User Manual IP622C/IP622CWP V1.0 Revision Record: Version Date V1.0 201-8-3 Author Sherry Firmware Version Applicability V1.0 1 V1.0 Revision time: 2015-12-08 20:00 Copy Right 2015 All Rights Reserved by Flyingvoice Technology CO.
Table of Contents 1 Introduction...........................................................................................................................................................................................................................................................................................................1 1.1 Thanks for Purchasing IP622C/IP622CWP.........................................................................................................................................
7.4.2 Syslog........................................................................................................................................................................................................................................................................................... 31 7.5 SIP Account......................................................................................................................................................................................................
1 Introduction 1.1 Thanks for Purchasing IP622C/IP622CWP Thank you for purchasing IP622C/IP622CWP. The IP622C/IP622CWP which has 2 lines is a full-featured VoIP (Voice over Internet Protocol) phone that provides voice communication over an IP network. This phone functions not only much like a traditional phone, allowing to place and receive calls and enjoy other features that traditional phone has, but also it own many data services which you could not expect from traditional telephone.
2 Installing 2.1 Assembling the Phone and Connecting to the Network 1) Plug one end of the coiled phone cord into the left side of the phone base. 2) Plug the other end of the handset cord into the jack at the bottom of the handset. 3) If you are using an external power source, push the power cord into the power supply, and plug the power supply into the phone base unit. Note: Use only the power supply that came with the phone.
Notice: If the phone does not provide this screen, re-confirm installation and connections. If these are incorrect, try unplugging the phone and plugging it back in again. If you still don’t see the display, then contact your Phone Administrator or service provider. 2.4 Connect to the Internet You can connect the FIP11/FIP11W/FIP11WL to the Internet via wired and via wireless. 2.4.1 Via Wired Step 1.Check FIP11/FIP11W/FIP11WL have powered on correctly. Step 2.
Step 3.Press the button to connect to the E3CALL_SZ. Step 4.If the Wi-Fi need authentication, choose the authentication and fill in the password, then choose the button to connection Step 5.If the AP have connected, then connection status will change like following picture and the icon of wireless will display linked.
3 Get Familiar with IP622C/IP622CWP 3.1 Front Panel Front Panel No. 1 Description of function Handset top cradle For the placement of handset (Receiver end) Hook switch For hang-up and hang-off of handset Cradle latch To prevent the handset from dropping when it is wall-mounted.
Soft keys These keys are used as soft keys. These can be used for item selection or control on the LCD screen. The softkey’ function depends on their corresponding content displayed on the LCD at that time. 6 Menu Press it to access to menu items: such as phonebook, multi-functional key, and call history and so on.
3.2 Rear Panel Part Name Rear Panel Description of function Headset Headset console, connect to headset(This is on the right side of the phone.) DC 5V Power port PC Connects to a PC. Internet Connects to the Ethernet switch, router or Internet. 3.
Green Register RED In use 3.4 Get Familiar with LCD LCD Name Date Time Phone Numbers Lines Softkey Function Softkey Buttons Description of function To display the current date. Date format is mm/dd To display the current time. Time format is mm:ss (A or P) To display the phone number of lines. To display the status of lines. The icon means unregistered. The icon mean registered. To display the current softkey function.
4 Menu User can use MENU, soft key and MUTE/DEL button to browse, modify and configure the phonebook, multi-functional keys, network, accounts, factory default and so on. 4.1 Items The table below lists Menu items which IP622C/IP622CWP included: Main menu Menu Items Submenu Items (LCD display) (LCD display) (LCD display) 1Phonebook 2 Multi-Functional Key(need password) 3Call History 4Text Message 5BlackList 6Preferences 7Ring Tone 1.1NewEntry 2.1Exp Key 1 2.2Exp Key 2 2.3Exp Key 3 2.
7.2Bell Type2 7.3Bell Type3 7.4Bell Type4 7.5Bell Type5 7.6Bell Type6 7.7Bell Type7 7.8Bell Type8 7.9Bell Type9 7.1Bell Type10 8Volume Setting 9Accounts (need password) 10Call Forward 11Time/Date 9.1Line 1 9.2Line 2 10.1CFWD All 10.2CFWD When Busy 10.3CFWD When No Answer 11.1Time(H:m:s) 11.2Date(m/d/y) Press up or down key to turn up or turn down volume. To enable/disable line1. To set password of line1. To set account of line1. To set display name of line1. To set the phone number of line1.
