USER MANUAL WTH600 - WIRELESS WEATHER STATION WITH WIRELESS TRANSMITTER SENSOR 1. INTRODUCTION Thank you for selecting the Extech WTH600 Wireless Weather Station with 5-in-1 wireless sensor. The sensor includes a self-emptying rain collector for measuring rainfall, an anemometer for wind velocity, a wind vane for wind direction, a temperature sensor, and a relative humidity sensor. The WTH600 comes fully assembled and calibrated for convenience. The sensor transmits data up to 492 ft.
CONTENTS 1. INTRODUCTION 1 2. PHYSICAL DESCRIPTIONS 3 3. DISPLAY DESCRIPTIONS 5 4. SENSOR INSTALLATION, BATTERIES, MOUNTING 7 5. MAIN UNIT OPERATION, BATTERIES, MOUNTING 9 6. WEATHER FORECAST 11 7. BAROMETRIC / ATMOSPHERIC PRESSURE 11 8. RAINFALL 12 9. WIND SPEED / DIRECTION 12 10. BEAUFORT SCALE 13 11. WIND CHILL / HEAT INDEX / DEW POINT 14 12. HISTORICAL DATA (PRIOR 24 HOURS) 15 13. MAXIMUM / MINIMUM MEMORY 15 14. HI / LO WEATHER ALERT 15 15.
2. PHYSICAL DESCRIPTIONS Main unit 1. SNOOZE / LIGHT button 2. HISTORY button 3. MAX/MIN button 4. RAINFALL button 5. BARO button 6. WIND button 7. INDEX button 8. CLOCK button 9. ALARM button 10. ALERT button 11. DOWN button 12. UP button 13. °C/°F slide switch 14. RCC button 15. SCAN button 16. RESET button 17. Battery compartment 18. Alert LED indicator 19. LCD display with backlight 20. Table stand Wireless Sensor 1. Rain collector 2. Balance indicator 3. Antenna 4. Wind cups 5. Mounting pole 6.
Rain gauge 1. Rain collector 2. Tipping bucket 3. Rain sensor 4. Drain holes Temperature and humidity sensor 1. Radiation shield 2. Sensor casing Wind sensor 1. Wind cups (anemometer) 2. Wind vane (direction) 4 WTH600-en-US_v1.
3. DISPLAY DESCRIPTIONS Main Display 2 3 4 5 6 7 8 1 9 10 11 1. Max/Min/Previous indicator 2. Low battery indicator for main unit 3. Time 4. Ice pre-alert on 5. RC Signal strength indicator 6. DST icon 7. Moon phase 8. Day of the week 9. Alarm icon 10. Date 11. Month Indoor Temperature/Humidity Display 2 3 4 5 1 1. Comfort/cold/hot icon 2. Indoor indicator 3. Indoor humidity 4. Hi / Lo Alert and Alarm 5. Indoor temperature 5 WTH600-en-US_v1.
Outdoor Temperature/Humidity Display 2 3 4 5 1 6 1. Outdoor signal strength indicator 2. Outdoor indicator 3. Outdoor humidity 4. Hi / Lo Alert and Alarm 5. Outdoor temperature 6. Low battery indicator for sensor 12+ Hour Forecast Display 1 1. Weather forecast indicator 2. Weather forecast icon 2 Barometer Display 1. Barometer indicator 2. Histogram 3. Absolute/Relative indicator 4. Barometer units (hPa / inHg / mmHg) 5. Barometer reading 6.
Wind Direction/Wind speed 1. Wind direction indicator 2. Wind direction indicator(s) during last hour 3. Current wind direction indicator 4. Wind speed indicator 5. Wind levels and indicator 6. Beaufort scale reading 7. Current wind direction reading 8. Average/Gust wind indicator 9. Wind speed units (mph, m/s, km/h, knots) 10. Hi Alert and Alarm 1 2 7 3 4 8 5 9 10 6 Wind Chill/ Heat index/ Indoor Dew point 1. Wind chill/ Heat index/ Indoor dew point indicator 2.
