User Manual Revision v1.
Copyright 2011 All Rights Reserved Manual Version 1.4 Part Number: 3LMKK9380114 The information contained in this document is subject to change without notice. We make no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. We shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
Safety IMPORTANT SAFETY INSTRUCTIONS 1. 2. 3. 4. 5. 6. 7. 8. 9. To disconnect the machine from the electrical Power Supply, turn off the power switch and remove the power cord plug from the wall socket. The wall socket must be easily accessible and in close proximity to the machine. Read these instructions carefully. Save these instructions for future reference. Follow all warnings and instructions marked on the product. Do not use this product near water.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
compliant. 4.7.3.2 Materials for fire enclosures For MOVABLE EQUIPMENT having a total mass not exceeding 18kg.the material of a FIRE ENCLOSURE, in the thinnest significant wall thickness used, shall be of V-1 CLASS MATERIAL or shall pass the test of Clause A.2. For MOVABLE EQUIPMENT having a total mass exceeding 18kg and for all STATIONARY EQUIPMENT, the material of a FIRE ENCLOSURE, in the thinnest significant wall thickness used, shall be of 5VB CLASS MATERIAL or shall pass the test of Clause A.
Revision History Changes to the original user manual are listed below: Version Date Description 1.0 2009 July Initial release 1.1 2009 Sep Add Arm installation 1.2 2009 Sep Add Arm application condition Modified connector wording 1.3 2010 May B68 motherboard added Jumper Setting updated 1.
Table Contents 1 Item Checklist .................................... 1 1-1 Standard Items ..........................................................1 2 System View ...................................... 2 2-1 2-2 2-3 2-4 Front View .................................................................2 Rear View ..................................................................3 Side View...................................................................4 I/O View ..............................................
1 Item Checklist Take the system unit out of the carton. Remove the unit from the carton by holding it by the foam inserts.
2 System View 2-1 Front View ① ④ ② ③ Number 2 Description 1 Camera 2 TV key pad (Power, volume and channel button) 3 Smart card reader slot 4 Phone set holder
2-2 Rear View ① ⑦ ⑥ ⑤ ④ ② ③ ⑧ ⑧ Number Description 1 Ventilation 2 VESA holes 3 Rear I/O (USBx2, DC-IN, RJ48 , LAN connector) 4 Phone set holder 5 RFID sensor 6 Smart card reader slot 7 MSR slot (optional) 8 Speakers 3
2-3 Side View ① ② Number 4 Description 1 Smart card reader slot 2 MSR slot (optional)
2-4 I/O View ① ⑤⑥⑦ Number ②③④ ⑧ Description 1 USB x 2 2 SCSI connector 3 USB x 1 4 Phone jack (RJ11) 5 Audio line-out 6 Audio MIC-in 7 Built-in MIC 8 Smart card reader slot 5
3 Peripheral Installation 3-1 Phone Set Installation a. Slide the phone module into the phone set holder as the arrow shown in the picture. b. Connect the phone cable to the connector on the phone module. c. Connect the other end of the phone cable to the connector on the system.
3-2 Arm Installation a. Connect the cables to the system b. Fasten the screws(x4). Note: Only use concrete walls to fix the Arm (and wall box) to.
4 Specification Model Name Motherboard K938 B98 B68 Intel Core Duo(L2400) CPU Supports 1.66G/2MB/667MHz 65nm Intel Atom N270 1.6G C48 Intel Pineview dual core Micro-FCBGA Chipset System Memory Intel 945GME + ICH7M Intel 945GSE + ICH7M D525 1.8G Intel Pineview CPU processor + ICH8M 2 x DDR2 SO-DIMM slot, 2 x DDR2 SO-DIMM slot, 2 x DDR3 SO-DIMM slot, up up to 4 GB up to 2 GB LCD / Touch Panel Display Size 18.
