Honey q \ Touching Infinity Copyright ©2019 Fly sky Technology co. ltd os 2.4C 14.
Thank you for purchasing our product, an ideal radio system for beginners or experienced users alike. =F Read this manual carefully before operation In order to ensure your safety, and the safely’ of others or the safe operation of your system. If you encounter any problem during use, refer to this manual Erst.
1. 1.1 Safety Symbols 1.2 Safety Guide .. 2. Battery Safety In Instructions . 3. 3.1 System Features 3.2 Transmitter Overview 3.2.1 Transmitter Antenna 3.3.2 Stick/Switche/Knob/Button . 3.2.3 Status Indicator. 3.2.4 Trim Switch. 3.2.5 Gimbals Mod 3.2.6 Throttle Mode .. 3.2.7 Power Buttons 3.3 Receiver Overview 3.3.1 Receiver Antenna 3.3.2 Status Indicator . 3.33 Ports... 4, Pref light SEEP cvvensrvenmreensinsisisensenend 4.1 Receiver and Servo Installation 5. Operation 5.1 Power On 5.2 Binding. 5.
.10 Helicopter Structure, 9.11 Swash plate type.. 10. Quadcopter excursive 10.1 Attitude. AZ 11.Quad expert mode exclusive 11.1 Throttle held... 11.3.1 Function Delay. 11.3.2 Channel Delay . 11.3.3 Conditions Del 11.4 Mixes cen 114.1 Linear Miss. 11.4.2 Curve Mixes. 11.5 Conditions 3 12.Engineering ve venison did 12.1 Multiplex sticks. 44 13.Receiver Settings 13.1 Binding with receive: 13.2 Fail safe. 13.3 Range Tes 13.4 Receiver Protocol 13.5 i-BUS settings. 13.6 RX Battery Monitor. 13.
CHRYSLER 1.Safety 1.1 Safety Icons Pay attention to the following icons and their meanings. Failure to follow these guidelines can result in equipment damage or personal injury. A WARNING [+ Hot following these Instructions may lead to minor injuries, A CAUTION Hot following these instructions may lead to major injuries. A DANGER + Not following these instructions may lead to serious injuries or death. 1.
Paladin 2.Battery Safety Instructions A Danger This products battery is rechargeable and non-removable. Do not remove the battery from the product. Do not charge batteries that show any evidence of damage, aging, leakage or exposure to liquids. O) Do not expose the battery to liquids. BE Do not use a damp battery. Keep your hands try during use and do not leave batteries in areas with lots of moisture. Do not touch the positive and negative terminals of the battery together.
CHRYSLER 3.Product Description The PL transmitter and Airlift receiver are an 18 channel 2.4GHz AFFORDS 3 (Third generation automatic frequency hopping digital system) system compatible with fixed-wing, glider, helicopter, quad copter and various other vehicles. 3.1 System Features AFHDS3 {third-generation automatic frequency hopping digital system) is a newly developed digital wireless system.
Paladin 3.
Back View: [25] Right Gimbals [35] [26] TR4 Button [36] [27] TRE Trim [37] [28] Trim [38] [29] Doorknob [39] [30] Power Button [40] [31] Bluetooth Module Port [41] [32] FRM30L Status Indicator [42] [33] FRM301 Button [43] [34] Gamble Tension Adjustment [44] [36] [37 [38] [39] Grip Micro USB Port Trainer Port Grip FRM301 Press to release FRM301 FRM301 RF Module Gimbals Tension Adjustment Grip RF Module Port Wireless Charging Area IIb.
Paladin 3.2.1 Transmitter Antenna The PL has a built in antenna with no need for manual adjustment. A Note + To ensure a good signal do not cover or block the antenna, 3.2.2 Stick/Knob/Switch/Button The PL has 2 sticks, 6 switches, 5 knobs and 2 buttons. + Gimbals to control the aileron (also known as roll}, lift (also known as pitch), throttle and rudder. = Switch:Used to control the auxiliary channels or to switch control states. « Knob: Used to control the auxiliary channels.
When the counterclockwise adjustment is rouge, entire range of movement of the screw Is about 3mm. Be cautious not to stadium it too Tar or the screw will fall out. Legible Front view 3.2.6 Throttle Mode You can select [Non Self-returning] or [Self-return and Non self-return], the system defaults [Non Self-returning] then adjust the gimbals as needed to match the mode.
Paladin 3.2.7 Power Buttons To prevent the system from being powered on or off by mistake the PL uses a dual power button system. Press and hold both power bunions to power on the transmitter, 3.3 Receiver Overview SERVED SENS BIND aria Port LED 3.3.1 Receiver Antenna The FTr10 uses AFFORDS 3 (3rd Generation Automatic Frequency Hopping Digital System} with dual antenna bidirectional transmission, 2 caution Do not pull, bend or tie the receivers antenna or connect it te a serve.