Product Info 15Status 13.6Secondary DNS 13.7Enable WAN Login 13.8Web Port 13.9SIP QoS 13.1RTP QoS 13.11Data QoS 13.12VLAN Tag 13.13VLANID 13.14802.1p Priority 14.1Product Name 14.2Software Version 14.3Hardware Version 14.4MAC Address 14.5Serial Number 15.1Intenet Port Status 15.2VPN Status 15.3Registration Status 16Reboot 17Factory Default 18Set Password 19LCD Contrast 20Login/Logout To view the secondary DNS, or to change the secondary DNS. To enable or disable user login webpage from Internet port.
8) Press the cancel softkey button to cancel changes and back to the up level. 9) The password which need when access to Accounts item is the same as the one of admin mode when login Web, default is admin.
5 Using Basic Phone Function 5.1 Using the Handset/ Speakerphone/ Headset 5.1.1 Using the Handset To place and answer calls using the handset, simply lift the handset. 5.1.2 Using the Speakerphone To place and answer calls using the speaker, press the speaker button. The green light behind the button will illuminate. 5.1.3 Using the Headset To place and answer calls using the speaker, press the headset button. The green light behind the button will illuminate. 5.2 Making Telephone Call 5.2.
5.2.3 Dialing from Phonebook Adding a phonebook Below are the steps to add a phonebook in menu, User can also add phonebooks from your PC using IP622C/IP622CWP Web Interface. Step 1.Press MENU button access to the menu items, and use the softkey button to choose 1.Phonebook Step 2.Add one phonebook according to the prompt, press the abc softkey button to change the input method between digit, capital letter and small letter.
5.2.6 Using Dial Plan Adding one dial plan: Step 1.Open Phone/Dial Plan webpage Step 2.Add one dial plan, user can refer to 7.7.3 Dial Plan Using dial plan to make call: Dial the phone number according to one dial plan. 5.2.7 Using Hot Line Add the hot line from SIP Account/Line1/2 webpage, Supplementary Service Subscription column, below is one example: Step 1.Open SIP Account/Account1/2 webpage, Supplementary Service Subscription column Step 2.
enable according to the prompt. Notice: user can also enable auto-answer in Phone/Preference webpage, miscellaneous column. 5.3 Adjusting Call Volume From menu: Step 1.Press Menu button, and then choose volume. Step 2.Press up and down button to turn up or turn down volume. Using multi-function key: Step 1.Choose two multi-function key (assuming the two multi-function keys are Exp Key 1 and Exp Key 2), and configure as following: Step 2.
From menu: Step 1.Press Menu button, and then choose 5black list. Step 2.Choose NewEntry, and then add one black list according to the prompt. From Webpage: Step 1.Login the web, open Phone/Phonebook webpage, Black List column. Step 2.Refer to the 7.6.4.1 Black List to add blacklist. 5.5 Muting a Call During an active call, pressing the MUTE/DEL button to mute the handset, headset or speakerphone.
Step 3.After the second person answers the call, press conf softkey button to start the conference call; all three parties will be participating in a conference call. Note: If you hang up firstly, the other two parties will be disconnected; if one party hangs up firstly, you can go on talking with the other party. 5.8 Attended Transfer You call the person to whom you are transferring the call and speak to them before transferring the call: Step 1.
From menu: Step 1.Press the MENU button. Step 2.Select 10Call Forward and choose one type of call forwarding. • CFWD All—Forwards all calls to a single number immediately when there is an incoming call. • CFWD When Busy—Forwards all calls to another number when the phone is busy. • CFWD When No Answer—Forwards calls to another number if there's no answer at your phone. Step 3.Enable the CFWD and fill in the call forwarding number. Step 4.Press the save softkey button to save changes. 5.
To end a headset call, press the headset button. 5.13 Viewing and Returning Missed Calls The LCD screen on your IP phone will notify you like the following picture if a call came in that was unanswered. To return a missed call: • If the LCD screens shows a missed call: Step 1.press the softkey button under miss to view the call. Step 2.Press the softkey button under dial to return the missed call. • If the LCD screen does not show a missed call, you can return a call from the Missed Call list: Step 1.