Motherboard B98 B68 C48 Certificate EMC & Safety UL FCC Class B, CE, LVD UL 60601 Dust & Water Proof UL 60950 - IP 54 (including front bezel / web cam) Environment Operating Temperature 0°C ~ 35°C (32°F ~ 104°F) Storage Temperature -20° ~ 60°C (-4°F ~ 140°F) Operating Humidity 5% - 95% RH non-condensing Storage Humidity 5% - 95% RH non-condensing Communication & peripherals Speaker 2 x 3W Speaker Handset & Cradle 1 Magnetic stripe card optional reader(Optional) Camera ( Built-in) o
5 Jumper Settings 5-1 B98 Motherboard 5-1-1 10 Motherboard Layout
5-1-2 Connectors & Functions Connector Function CN3 Audio Line Out CN4 MIC In CN5 / SW3 Power On Button CN6 Power LED CN7 +24V/+19V CN8 Speaker & MIC Connector CN9 LAN LED CN11 CD-IN Connector CN12 LVDS CN13 IrDA CN14 Inverter CN15 COM5 Touch CN16 SATA Power CN18 USB CN19 Card Reader CN20 FT Status CN21 / PWR3 DJ-Jack CN22 Hardware Reset CN23 for Beside (+12V_CRT) DDR_B1 DDR2 DIMM PRN3 Printer Port RJ11_3 Cash Drawer RJ45_3 LAN RJ45_4 COM Port U31 NB JP3
5-1-3 Jumper Setting COM2 RS232/485/422 Setting Function JP6 (1-2) (3-4) (5-6) (7-8) (9-10) (11-12) JP4 (1-2) (3-4) (4-6) (5-7) (7-8) (9-10) ▲RS232 RS485 RS422 Cash Drawer Power Setting Function JP3 (1-2) (3-4) 5-6) +12V ▲+19V Power Mode Setting Function ▲ATX Power AT Power 12 JP11 (1-2)
COM3 & COM4 Power Setting JP5 Function (1-2) (3-4) (5-6) (7-8) (9-10) (11-12) ▲RI COM3 Pin10 +5V +12V ▲RI COM4 Pin10 +5V +12V CMOS Operation Mode Function JP7 (1-2) ▲CMOS Normal CMOS Reset 13
System Indicator JP12 Function (1-2) (3-4) 5-6) (7-8) Disable ▲Enable LCD ID Setting 14 LVDS Bits Channel Output Interface 1366 x 768 24 Single LVDS 2 1440 x 900 24 Dual LVDS 4 1920 x 1080 24 Dual LVDS 5 1024 x 768 24 Single LVDS 6 1280 x 1024 24 Dual LVDS 7 800 x 600 24 Single LVDS 9 1024 x 768 18 Single LVDS 11 800 x 600 18 Single LVDS Panel # Resolution 1 JP8 (1-2) (3-4) (5-6) (7-8)
12 800 x 600 18 Single LVDS CRT Remark: Panel ID #12 is only applied for Sharp 12” LQ121S1LG41 / LQ121S1LG42 panel.
5-2 B68 Motherboard 5-2-1 16 Motherboard Layout
5-2-2 Connectors & Functions Connector Function BAT1 CMOS Battery Base ( Use CR2023) CN1 Power On Button CN2 Touch Sensor CN3 Power LED CN4 SATA1 HDD Power Connector CN5 SATA2 HDD Power Connector CN6 LCD Interface Connector CN7 IrDA Connector CN8 For External Touch Connector CN9 Inverter Connector CN10 Card Reader Connector CN11 Line Out CN12 LED Power CN13 MIC In CN14 Speaker & MIC CONN CN15 CD-IN CONN CN17 LAN LED CN18 USB5 CN19 DC-JACK CN20 PS2 KEYBOARD CN21 F
5-2-3 Jumper Setting Power Mode Setting Function JP9 (1-2) JP8 (1-2) ATX Power ▲AT Power CMOS Operation Mode Function ▲CMOS Normal CMOS Reset LCD ID Setting LVDS Panel # 18 Resolution Bits Channel ▲1 1366 x 768 24 Single 2 1440 x 900 24 Dual 4 1920 x 1080 24 Dual 5 1024 x 768 24 Single Output Interface LVDS Panel LVDS Panel LVDS Panel LVDS Panel JP7 (1-2) (3-4) (5-6) (7-8)
6 1280 x 1024 24 Dual 7 800 x 600 24 Single 9 1024 x 768 18 Single 11 800 x 600 18 Single 12 800 x 600 18 Single LVDS Panel LVDS Panel LVDS Panel LVDS Panel LVDS Panel CRT Remark: Panel ID#12 is specialized for Sharp 12.1” LQ121S1LG41/ LQ121S1LG42 panel.
