User Manual Version 1.
Copyright Copyright 2011 All Rights Reserved Manual Version 1.0 The information contained in this document is subject to change without notice. We make no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. We shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
Safety Regulatory Information Caution: Only use approved and UL Listed accessories, battery packs and battery chargers. Do NOT attempt to charge damp/wet mobile computers or batteries. All components must be dry before connecting to an external power source. Power Supply Use only the approved power supply 50-14000-148 output rated 5 Vdc and minimum 2 A. The power supply is certified to EN60950-1 with SELV outputs.
Hearing Aids The wireless device may interfere with some hearing aids. In the event of interference you may want to consult your hearing aid supplier to discuss solutions. Other Medical Devices Please consult your physician or the manufacturer of the medical device, to determine if the operation of your wireless product may interfere with the medical device.
CE Marking and European Economic Area The use of 2.4GHz RLAN's, for use through the EEA, have the following restrictions: Maximum radiated transmit power of 100 mW EIRP in the frequency range 2.400 -2.4835 GHz France, outside usage is restricted to 2.4 - 2.454 GHz. Italy requires a user license for outside usage. Bluetooth® Wireless Technology for use through the EEA has the following restrictions: Maximum radiated transmit power of 100mW EIRP in the frequency range 2.400 -2.
Battery Caution Risk of explosion if battery is replaced by an incorrectly type. Dispose of used battery according to the local disposal instructions. Waste Electrical and Electronic Equipment (WEEE) English: For EU Customers: All products at the end of their life must be returned to the reseller for recycling.
Revision History Version Date 1.
Table of Contents 1 Introduction ................................................. 9 1-1 1-2 2 1-1-1 Front View .................................................................................... 9 1-1-2 Rear View ................................................................................... 10 Specification ..................................................................................... 11 Getting Started .........................................
1 Introduction 1-1 System Overview 1-1-1 Front View No.
1-1-2 Rear View 10 No.
1-2 Specification System P263 Motherboard D31 CPU System Memory Flash Memory Bay-Trial T Z3745 2GB LPDDR3 / 4GB LPDDR3 32G eMMC LCD Touch Panel LCD Size Resolution Touch Screen 7" 1280 x 800 P-CAP 5 points Multi-touch Wireless Networking Wireless LAN 802.11 a/b/g/n, 2.4G/5GHz Single SSID Yes Fast Wi-Fi roaming ( Max:2 sec ) Yes Always on Wi-Fi Yes No popup of neighbor networks selectable by end users Bluetooth NFC Yes 4.
System P263 Motherboard D31 Peripheral Camera MSR Hand strap IC card reader Scanner 5MP ( Rear side) 3 Tracks MSR 1 Smart IC Card Reader (Optional) 1D/2D Barcode Scanner (Optional) Cradle USB Port Power Adapter mini-USB 2.0 x 1 10W / 5V Battery & Power Battery 8000 mAh, 3.7V, 29.
2 Getting Started 2-1 Power On/Off the System 1. Push the power button to turn on the system and hold 4~5 seconds to turn off the system. Note: For best touch performance, remove the protective plastic overlay from the LCD screen by peeling it away from one of the corners. Be sure to use a soft pointing device or finger tip to avoid scratching the screen during normal use.
2-2 14 Replacing the Battery 1. Loosen the pen screw counter-clockwise on the battery cover. 2. To remove the battery pull the plastic tab aside and gently lift the battery out of the system. 3. To install the battery put the battery in the slot and push until the battery clicks into place.
2-3 Using the Charging Cradle 1. Connect the USB-AC adapter to the connector on the bottom of the cradle charger and the power outlet.
2-4 Replacing a Micro SD Card 1. Loosen the pen screw counter-clockwise on the battery cover. 2. To install a Micro SD card insert the Micro SD card into slot until it snaps in place. To remove the Micro SD card just push the card again and slide it outwards. 3.
2-5 Synchronization 1. 2-6 Connect the USB cable to the connector on the bottom of the cradle charger and connect the other end to a PC to synchronize the two devices. Using the Charging Cradle 1. Attach the hand strap to the back of the system and fasten the screws (x2) to secure it.