Install the wireless sensor in an open location with no obstructions above and around the sensor for accurate rain and wind measurement. Install the sensor with the smaller end facing to the North (proper orientation of the wind direction vane). Secure the mounting stand and bracket (included) to a post or pole, and allow a minimum distance of 1.5m off the ground. Points to NORTH 1.5 meter off the ground Mounting guidelines 1. Install the wireless sensor at least 1.
5. MAIN UNIT OPERATION, BATTERIES, MOUNTING Battery Installation and Mounting The WTH600 can be placed on a desktop or can be wall mounted for easy viewing. 1. Remove the battery door of the main unit. 2. Insert three ‘AA’ batteries according to the “+/-” polarity marks on the battery compartment. 3. Replace the battery door. 4. Once the batteries are inserted all of the LCD segments will be shown briefly before entering the radio-controlled time reception mode. 5.
2. Always place the unit away from interfering sources such as TV monitors, computers, etc. 3. Avoid placing the unit on or next to metal plates. 4. Enclosed areas such as airports, basements, or factories are not recommended. Setting the Date and Time The unit automatically sets itself accordingly to the Radio Controlled Clock signal it receives. To set the clock/calendar manually, first disable the reception by holding the RCC button for 8 seconds. Manually Setting the Clock and Time Zone 1.
Set the Alarm Clock 1. Press and hold [ALARM] for 2 seconds to enter alarm setting mode. HOUR will begin to flash. 2. Use [UP]/[DOWN] buttons to adjust HOUR, and press [ALARM] button to proceed to MINUTE. 3. Repeat step 2 above to set MINUTE, then press [ALARM] button to exit. Note: Pressing the [ALARM] button twice when alarm time is displayed will activate the temperature-adjusted pre-alarm (alarm will sound 30 minutes earlier if it detects outside temperature is below 26°F (-3°C)). 6.
3. The built-in barometer detects the environmental absolute atmospheric pressure changes. Based on the data collected, it can predict weather conditions for the next 12 hours. The weather indicators will change according to the detected absolute atmospheric pressure after 1 hour. 4. The relative atmospheric pressure is based on the sea level, but it will change with the absolute atmospheric pressure changes after operating the clock for 1 hour. Select the Measurement Units for the Barometer 1.
Select the Wind Display mode Press [WIND] button to toggle between: • AVERAGE The AVERAGE wind speed will display the average of all wind speed numbers recorded in the previous 30 seconds • GUST The GUST wind speed will display the highest wind speed recorded from last reading The wind level provides a quick reference and is indicated by a series of text icons: Level LIGHT MODERATE STRONG STORM Speed 2-8 mph 3-13 km/h 9-25 mph 14-41 km/h 26-54 mph 42-87 km/h ≥ 55 mph ≥ 88 km/h Select Wind Speed U
6 Strong breeze 7 High wind 8 Gale 9 Strong gale 10 Storm 11 Violent storm 12 Hurricane force 39–49 km/h 25–30 mph 22–27 knots 10.8–13.8 m/s 50–61 km/h 31–38 mph 28–33 knots 13.9–17.1 m/s 62–74 km/h 39–46 mph 34–40 knots 17.2–20.7 m/s 75–88 km/h 47–54 mph 41–47 knots 20.8–24.4 m/s 89–102 km/h 55–63 mph 48–55 knots 24.5–28.4 m/s 103–117 km/h 64–73 mph 56–63 knots 28.5–32.6 m/s ≥ 118 km/h ≥ 74 mph ≥ 64 knots ≥ 32.7m/s Large branches in motion. Whistling heard in overhead wires.
View Dew point (Indoor) Press the [INDEX] button repeatedly until DEWPOINT appears. Note: The dew point is the temperature below which the water vapor in air, at a constant barometric pressure, condenses into liquid water at the same rate at which it evaporates. ‘Dew’ is the term used to describe the condensed water that forms on a solid surface. The dew point temperature is calculated from the indoor temperature/humidity measured at the Main Unit. 12.