5.14 Text Message 5.14.1 Sending Message Step 1.Press Menu button, and then choose 4Text Message by using the up button or the down button. Step 2.Press the select softkey button to enter to 1SEND item. Step 3.Press the select softkey button to edit message. Note: When inputting text, use the abc softkey button to change the input method among numbers, capital and lowercase English letters, abc stands lower case, ABC stands capital letter, and 123 stands digit* Step 4.
Step 3.Press the select softkey button to access to the next item. Choose the message you want to read by using the up button or the down button.
6 Using Advanced Phone Functions 6.1 Speed Dial Creating Speed Dial: Following are the steps to creating speed dials in webpage; you can also creating it from LCD Menu. Step 1.Access to web, and then open Phone/Multi-Functional Key webpage Step 2.Then configures one Exp key to speed dial, and then choose the line and fill in the phone number. The following picture is a setting example: Step 3.Press button to save changes and then press button to make changes effective. Using Speed Dials: Step 1.
Step 4.Press the save softkey button to save the changes From Webpage: Step 1.Login Web, open SIP Account Line 1/2webpage, go to Supplementary Service Subscription column. Step 2.Enable MWI Enable and fill in the Voice Mailbox Numbers (get the number from your phone administrator), below is a settings example based on Asterisk. Step 3.Press button to save changes, then the notice will appear, press button to make changes effective. 6.2.
Step 1.Press the Menu button. Step 2.Select 7 Ring Tone. Step 3.Use the up and down buttons to highlight the ring tone. Press the select softkey button to choose the highlighted ring tone. 6.5 Setting Your Phone’s Date and Time The date and time for your phone normally come from the phone server. However, if you need to change some date and time parameters, you can follow these steps: Step 1.Press the Menu button, select 11Time/Date. Step 2.
Press Menu button and choose 17 Factory Reset, user is required to input the password, then a notice will appear, press the ok softkey button to continue. In menu: Press #*06# on the phone and select 4 Factory Reset, then there is a notice inform you to confirm the performance, enter yes(937), then phone will be factory default. Using Website: Step 1.Access to website, open Administration/Management webpage; Step 2.Press the factory default button at the bottom of the webpage; Step 3.
7 CONFIGURATION 7.1 Web-based Configuration This section will show you how to configure your IP622C/IP622CWP using the web-based configuration interface.
7.2 Login To access the phone through a web browser Step 1.Setup IP622C/IP622CWP correctly Step 2. You can press menu key -->15 status->Internet Port Status-->IP Address on the LCD screen. Step 3.Enter “http://Internet IP Address” in the address field of the browser. Step 4.Type “admin” or “user” for the User Name, and input the password click on the Login button to access the configuration page.
To cancel the changes.
7.4 Status 7.4.1 Basic This webpage displays the basic status of your IP622C/IP622CWP, including the information about product information, SIP account status, network status, VPN status, PC port status and system status. Click Refresh button to refresh the status.
7.4.2 Syslog This page displays the log of system. User can press Clear button to clear all information. Click Refresh button to refresh syslog. Click Save to save the system log to your local PC.
7.5 SIP Account 7.5.1 SIP Settings 7.5.1.1 SIP Parameters 7.5.1.2 NAT Traversal Webpage Field Name Description If or not enable NAT. IP622C/IP622CWP supports STUN traversal, NAT Traversal choose “STUN” in the “NAT Traversal Mode” if you want traverse NAT/Firewall. STUN Server IP STUN server IP address, default is stun.fwdnet.net NAT Refresh The interval to refresh Interval (sec) STUN Server STUN port Port 7.5.
Following is the description about that. 7.5.2.1 Basic Set the basic information provided by your VOIP Service Provider, such as Phone Number, Account, password, SIP Proxy and so on. Webpage Field Name Description Line Enable If or not enable Line1 If or not enable PEER to PEER If enable, Line1 will not send register request to SIP server; In System Status, SIP-1 Status is Registered; SIP-1 can make call out, but others can not call SIP-1.
Type3 Audio Codec Type4 Audio Codec Type5 G.723 Coding Speed Packet Cycle Silence Supp Enable Echo Cancel G.711A, G.722, G.729, G.723 Choose the audio codec type from G.711U, G.711A, G.722, G.729, G.723 Choose the audio codec type from G.711U, G.711A, G.722, G.729, G.723 Choose the speed of G.723 from 5.3kbps and 6.3kbps The RTP packet cycle time If or not enable silence If or not enable echo cancel,default is enable. 7.5.2.
