Smart Response Swing ™ Product features and decorations may vary from picture above. Accessories sold separately. Model Number: B2108, B3469, G5175 PLEASE KEEP FOR FUTURE REFERENCE. Please read these instructions before assembly and use of this product, as they contain important information. Adult assembly is required. Tool needed for assembly: Phillips Screwdriver (not included). Requires four “D” (LR20) alkaline batteries for operation. Maximum Weight Limit: 24 lbs. (10.9 kg).
Warnings and Caution Consumer Information Occasionally a consumer may experience a problem with one of our products. If this should happen, please call us toll-free, rather than return this product to the store. Usually, we can solve the problem over the telephone or send you replacement parts. Please call Fisher-Price® Consumer Relations, toll-free at 1-800-432-5437, 8 AM - 6 PM EST Monday through Friday. Hearing-impaired consumers using TTY/TDD equipment, please call 1-800-382-7470.
Parts 2 Accessory Bins Housing 2 Rear Legs (Shorter) 2 Front Legs (Longer) Motor Housing Toy Bar (Toys may be different) Front Base Bracket (with M4 Lock Nuts) Rear Base Pad Seat with Restraint 2 Seat Tubes 2 Seat Wire Caps M4 Screw - 4 Shown Actual Size Seat Wire Tray #8 x 13/8" Screw - 6 Shown Actual Size #6 x 5/8" Screw - 8 Shown Actual Size Note: Tighten or loosen all screws with a Phillips screwdriver. Do not over-tighten the screws.
Assembly IMPORTANT! Before assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Fisher-Price® for replacement parts and instructions if needed. Never substitute parts. Housing Front Legs (Longer) Hub Slot Tapered End Motor Housing Press Buttons Press Button Front Legs Press Button Tapered End 1 3 Front Base • Position the housing so that the hub is inward.
Assembly Pull Up Pull Up Pull Rear Leg Pull Rear Leg Rear Legs 5 7 • Pull both rear legs out until they “snap” into place. Rear Base • While standing on the rear base, pull the rear legs up. They should remain secured to the rear base. If you can remove the rear legs, you have not assembled them correctly to the rear base. Reread and repeat assembly step 6. • Set the frame assembly aside for Assembly step 17.
Assembly M4 Lock Nut Rounded Side Bracket Grooves Shown Actual Size Tall End Lock Nut Seat Tubes Bottom Edge of Seat Hexagonal Opening 9 • Position the bracket so that the tall end is toward the bottom edge of the seat. Hint: The M4 lock nuts have been assembled to the bracket at the factory. During shipment of this product, they may have fallen out. Check to be sure there is a lock nut in each hexagonal opening on the bracket.
Assembly Press in Place Seat Wire is Through Hole in Seat Wire Cap Seat Wire Slots 13 Seat Wire Caps 15 • Lift the seat tubes slightly. • With the seat wire hanging down, insert the ends of the seat wire through the slots in the seat, as shown. • Press the seat wire caps into place. • Insert two #6 x 5/8" screws through each seat wire cap and tighten. Rounded Edge Up #6 x 5/8" Screw - 4 Shown Actual Size Hint: The seat wire caps are designed to fit into the seat only one way.
Assembly Frame Hub Push Button Pad Swing Tube Front of Seat Waist Belts 17 Curved Front Base Crotch Belt 19 • Position the seat assembly so that the front of the seat is toward the curved front base. • While pressing the buttons on the swing tubes, insert them into the frame hubs. Push the swing tubes up until the buttons “snap” into the hole in the frame hubs. • Push down on the seat to be sure the seat is secured in both frame hubs. • Fit the pocket on the back of the pad onto the seat back.
Assembly Battery Installation Hint: When swinging, sound or power L.E.D. slows/dims/stops, it’s time to replace the batteries! We recommend using alkaline batteries for longer battery life. Elastic Loop Elastic Loop Battery Compartment Door Installation 21 • Locate the battery compartment door on the swing frame. • Insert a coin into the battery compartment door and pry the battery compartment door off of the swing frame. • Insert four “D” (LR20) alkaline batteries.
Securing Your Child IMPORTANT! Before each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Fisher-Price® for replacement parts and instructions if needed. Never substitute parts. B B WARNING • To prevent serious injury or death from falls and being strangled in the restraint system: - Always use the restraint system. Never rely on the tray to restrain child.
Adjusting the Seat Using the Toy Bar Toy Bar Upright Semi-Recline 3 Recline Adjust the seat angle in any of three positions: Upright, Semi-Recline or Recline. To adjust the seat angle: Push down on the seat back to position the seat wire in the desired groove in the bracket for Upright, Semi-Recline or Recline. 5 • Lift or lower the toy bar for baby's enjoyment. Using the Tray Tray 4 • Fit the tray onto the seat armrests.
Swing Modes The Smart Response™ Swing has two modes: Baby Sounds Activated and Parent Activated . Product features and decorations may vary from pictures below. Accessories sold separately. Parent Activated Baby Sounds Activated IMPORTANT! The maximum weight limit for this product is 24 lbs. If your child weighs less than 24 lbs., but is really active and appears to be able to climb out of the swing, immediately discontinue its use.
Baby Sounds Activated Product features and decorations may vary from picture below. Accessories sold separately. Speed Dial Sound Sensitivity Dial Power L.E.D. Swing Mode Switch Music/Volume Switch Sound Sensitivity Dial • Slide the switch to high sensitivity for incoming sounds (listens for shallow sounds). • Slide the switch to low sensitivity for incoming sounds (listens only for loud sounds). Swing Mode Switch • Slide the switch to baby sounds activated. The power L.E.D. lights.
Parent Activated Product features and decorations may vary from picture below. Accessories sold separately. Power L.E.D. Swing Mode Switch Speed Dial Music/Volume Switch Swing Mode Switch • Slide the switch to parent activated. The power L.E.D. lights and the swing begins swinging. • Be sure to turn the product off when not in use. Speed Dial • Select any of five speed settings. Music/Volume Switch • Select for music highest volume. • Select for music high volume. • Select for music low volume.
Storage Care The pad is machine washable. Wash the pad separately in cold water on the gentle cycle. Do not use bleach. Tumble dry separately on low heat and remove promptly. The frame, tray, and toybar may be wiped clean using a mild cleaning solution and a damp cloth. Press Buttons Upper Pad Pocket Toy Bar Elastic Loops Lower Pad Pocket Elastic Loops Restraint Belts • Turn the toy bar back to it's storage position.
One (1) Year Limited Warranty FCC Statement (United States Only) Fisher-Price, Inc., 636 Girard Avenue, East Aurora, New York 14052 warrants that Smart Response™ Swing is free from all defects in material and workmanship when used under normal conditions for a period of one (1) year from the date of purchase. Should the product fail to perform properly, we will repair or replace it at our option, free of charge.