USER MANUAL
1 Power Mute TV Channel down Channel up Volume down Volume up TV button STB button Delete button Add button
2 Thank you for your purchase! We will guide you step by step to sync Flipper with your devices. But first, some preliminaries: Code updates, Video tutorials and FAQs Online: FlipperRemote.com/Support Email: Support@FlipperRemote.com Telephone support also available online. Start with your devices ON. Slide down the bottom half of Flipper to reveal the 0-9 and setup buttons. See code list for codes listed by Brand of your device. Common Codes (see code list for others, and updates online, FlipperRemote.
3 INDEX Flipper can work with a TV Only or a STB (STB is set top box = cable box). Flipper has three set up methods: Code Entry, Code Search and Learning. 1. 2. 3. 4. Code Entry: a. TV Only..................................................... 4 b. TV and STB............................................. 5 c. Soundbars................................................ 7 On / Off options:.......................................... 7 Code Search:.................................................. 8 Learning:....
4 TV ONLY Check that you do not have a STB / cable box. Many facilities install their boxes attached to the TV or on a wall. If you see a STB, go to TV and STB. 1. TV Only mode: press and hold TV till light solid, then 970; light flashes off; 2. Test the preset: press Vol and CH. If working, go to Favs. If not working: 3. Locate your brand TV in the code list, then: a. press and hold TV till light solid, then enter the code. Light turns off. Test CH and VOL. If working go to Favs.
5 TV AND STB INSTALLATIONS Flipper is preset to many devices. First we test the preset. 1. Set TV: press VOL to test preset. If working, go to STB. If not: a. Press and hold TV till light turns solid, then enter the code for your brand - test VOL; If it doesn’t work, then try next code; If no codes work, go to Code Search. 2. Set STB: press CH to test preset. If working, go to Favs. If not, then: a.
6 In some boxes, LC will trigger a Menu. If it does, do not use LC; In other boxes, LC will trigger a Menu only in 4 digit channels. If so, then use LC for all but 4 digit channels. 1. Program Favs: Press and hold STB and ADD at same time till light turns solid; 2. Add channels: (Try two to test): a. Channel entry format: 7-LC-ADD; 44-LC-ADD; for channels 7, 44; 3. Exit: Press and release the STB button to exit, test; Let the channel change before pressing CH again; a.
7 On/Off Options: Flipper is preset to turn on and off the TV and STB by default. Occasionally, a user may experience one device on while the other is off. To Modify so only TV turns on and off: TV Only: Press and hold ADD till light turns solid, then enter 999. Then turn off any standby or power saver in the box. TV and STB: Press and hold ADD till light turns solid, then enter 998. Reset to factory settings: Press and hold ADD until the light turns solid, enter 954.
8 CODE SEARCH Start with the TV and STB on. Code search sends codes from the database to your TV or STB to search for a match. When the device turns off, a match is found. 1. Press and hold the device you want to search (TV or STB) till light solid, then enter code for region; a. US / Canada: enter 962; b. UK / EU / AUS / NZ enter 961; 2. Press and release On/Off. The light flashes, sending 15 codes to the TV; 3. Either: the device turns off, or the light turns solid.
9 LEARNING Flipper can copy (“learn”) the IR signals from your existing remote control. Each button is programmed separately. When learning TV signals, use the TV button; when learning STB functions, use the STB button. Do this procedure in low light, as light can interfere with the IR signal. 1. 2. 3. 4. 5. 6. 7. Place Flipper and your device remote on a table with the front facing each other; On Flipper, press and hold TV (or STB) and On/OFF at the same time till light starts to flash.
10