Indirect Measurement Determining a Distance Using 3 Measurements (See Figure I") Press this button € twice; the display shows the following symbol, the display < shows. The distance to be measured flashes in the symbol. 7% Aim at the lower point (1) and trigger the measurement. After the first measurement the value is adopted. Keep the instrument as horizontal as possible. 7% Pres ta measurement the distance result of the horizontal point (2).
Directive Reagent Determining & Distance Using 3 Measurements (Figure's 17) Press this button three times; the display shows the following symbol, the display 2] shows, The distance to be measured flashes In the symbol. 3 veep Instrument as horizontal as possible, am at the point (1) and wiggler the measurement. €E3 Press to measurement the distance result of the middle point (2). C3 Press to measurement the distance result of the upper point (3).
Timer (sat triggering] € Pres. button to sat 3 5-second time delay. or €3 Crass and hold down this button until the desired time delay Is reached (max. 60 seconds). Or you can use button to change time delay. Press this button, remaining seconds until measurement (e.g. 59, 58, are displayed In a countdown. The last 2 seconds will flash and beep faster. After the last beep the measurement is taken and the value is displayed.
Stake out function (Prefigures K7} Two different distances (a and b) can bs sneered Into the Instrument and can then be used b> mark off defined measured lengths, e.g. In the construction of wooden frames. Ef rings stoke out distances: s button longer and the stake out function symbol appears in mie display The value (a) and the corresponding intermediate line flash. Bystander £3 + You can adjust the values (first a and then b} to suit the dies ort distances.
‘The function can be stopped any time by pressing 3 £73 the button. Tilt measurement (See"Figure 17} “The inclination sensor measures tits between == 65". During tilt measurement the instrument should be hold without a transverse tif (+ 107). Press this button once to activate the til sensor. Tha symbol appears in the display. Tha tit value is displayed in the intermediate line 1. Press to measure the Indignation and the distance.
Technical Dedications Range {use target plate from about 50m) ‘Measuring accuracy up & 10m 0, standard deviation) Measuring units Laser Class Laser Type Smallest unit displayed TI measurements: Tilt sensor: Measuring range Accuracy(2 o, standard deviation) ~to laser beam to the housing Area, Volume Calculations indirect measurement using Pythagoras Woodlot: TOM-150 0.
Indirect measurement ung Tt senior (direct horizontal distance) “Angle measurement using OF sensor(z 65 Addition Subtraction Continuous Measurement Miry Max Distance Tracking Timer (set-triggering) Laser continuous Stake out function Display illumination display ‘Functionalism end piece Tripod thread Beep indication BLUETOOTH® 3.
Dust Protect Splash proof P54 History measurement records 20 Keyboard Type Super Soft-Touch (Long life) prating Temperature O°C to 40°C2°F 10 104) Storage Temperature “TOC to GOAT to 140°) Batteries Type Battery Le Up to 8,000 measurements Hutton laser switch-off after 30 seconds “Ato Instrument switch-off after 3 min Dimension 135% 53 230 mm Weight 605 * Use a target plate to Increase the measurement range during daylight or If the target has poor reflection **in favorable conditions {good target surface p
7.Troubleshooting — Causes and Corrective Measures Code Cause Corrective measure 204 Calculation error Repeat procedure 208 Received signal toa weak, Use target plate measurement time too long. Distance >50m 205 Received signal £00 strong Target too reflective target plate) 252 Temperature too high Cool down instrument 253 Temperature too low Warm up Instrument 255 Hardware error Switch Goff the device several Gms, If the symbol stl appears, please contact your dealer for assistance.
Measuring Range The range is limited to 70m. At night or dusk and if the target is in shadow the measuring range without target plate is increased. Use a target plate to Increase the measurement range during daylight or If the target has poor reflection properties. Target Surfaces Measuring errors can occur when measuring toward colorless liquids (e.g. water) or cht free gla, Styrofoam o similar semipermeable surfaces, Laming at high gloss surfaces may deflect the laser beam and lead to measurement errors.
FCC Statement: ‘This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1} this device may not cause harmful interference, and (2) this devise must accept any interference received, including Interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.