Payload (>=96) Register Refresh Interval RTP Port Cancel Message Enable Prack Enable SIP OPTIONS Enable Keep-alive interval (10-60s) Anonymous Call Anonymous Call Block Proxy DNS Type Use OB Proxy In Dialog VPN Dial Prefix User Type Only Recv Request From Server Request-URI User Check Hold Method 7.5.3 The interval between two normal Register messages. You can use the default setting. Set the port to send RTP. IP Phone will select one idle port for RTP if you set “0”, otherwise use the value user set.
SIP/RTP/ Qos Default is 0, user can set from 0~63. 7.6 Network 7.6.1 Basic User can configure the parameters of Internet Port, PC port and Network Address Server Settings (DHCP). The details are as follows: 7.6.1.1 Internet Port (WAN) Static: In static mode, user should fill in the values of IP Address, Subnet Mask, Default Gateway, Primary DNS and Second DNS got from your administrator.
Primary DNS Second DNS The primary DNS of Internet port. The second DNS of Internet port. DHCP: In DHCP mode, IP phone is a DHCP client. IP phone will get the IP Address, Subnet Mask and Default Gateway from the DHCP server. Webpage Field Name Internet DNS Mode Primary DNS Secondary DNS DHCP Renew DHCP Vendor Description Choose Automatic Configuration-DHCP. Choose DNS type from Manual and Automatic ◆In Manual: user should set the Primary DNS and Second DNS manually.
PPPoE: Webpage Field Name Internet DNS Mode Primary DNS Secondary DNS PPPoE Account PPPoE Password Confirm Password Operation Mode Description Choose PPPoE. Choose DNS type from Manual and Automatic ◆In Manual: user should set the Primary DNS and Second DNS manually. ◆In Automatic: IP Phone will get the Primary DNS and Second DNS from DHCP Server automatically. The primary DNS of Internet port. The secondary DNS of Internet port.
7.6.1.2 PC Port (LAN) Webpage Field Name Description Local IP address Local Subnet Mask Local DHCP server DHCP Start Address DHCP End Address Set the IP address of PC port. Efficient when user choose NAT. Set the subnet mask of PC port. Efficient when user choose NAT. DNS Mode Primary DNS Secondary DNS Client Lease Time (0-86400s) DNS Proxy 7.6.2 If or not enable DHCP server. This is the start IP address assigned by the DHCP server. This is the end IP address assigned by the DHCP server.
You can login IP622C/IP622CWP’s Web via PC port if you are incautious to make it wrong. And then cloning the right MAC or resume the default settings. Step 1 Press button to get the PC’s MAC address Step 2 Press 7.6.3 to save the changes Step 3. Press to cancel MAC address clone. Step 4. Press to reboot IP622C/IP622CWP. Wireless(Only for IP622CWP) Page Field Name Description Connection Status Show the current connect status.
Password 7.6.4 Input the password of the device you need to connect. VPN A Virtual Private Network (VPN) is the extension of a private network that encompasses links across shared or public networks like the Internet. In short, by VPN technology, you can send data between two computers across a shared or public network in a manner that emulates the properties of a point-to-point private link. Webpage Field Name VPN Enable Initial Service IP User Name Password 7.6.5 Description If or not enable VPN.
Webpage 7.6.6 Field Name Description DMZ Enable DMZ Host IP Address If or not enable DMZ Field Name Description DDNS Webpage Dynamic Provider 7.6.7 Set the IP address of DMZ host DNS Select the DDNS provider. Account Enter the account user gets from the DDNS provider. Password Enter the password user gets from the DDNS provider. DDNS Enter the DDNS domain. Status Display the DDNS status. Multi WAN Webpage Field Name Description Index Index Name The name of service mode.
tag 7.7 Phone User can configuration volume, call forward, multi-functional key, dial plan, phonebook and call log. 7.7.1 Preference User can configure the value of ring volume, speakerphone volume, handset volume and so on. 7.7.1.1 Preference Webpage Field Name Handset Input Gain Handset Volume Gain Speakerphone Input Gain Speaker Volume Ringer Volume Speakerphone Mic Boost Description Adjust the handset input gain from 0-7. Adjust the output gain from 0-7.