5-3 C48 Motherboard 5-3-1 20 Motherboard Layout
21
5-3-2 Connectors & Functions Connector 22 Function CN1 Power Button Connector CN3 Printer Port Reset CN4 Printer Port CN5/8 HDD Power CN11 COM5 For Touch CN13 Card Reader Connector CN14 Line out CN15 HDD LED CN16 Speaker & MIC CN18 MIC IN CN20/JP10 System Indicator CN22 USB Port CN23 PS2 KEYBOARD CN26 LVDS CN27 Inverter Connector CN29 System Fan DDR3_A1 DDR3 SO-DIMM1 DDR3_A2 DDR3 SO-DIMM2 PRN1 Parallel Port PWR1 +19V DC Jack RJ11_1 Cash Drawer Connector RJ45_1
5-3-3 Jumper Setting COM2 RS232/485/422 Setting Function JP5 JP4 ▲RS232 RS485 RS422 Cash Drawer Power Setting Function JP19 +19V ▲+12V Power Mode Setting Function JP9 ▲ATX Power AT Power 23
System Reset Function JP12 ▲System Normal System Reset System Indicator Function JP10 ▲Disable Enable Inverter Selection Function ▲CCFL LED 24 JP14
CMOS Operation Mode CMOS Reset To clear the CMOS, 1. Remove the power cable from the system. 2. Open the system, and set the ‘CMOS Operation jumper’ from ‘CMOS Normal’ to ‘CMOS Reset’. (refer to the jumper shown below) 3. Connect the power cable to the system, and power on the system: in ATX mode: press the power button and it will fail power on in AT mode: turn on system power 4. Remove the power cable from the system. 5. Return the "CMOS Operation mode" jumper setting from "CMOS Reset" to "CMOS normal".
COM3 & COM4 Power Setting COM3 and COM4 can be set to provide power to your serial device. The voltage can be set to +5V or 12V by setting jumper JP18 on the motherboard. When enabled, the power is available on pin 10 of the RJ45 serial connector. If you use the serial RJ45 to DB9 adapter cable, the power is on pin 9 of the DB9 connector. By default, the power option is disabled in the BIOS. Enable COM3/COM4 power in BIOS 1.
COM3/COM4 Power Setting Function JP18 ▲+5V COM3 +12V +5V COM4 ▲+12V LCD ID Setting Several configurations are applied to different sizes of panel. Please refer to the followings to complete relevant settings.
1024 x 768 18 Single 1280 X 1024 24 Dual *Note: specialized for Sharp 12.1” LQ121S1LG41/LQ121S1LG42 panel. LCD Brightness Control Setting Please note Brightness Control can only be set by setting jumper JP14 for CCFL on the motherboard C48 V2.1. By default, the inverter is CCFL on the motherboard jumper setting. 1. 2. 3. 4. 28 Power on the system, and press the key when the system is booting up to enter the BIOS Setup utility.
2nd VGA Power Setting VGA port power must be on through BIOS/Utility for default is “No Power“ 1. 2. 3. 4. Power on the system, and press the key when the system is booting up to enter the BIOS Setup utility. Select the Advanced tab Select "Power Configuration COM/VGA Ports" and press to go to display the available options. To switch on the power, select "+12V" press .
6 Appendix Drivers Installation: The shipping package includes a Driver CD. You can find every individual driver and utility that enables you to install the drivers in the Driver CD. Please insert the Driver CD into the drive and double click on the “index.htm” to pick up the models. You can refer to the drivers installation guide for each driver in the “Driver/Manual List”.
