T0250 www.fisher-price.
Consumer Information IMPORTANT! PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE. • Please read these instructions before assembly and use of this product. • Adult assembly is required. • Tool needed for assembly: Phillips screwdriver (not included). • When using this product on an adult chair: - Make sure the chair seat is level and larger than the seat base. - DO NOT use on a folding chair. - Check to be sure the floor surface beneath the chair is level.
Parts IMPORTANT! Please remove all parts from the package and identify them before assembly. Tray Rear Base Front Base Hint: Do not remove the plastic inserts inside the tubes of the front base. Footrest Seat with Restraint Seat Back with Restraint Seat Back Pad Seat Pad 2 Frames Seat Support 2 Brackets (Left and Right) Hint: Do not remove the plastic insert inside the tube in each frame.
Assembly CAUTION This package contains small parts in its unassembled state. Adult assembly is required. IMPORTANT! Before assembly and each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Fisher-Price® for replacement parts and instructions if needed. Never substitute parts. 2 • Fit a #8 x ¾" screw with retainer into the rear base and tighten.
Assembly Seat Support Footrest Front Base 4 • Fit the front base into the frame tubes. 6 • Lift the frame assembly upright. • Fit the footrest onto the seat support, as shown. 5 • Insert two #8 x ¾" screws with retainers into the holes in each frame tube and tighten. Hint: If you cannot insert the screws into the frame tubes, you have assembled the front base backwards. Remove it, turn it around and re-assemble it to the frame tubes.
Assembly Seat Support Tube Seat Support Seat Support Tube B B A A 8 Seat Support 10 Left Bracket Right Bracket • First fit the right bracket (labeled 2) onto the seat support tube closest to you A . • Then, slide the right bracket completely onto the seat support B . • Turn the frame over with the footrest facing away from you. • First fit the left bracket (labeled 1) onto the seat support tube closest to you A . • Then, slide the left bracket completely onto the seat support B .
Assembly Pegs Tab Tab Slot Slot Seat Pad Elastic Loops 12 • At an angle, fit the tabs on the seat back into the slots in the seat. • Push the seat back to “snap” in place. • Pull on the seat back to be sure it is secure to the seat bottom. 14 • Pull the ends of the waist belts and crotch belt through the slots in the seat pad. • Fit the elastic loops on the seat pad down through the slots in the seat. • Turn the seat upside down.
Assembly Lower Shoulder Belt Slots Seat Back Pad Straps Seat Back 17 Smaller Baby • Insert the ends of the shoulder belts through the lower slots in the pad and seat back. 15 • Pull the ends of the shoulder belts through the slots in the seat pad. • Fit the straps on the back of the seat back pad into the slots in the seat back pad. • Press to fasten the straps to secure the seat back pad.
Assembly Securing Your Child WARNING 19 Prevent serious injury or death from falls or sliding out: • Only use for a child capable of sitting upright unassisted. • NEVER leave child unattended. High Chair Use: • ALWAYS secure child with restraint belts adjusted to fit your child snugly. The tray is not designed to hold child in the product. When attached to adult chair: • Use restraint belts until child is able to get in and out of the product without help (about 21/2 years old).
Securing Your Child Adjuster Waist/Shoulder Belt Adjuster Waist/Shoulder Belt Crotch Belt 3 • To tighten the waist belts: Feed the anchored end of the waist belt up through the buckle to form a loop A . Pull the free end of the waist belt B . • To tighten the shoulder belts: Hold the adjuster and pull the shoulder belt down C . 1 • Place your child in the seat. Position the crotch belt between your child’s legs. • Fasten both waist/shoulder belts to each side of the crotch belt.
Using the Tray WARNING Release Bar Prevent serious injury or death from falls or sliding out: • ALWAYS secure child with restraint belts adjusted to fit your child snugly. The tray is not designed to hold child in the product. 2 Tray • While pushing the release bar on the front of the tray, adjust the tray forward or backward. Armrest 1 Release Bar • Fit the tray onto the seat armrests. Push down until the tray "snaps" into place.
Adjusting the Seat Attaching To An Adult Chair WARNING Prevent serious injury or death from falls or sliding out: • Only use for a child capable of sitting upright unassisted. • NEVER leave child unattended. • Use restraint belts until child is able to get in and out of the product without help (about 21/2 years old). • NEVER use in motor vehicles. • ALWAYS secure the product on a chair using bottom and back attachment straps. NEVER use on a stool or bench that does not have a seat back.
Attaching To An Adult Chair A B Chair Attachment Straps 3 Latch Door • Turn the seat over. • Slide the door open and pull out the chair attachment straps. 1 Openings • While sliding the switch A pull the latch towards you B . 4 Openings • Match the buckle on each strap to the matching buckle icon near each slot in the seat. Feed each strap through the matching slot on the seat. 2 • Lift the seat off the base.
Attaching To An Adult Chair Remove the Seat Back and Shoulder Belts 5 1 • Turn the seat over and place the seat on a chair. • Wrap the bottom straps around the bottom of the chair A . Buckle the straps B . Make sure you hear a "click". Pull the free end of each strap to tighten on the chair C . • Pull the shoulder belts out of the waist restraint buckle slots. LIFT Seat Back PULL TAB 6 2 • Pull the tab on the seat back. Lift to remove the seat back from the seat.
Storage Attaching the Seat To the Frame Chair Attachment Straps 1 Door • Turn the seat over and open the door. Carefully fit the chair attachment straps into the compartment. • Pull the frame release latches forward and push the rear legs toward the front legs. 2 IMPORTANT! Close the door completely. If you do not close the door, the seat will not fit on the high chair base.
CANADA Mattel Canada Inc., 6155 Freemont Blvd.,Mississauga, Ontario L5R 3W2. Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, New York 14052, U.S.A. ©2010 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.