Warning Tone Ring Back Tone Call Waiting Tone Min Jitter Delay (ms) Max Jitter Delay (ms) Ringing Time(Sec) Ring back tone Call Waiting tone. The Min value of IP622C/IP622CWP’s jitter delay, IP622C/IP622CWP’s jitter is an adaptive jitter mechanism. The Max value of IP622C/IP622CWP’s jitter delay, IP622C/IP622CWP’s jitter is an adaptive jitter mechanism. How long IP622C/IP622CWP will ring 7.7.1.
7.7.1.4 Miscellaneous Webpage Field Name Description Auto Answer If or not enable auto answer. If enable, IP622C/IP622CWP will auto answer all incoming call immediately. Auto Answer by CallINFO Dial Time Out Call Immediately Key Auto Hookon Mode ICMP Ping Escaped char enable 7.7.2 If or not enable auto answer by call info. How long IP622C/IP622CWP to sound dial out tone when IP622C/IP622CWP dialing number. Choose call immediately key form * or #.
Adding speed dial: Step 1.Choose one Exp Key to configuration Step 2.Select the speed dial from the drop down list Step 3.Choose the Line from auto (the first line registered), line1, line2 Step 4.Fill the phone number in Expansion Step 5.Press Step 6.Press to save changes button to make changes effective. If set properly, press the corresponding key to make call immediately Adding shortcut key: Step 1.Choose one Exp Key to configuration Step 2.Select the shortcut key from the drop down list Step 3.
7.7.3 Dial Plan 7.7.3.1 Parameters and Settings Webpage Field Name Dial Plan Line Description If or not enable dial plan. Choose the call mode from line1, line2. Fill in the sequence used to match input number Digit Map Action Move Up Picture 1 Move Down The syntactic, please refer to the following Dial Plan Syntactic Choose the dial plan mode from Deny and Dial Out. Deny means IP622C/IP622CWP will reject the matched number, while Dial Out means IP622C/IP622CWP allow dial out the matched number.
Steps : Adding one dial plan: Step 1. Enable Dial Plan Step 2. Click Add button, and the configuration table like Picture 1 will appear Step 3. Fill in the value of parameters. Step 4.Press OK button to end configuration. Step 5. Press Save Settings button to save changes. Editing one dial plan: Step 1. Enable Dial plan Step 2. Choose one dial plan Step 3. Click Edit button, and the configuration table like Picture 2 will appear Step 4. Change the value of parameters. Picture 2 Step 5.
7.7.3.2 Dial Plan Syntactic No. String 1 0123456789 *# Legal characters 2 X Lowercase letter x stands for one legal character [sequence] To match one character form sequence. For example: • [0-9]: match one digit form 0 to 9 • [23-5*]: match one character from 2 or 3 or 4 or 5 or * 4 x. Match to , , , …... For example: “01.”: can match ”0”, “01”, “011”, ”0111”, …….., ”01111…” 5 Replace dialed with substituted.
7.7.3.3 Example 1. Example 1 Using line 1, if user dials #12#2, IP622C/IP622CWP will call 010#12%232 immediately. 2. Example 2 Using line 2, if user dials 5,8101, IP622C/IP622CWP will call 2413338101 immediately, And IP622C/IP622CWP will make outside dial tone after inputting “5”, stop tone until inputting “8”. 3. Example 3 Using line 1, if user dials 422xxxx or 522xxxx, IP622C/IP622CWP will call 22xxxx333 immediately. 4.
will reject the phone number out. 7.7.4 Phone Book 7.7.4.1 Upload &&Download Phonebook or Blacklist Webpage Field Name Description Click Phonebook Upload&&Dow nload to save the phonebook to the local PC. Click to select the phonebook and click to upload it to the phone. Click Blacklist Upload &&Download to save the blacklist to the local PC. Click to select the blacklist and click to upload it to the phone. 7.7.4.2 Phonebook Webpage Picture 1 Field Name Description Name Input the name.
Steps : Adding one phone book: Step 1. Click Add button, and the configuration table like Picture 1 will appear Step 2. Fill in the value of parameters. Step 3. Press OK button to end configuration. Step 4. Press Save button to save changes. Picture 2 Editing one phone book: Step 1. Choose one phone book Step 2. Click Edit button, and the configuration table like Picture 3 Picture 3 will appear. Step 3. Change the value of parameters. Step 4. Press OK button to end configuration. Step 5.
