F LY E R T M C R U I S E R O W N E R ’ S M A N U A L
Welcome to the Flyer™ Fleet Congratulations on your new Flyer™ Cruiser! The Flyer™ line delivers a high-performance experience for riders of all ages, ranging from micromobility solutions for families to premium wheels for kids. As an extension of the Radio Flyer® brand, Flyer™ products are created with the same beautiful design and quality that has inspired our work for over a century. We hope your new Flyer™ Cruiser offers a fun, sustainable, and convenient way to get out and explore your world.
TA B L E O F C O N T E N T S Important Safety Instructions 7 Getting Started 8 Assembly Instructions Accessories 16 Adjusting Bike Fit 17 Operating Instructions 4 8 20 Handlebar Display 20 Flyer™ Smartphone App 22 Flight SpeedTM Battery 23 Motor Control 27 Riding & Safe Operating Guidelines 28 Ride Safety Checklist 28 Maintenance 30 Moving and Storage 31 Troubleshooting 32 Warranty 34 5
Important Safety Instructions S A F E T Y WA R N I N G S WARNING! When using this product, basic precautions should always be followed including the following: • Read all safety warnings and instructions before using the product. Failure to follow warnings and instructions may result in serious injury or death. • To reduce the risk of injury, close supervision is necessary when the product is near children. • Do not put fingers or hands near spokes or moving parts.
Getting Started Step 2: Install kickstand A. Remove the kickstand bolt and washers using the provided 8mm allen wrench. A S S E M B LY I N S T R U C T I O N S Set aside. The following steps provide a general overview of the assembly B. Align the kickstand with the mounting plate located near the rear fender. Ensure the kickstand is oriented in the correct direction, as shown in image B below. process for your eBike.
Step 3: Install handlebar stem Step 4: Install the front logo plate Your Flyer™ eBike’s handlebar stem is designed to be adjusted for optimal comfort. A. Remove the screws and washers using the 3mm allen wrench and set aside. A. Remove the protective cover from the handlebar stem and discard. B. Align the wire harness, rear brake cable, and shifter cable between the threaded posts on the headtube. Route the front brake cable to the side of the threaded posts B.
Step 5: Install the front wheel Step 6: Install the front fender The bike is shipped with a steel spacer installed in the fork dropouts to prevent damage A. Remove the screw and washers at the top of the fork using the provided 3mm allen during shipment. Prior to installing the front wheel, this spacer must be removed by first disassembling with the 18mm wrench and can be discarded. A. Remove the nuts and washers from the front axle and set aside. B.
Step 7: Install headlight Step 8: Install pedals A. Fully install the connector to the rear of the headlight housing ensuring the terminals are properly aligned A. Identify the right and left pedals before assembling. The right pedal will have a B. Using the provided 3mm allen wrench, remove the screw and washers from the front of the fork. Set aside. B. Install washers onto each pedal before installing. C.
A D J U S T I N G S E AT H E I G H T Step 9: Check fastener torque values Area of Bike Hardware Torque (Nm) Handlebar Stem Clamp Bolts 18 Stem Expansion Bolt 20 Brake Lever Clamp Bolts 7.5 Seat Post Saddle Mounting Bolts 10 Kickstand Kickstand Bolt 25 Front/Rear Brakes Disc Brake Rotor to Hub 8 Caliper Adapter to Frame 13 Caliper to Adapter 13 seat post beyond the minimum insertion marking on the seat post tube. If the seat post is not Fender Connection Screw 7.
ADJUSTING HANDLEBAR STEM HEIGHT A D J U S T I N G H A N D L E B A R R O TAT I O N A L P O S I T I O N Following assembly of the bike, the handlebar stem height can be adjusted to fit the The rotational positon of the handlebar can also be adjusted to fit the individual rider. individual rider. Ensuring that the handgrips and brake levers are in the correct position will avoid any A. R emove the rubber cap. Using the provided 6mm allen key, loosen the stem bolt. B.
Operating Instructions H A N D L E B A R D I S P L AY Display Controls Location Operating Instructions PAS Increase Button Tap to increase pedal assist level 2 Headlight Power Button Tap to turn headlight on/off 3 Power Button Push and hold to turn display on/off 4 PAS Decrease Button Tap to decrease pedal assist level Push and hold to enable t mode 6 5 1 Description 1 Display Icons MPH 2 3 km/h PAS E F Location Description 5 Speedometer 6 Pedal Assist Level 7 Headlight Status
F LY E R ™ A P P U S A G E Charging the Battery In order to download the Flyer™ app for your Flyer™ Folding Cargo, scan the QR codes below or search “Flyer TM” in the App Store or Google Play Store. Power on the eBike and ensure your mobile device has Bluetooth turned on. Click The Flight SpeedTM battery can be charged while installed in the bike or when removed from the bike frame. A. E nsure the battery is off by powering off the display as described in the “Handlebar Display” section above.
Removing the Battery Install Bluetooth Tag (optional) Note: The battery should only be removed when the bike is stationary and powered off. The bike includes a holder that can house one Bluetooth location tag as a security Failure to do so could result in damage to the battery or electrical system of the bike. feature. The tag must be purchased separately and activated prior to installation. A. I nsert the provided key into the battery lock.
Checking Battery Charge Level MOTOR CONTROL In addition to the main display, the battery charge level can also be checked directly on the battery. A. R emove the battery following the steps outlined in the “Removing the Battery” section. Pedal Assist System (PAS) The pedal assist system (PAS) augments your natural pedaling action by providing an additional boost from the motor. Using the “+” and “-“ buttons on the display, you can control the level of assistance provided by the motor.
Riding & Safe Operating Guidelines Seat • Ensure the seat is securely connected to the eBike and the seat cannot be moved. • Confirm the adjustment lever is fully tightened and locked. • Verify the seat is properly adjusted to fit your height. • Confirm that the seat is securely fastened to the post (torque: 10 Nm). Handlebar • Confirm the handlebar always aligns with fork when moving in desired direction and both parts turn in unison.
Maintenance Always have a certified and reputable bike mechanic complete a tune-up on your eBike after your first 50-100mi. Regular tune-ups and inspections are critical to ensuring your bike stays in safe condition. For more information on recommended maintenance intervals please visit: Moving and Storing • Always remove the battery from the eBike before transporting the bicycle on a vehicle bike rack. • It is recommended to park the eBike indoors. • Store the battery in a dry location.
Troubleshooting Issue The eBike does not work or appear to turn on The eBike feels slow to accelerate and will not reach top speed The eBike’s range is reduced The battery does not charge The eBike is making an odd noise when moving 32 Possible Reason Corrective Action The battery has been fully drained Recharge the battery using the manufacturer provided charger The battery is not fully seated or installed into its dock Remove the battery from the eBike; reinsert the battery and fully seat it i
How do I make a warranty claim? Warranty RADIO FLYER INC. WILL NOT REPLACE ANY COVERED COMPONENT UNDER THIS LIMITED WARRANTY WITHOUT FIRST SEEING PHOTOS OR VIDEO OF THE DAMAGED COVERED COMPONENT.
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR PURPOSE. F L I G H T S P E E D ™ B AT T E R Y Battery and Charger Safety Warnings IN NO EVENT SHALL RADIO FLYER INC.
• To reduce the risk of fire, connect only to a circuit provided with 15 amperes maximum branch circuit overcurrent protection in accordance with the National Electrical Code, ANSI/NFPA 70. • When charging is complete, disconnect the charger from the wall outlet and the battery. • Place the battery and charger in a place out of reach from children. • To increase battery life, recharge after every use. • To maintain battery life, you must charge every 6 months.