Set the HI / LO alert 1. Press the [ALERT] button to select the desired display field. 2. Use [UP] / [DOWN] buttons to adjust the settings. 3. Press [ALERT] button to confirm and continue to the next setting. Enable/disable the HI / LO Alarm Alert 1. Press the [ALERT] button to select the desired display field. 2. Use [ALARM] to turn the alert on or off. 3. Press [ALERT] to continue to the next setting. Note: 1. The unit will automatically exit setting mode in 5 seconds if no button is pressed. 2.
Too cold Comfortable Too hot Note: 1. Comfort indication can vary at the same temperature, depending on the humidity. 2. There is no comfort Indication when temperature is below 32°F (0°C) or above 140°F (60°C). 17. CLEARING STRAY READINGS During installation of the wireless sensor, the sensors are typically triggered which results in erroneous rainfall and wind measurements.
Northern hemisphere: New Moon Full Moon Waxing Crescent Waning Gibbous First quarter Third quarter Waxing Gibbous Waning Crescent Southern hemisphere: New Moon Full Moon Waxing crescent Waning Gibbous First quarter Third quarter Waxing Gibbous Waning Crescent 20. CLEANING Cleaning the Rain Collector 1. Rotate the rain collector 30° counter-clockwise. 2. Gently remove the rain collector. 3. Clean and remove debris. 4. Allow components to dry before re-assembly.
22. PRECAUTIONS • • • • • • • • • • • • Please observe all warnings and follow all instructions. Do not subject the unit to excessive force, shock, dust, temperature or humidity. Do not obstruct the ventilation holes. Do not immerse in water. If the unit gets wet, dry it immediately with a soft, lint-free cloth. Do not clean the unit with abrasive or corrosive materials. Do not tamper with the unit’s internal components. This invalidates the warranty. Use new batteries only.
24. SPECIFICATIONS MAIN UNIT Dimensions (W x H x D) Weight Battery power Sensor displays INDOOR BAROMETER Barometer units Measuring Range Resolution Accuracy@ 32~122°F (0~50°C) 4.7 x 7.5 x 0.9” (120 x 190 x 22 mm) 13.1 oz. (370g) with batteries 3 x AA size 1.5V batteries (Alkaline recommended) Wind speed, Wind direction, Rain gauge, Temp., RH hPa, inHg and mmHg 540~1100 hPa; 405~825 mmHg; 15.95~32.48 inHg 1hPa, 0.01inHg, 0.
OUTDOOR TEMPERATURE Temp. units °F or °C Display range -40°F to 176°F (-40°C to 80°C) Operating range -40°F to 140°F (-40°C to 60°C) Resolution 0.1°F or 0.1°C Accuracy +/- 1°F or 0.
25. Warranty FLIR Systems, Inc. warrants this Extech Instruments brand device to be free of defects in parts and workmanship for one year from date of shipment (a six month limited warranty applies to sensors and cables). If it should become necessary to return the instrument for service during or beyond the warranty period, contact the Customer Service Department for authorization. Visit the website www.extech.com for contact information.
Garantie FLIR Systems, Inc. garantit que cet appareil Extech Instruments est exempt de défauts matériaux et de fabrication pendant un an à partir de la date d’envoi (une garantie limitée de six mois s’applique aux capteurs et aux câbles). Si le renvoi de l’appareil pour réparation devient nécessaire durant ou après la période de garantie, contactez le service client pour autorisation. Pour obtenir les coordonnées, visitez le site Web suivant : www.extech.com.
Garantía FLIR Systems, Inc., garantiza este dispositivo marca Extech Instruments para estar libre de defectos en partes o mano de obra durante un año a partir de la fecha de embarque (se aplica una garantía limitada de seis meses para cables y sensores). Si fuera necesario regresar el instrumento para servicio durante o después del periodo de garantía, llame al Departamento de Servicio a Clientes para obtener autorización. Visite www.extech.com para Información de contacto.