CHRYSLER 4. Preflight Setup Follow the instructions and guidelines in this chapter before use. 4.1 Receiver and Servo Installation Make sure that the receiver is mounted in an appropriate location within the model, to ensure a stable signal, maximum range and to mitigate external interference, follow these guidelines: Pay attention to the following when installing the receiver: Make sure the receiver is not installed near Es Cs or other sources of electrical noise.
Paladin perpetration Guidelines Once the model is set up follow these guidelines to set up the transmitter and receiver, 5.1 Power On Follow the steps below to power on: ll. Check to make sure the receiver is installed correctly and that the receiver is powered off 2. Press and hold both power buttons until the screen lights up. B. Power on the receiver. A Note + The system is now active, be cautious to not cause damage or personal injury.
CHRYSLER 5.3 Pref light Checks Always perform the following steps before each flight: 1. Inspect the entire system to make sure that everything is working ss expected 2. Perform arrange test as outlined in the [13.3 Range Test] section of the user manual A DANGER |» Do not use the model if there are any abnormal behaviors during the test. A DANGER |» Do not exceed the maximum rated range during use. A CAUTION |» Ambient interference caused by other signal sources may cause interference, 5.
Paladin 6. Ul This is an interdiction to the transmitter’ Overview The main interface displays information related to the model such as sensor information and function status, Mode! name Receiver power status Transmitter power status Function menu icon Signal strength Sen so information Timer Status Bai Left stick tri Right stick trim position (UP position (UP/DOWN) DOWN) Model type Left stick trim position (LEFT/ RIG it stick trim Lock scree: position (LEFT/RIGHT) button 6.1.
CHRYSLER 6.1.2 Quick Access {Touch this area to access the [Sensor selection menu] Up to 4 sensors can be displayed. For more information refer to section [7.17] of this manual, Touch this area to access the [Timer] settings menu. For more information refer to section [7.11] of this manual. (Touch this are to access the [Aircraft Structure] menu. | For more information refer to section [7.16] of this manual. 6.2 Menu Ul This section is a quick introduction on how to use the UI 6.2.
Paladin 7.General Function Settings This chapter introduces the main system functions. 7.1 Reverse Function This function reverses the direction of motion for each channel. Function Settings: This function can reverse the direction of travel for all 18 channels. [Marmoreal: indicates that this channel output is the default direction: [Reverse indicates that the channel s direction of travel has been reversed.
CHRYSLER 7.3 Sub trim This function is used to adjust the center point of each channel. Due to the structure of some models the servos center point may need to be adjusted so that when at rest all the control surfaces line up properly. When using this function make sure that the stick, knob etc. is at i Function Settings: This function adjusts the Busting of all 18 channels thin a range of 130% to 170%, Steps: lL. Celesta channel 2. Use the + and icons to adjust the channels center point. 7.
Paladin Function Settings: [Ratio]: Clamps the maximum and minimum value and 2s 2 resell reduces the steepness nf the curve. EXP: How much curve is added to the line. It can be adjusted between 1009 and +1009. The bos highlighted in light preen is the currently selected setting. The horizontal axis on the graph is the stick/knob/input’ rue position, The vertical axis on the graph is the adjusted output. ‘the red line is the current relationship between input and output.
CHRYSLER 7.6 Throttle Curve This function changes the output curve for the throttle channel. A curve can be created using 3 11 different points so that the user has much better control of the aircraft’ s engine. Curve can also be set in the EXP function. Function settings: This function supports two different types of curve a / curve and a ¥ Clive Each curve type can be Set fo have between 3 and 11 points.
Paladin Function Settings: Idle Up can bat set to a value Between 0 and 100%. i [idle up (non ell means that no switch is assigned to the Idle up function and as such is not active. When g switch is assigned to iE will be shown in the brackets, for example lied up (5wA)l: The percentage to the right of the switch notification indicates the channel position when the function is active. [0]: located below the channel bar indicates which function is active and inactive. [Onl Indicates which function is active.
CHRYSLER Function settings: The conditions fund lion can hold up to 5 different data less, cache of which can be copied. pasted and renamed In order to activate a condition it mist be assigned fo a switch, «The currently selected condition can be sec at the heme screen Sea [6.1 for more details. 1 Select s condition. Camel: Displays the conditions name. {Copy Copies the conditions settings to another condition. 2. Touch [Name] and use the on-screen Biosensor To snr 8 ry name.
Paladin 7.11 Timer Select from a variety of timers to keep tracking of things such as, flight time, lap time etc. [Model/Engine timer]: Used to keep track of flight time. Function Settings: 1. Touch Model or Engine timer, then touch the [] icon 16 activate the timer. 2.
CHRYSLER Function Settings: This function can be use for channels Touch vel icon to activate the function then select channel 2. select [Sick or Knob, (Basie Function], {Output Channel or [Nobel in the list [Joystick/Knob) means that the channel signal output from the student’ s radio will be processed by all functions of the trainers roadie. Sticks, knobs, Vengeance (PIC, a) can be selected. [Basic function] means that the signal slitter from the student’ s radio will be processed by the trainer 5 radio.