Step 2. Click Move to blacklist button to delete the phone book 7.7.4.3 Black List Webpage Picture 1 Field Name Description Name Input the name Number Input the phone number Steps : Adding one Black List: Step 1. Click Add button, then the configuration table like Picture 1 will appear Step 2. Fill in the value of parameters. Step 3. Press OK button to end configuration. Step 4. Press Save button to save changes. Picture 2 Editing one Black List: Step 1. Choose one black list Step 2.
7.7.5.1 Redial List 7.7.5.
7.7.5.3 Missed Call 7.8 Administration Use can manage the IP622C/IP622CWP in these six webpages; you can configure the Time/Date, password, web access, system log and so on. 7.8.1 Management You can configuration the value of Time/Date, password, web access, and system log and so on. 7.8.1.1 File Upload&&Download Webpage Field Name Config File Upload&& Download Web Logo File Upload Description Upload or Download the configuration file. Upload the web log file.
7.8.1.2 Administrator Settings Webpage Field Name User Type Description Select Admin User or Normal User. New User Name Input the user name. New Password Input the password. Confirm Password Language VPN Access Remote Web Login Web Port Web Idle Timeout(0-60m) Input the password again. User can select the language, options are English,Russian, Finnish, Spanish,Czech, Hebrew and Romania. Enable or disable access VPN If or not enable remote web login.
Start Day of Week Start Day of Week Last in Month Start Hour of Day Stop Month Stop Day of Week Stop Day of Week Last in Month Stop Hour of Day Choose starting day Choose starting week Choose starting hour Choose stopping month Choose stopping day Choose stopping week Choose stopping the function hour Steps: Daylight Saving Time: Step 1. Enable Daylight Saving Time. Step 2.
Webpage Field Name Description SysLog Enable If or not enable system log. Choose log level from INFO and Debug. Debug provides more system log information than INFO. If or not enable remote system log, Fill in remote system log server address. Syslog Level Remote Syslog Enable Remote Syslog Server 7.8.1.5 Packet Trace Webpage Field Name Description User can use this function to trace the packets sent by the phone.
7.8.2 Firmware Upgrade Webpage Description Steps: Step 1. Press to browser the upgrade file. Step 2. Press to start upgrading, LCD will display the notice when upgrading. Step 3. Login web and then check the firmware whether well upgraded by viewing the firmware version in Status/Basic webpage. 7.8.3 Provision 1) Provisioning allow IP622C/IP622CWP auto-upgrading or auto-configuring 2) IP622C/IP622CWP supports 3 ways to provision: TFTP, HTTP and HTTPS.
Resync Periodic(sec) Resync Error Retry Delay Forced Resync Delay Resync After Upgrade Option 66 Option 67 Config File Name Profile Rule Upgrade Enable Upgrade Error Retry Delay Upgrade Rule 7.8.
Password The TR069 server’s password for connecting to IP622C/IP622CWP 8 Trouble Shooting This section provides solutions to problems that can occur during the installation and operation of the IP phone. Read the following descriptions if you are having problems. 8.1 No Operation after Power On Solution: Check if the power adapter is properly connected. If applicable, check if the PoE (Power over Ethernet) switch behind the IP phone is set correctly. 8.
8.5 Can not Receive Any Phone Call Solution: Check the status of your SIP registration status, or contact your administrator, supplier, or ITSP for more information or assistance. 8.6 No Voice during an Active Call Solution: Check if the servers support the current audio codec type, or contact your administrator, supplier, or ITSP for more information or assistance. 8.7 Can not connect to the configuration Website Solution: Check if the Ethernet cable is properly connected.
Solution: Factory default: press Menu button and choose 16Factory Default, then a notice will appear, choose OK by using the corresponding softkey button. And this way is required password,too. There is another way to make factory default, press #*06# on the phone's panel, and then select 4 Factory Reset, input YES(937) to confirm your action, and then the phone will reset all the settings.
-- Consult the dealer or an experienced radio/TV technician for help. RF Exposure Statement To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.
9 Contact ways Sales: sales@flyingvoice.com Support: support@flyingvoice.com MSN:e3call@hotmail.com Skype:flyingvoice_sales Shenzhen Add: Room102, 1F East, Bldg 3#, Minqi Park, Pingshan, Xili, Nanshan Districe, Shenzhen, China Tel: +86-755-26099365 Fax: +86-755-26099347 Beijing Add: C-1603, Caizhi International Bldg, No.