Key API service. [Format] int OpenFunKeyLib(char *FunKeyControlVersion) [Argument] uchar *FunKeyControlVersion → get EC version. [Return Value] If opening service was successful, the return SV_ERROR_SUCCESS value, If there is can’t found EC control, the SV_ERROR_FAILED_NO_FOUND_DEVICE are returned, if return SV_ERROR_FAIL the service can’t form EC control get return value.
4-2 SetFunKey1 [Function] Set Button 1 output key. [Format] int SetFunKey1(const char* SetKey, bool ButtonEnable) [Argument] const char* SetKey → Set button1 output key. bool ButtonEnable → Enable/Disable key output. Trur is enable, False is disable. [Return Value] If set value successful, the return SV_ERROR_SUCCESS value. If there is an error, the SV_ERROR_FAIL are returned.
4-3 SetFunKey2 [Function] Set Button 2 output key. [Format] int SetFunKey2(const char* SetKey, bool ButtonEnable) [Argument] const char* SetKey → Set button1 output key. bool ButtonEnable → Enable/Disable key output. Trur is enable, False is disable. [Return Value] If set value successful, the return SV_ERROR_SUCCESS value. If there is an error, the SV_ERROR_FAIL are returned.
4-4 Appendix A: KeyMap.
[FunctionKey] {Return}=28 {F11}=44 {NumLock}=53 {KeypadPointDelete}=63 {Escape}=29 {F12}=45 {KeypadDivision}=54 {KeyboardPower}=66 {Backspace}=2A {PrintScreen}=46 {KeypadMultiplication}=55 {KeyboardVolUp}=80 {Tab}=2B {ScrollLock}=47 {KeypadSubtraction}=56 {KeyboardVolDn}=81 {Space}=2C {Break}=48 {KeypadAdd}=57 {CapsLock}=82 {CapsLock}=39 {Pause}=48 {KeypadEnter}=58 {NumLock}=83 {F1}=3A {Insert}=49 {Keypad1End}=59 {ScrollLock}=84 {F2}=3B {Home}=4A {Keypad2Down}=5A {LeftCtrl}=E0
[MediaKey] (ScanNextTrack)=00B5 (VolumeDown)=00EA (WWWSearch)=0221 (ScanPreviousTrack)=00B6 (BassUp)=0152 (WWWHome)=0223 (Stop)=00B7 (BassDown)=0153 (WWWBack)=0224 (Play/Pause)=00CD (TrebleDown)=0155 (WWWForward)=0225 (Mute)=00E2 (MediaSelect)=0183 (WWWStop)=0226 (BassBoost)=00E5 (Mail)=018A (WWWRefresh)=0227 (Loudness)=00E7 (Calculator)=0192 (WWWFavorites)=022A (VolumeUp)=00E9 (MyComputer)=0194 [SpecialKey] =1111 18
