User's Manual
FTr16S
接收机 Receiver
http://www.flysky-cn.com
Copyright ©2019 Flysky Technology co., ltd
FTr16S 是一款专用于穿越机的双天线双向传输接收机，采
用了 AFHDS 3。它体积小巧便于安装，可输出标准 PPM
信号和 i-BUS 信号。
The FTr16S is a double antenna bidirectional receiver using
the AFHDS 3 protocol. It's compact, easy to install and can
output using a standard PPM or i-BUS signal.
产品介绍
Introduction
接收机概览
Receiver overview
用于连接接收机与模型的各个部件。
VCC：电源电压为 3.5~8.4V。
PPM 信号接口：输出标准的 PPM 信号。
i-BUS 信号接口：用于输出 i-BUS 信号。
SENS: 传感器。
GND：连接地线。
These ports connect the receiver to various models,
component's and flight controllers.
VCC: Power supply voltage from 3.5 – 8.4V.
PPM signal port: Outputs standard PPM signal.
i-BUS signal port: Outputs i-BUS signal.
SENS: Sensor.
GND: Connect to ground wire.
注意事项：
使用前必须确保本产品与模型安装正确，否则可能导致模型发生严重损坏。
关闭时，请务必先关闭接收机电源，然后关闭发射机。如果关闭发射机电源时接收机仍然在工作，将有可能导致遥控设备失控或者引
擎继续工作而引发事故。
确保接收机安装在远离电机，电子调速器或电子噪声过多的区域。
接收机天线需远离导电材料，例如金属棒和碳物质。为了避免影响正常工作，请确保接收机和导电材料之间至少有 1 厘米以上的距离。
准备过程中，请勿连接接收机电源，避免造成不必要的损失。
此接收机的接收信号的距离比回传距离远，当超出回传距离后，部分发射机会有报警提示，此为正常现象。此报警提示音部分发射机
可以通过设置发射机关闭，如 NV14, FS-i10，Paladin (PL18)。
Attention:
Make sure the product is installed and calibrated correctly, failure to do so may result in serious injury.
Make sure the receiver's battery is disconnected before turning off the transmitter, failure to do so may lead to unintended operation
or loss of control.
Make sure the receiver is mounted away from motors, electronic speed controllers or any device that emits excessive electrical noise.
Keep the receiver's antenna at least 1cm away from conductive materials such as carbon or metal.
Do not power on the receiver during the setup process to prevent loss of control.
The receiver can receive at distances further than it can transmit from. When the receiver goes out of its transmission range, some
transmitter's will sound the lost signal alarm. This is normal, the lost signal alarm can be turned off in the settings for transmitters
such as the NV14, FS-i10 and Paladin (PL18).
对码
Binding
1. 将发射机进入对码状态；（发射机进入对码状态的方式可能不同，请根据发射机的使用说明书进行操作）
2. 按住接收机对码键同时接通电源，LED指示灯绿色快闪即进入对码状态；
接收机对码成功后，LED指示灯绿色常亮，即可与发射机正常通信；
接收机未对码或者掉码后，LED指示灯红色慢闪；
接收机发生硬件错误时，LED指示灯红色常亮。
3. 检查发射机、接收机、模型是否正常工作。如需重新对码，请重复以上步骤重新对码。
1. First put the transmitter into bind mode (see the transmitter's user manual for instructions on how to activate bind
mode.)
2. Press receiver's bind key and connect the receiver to power at the same time. The receiver's green LED will start to flash
quickly indicating that it has entered bind mode.
When the receiver's green LED stops flashing the transmitter and receiver have successfully bound.
When the receiver's red LED flash slowy indicating losing signal.
天线
天线
VCC
GND SENS
PPM i-BUS
对码键