73528 Please keep this instruction sheet for future reference, as it contains important information. Adult assembly is required. Age: 1½ years - 5 years. Weight Limit: 50 lbs. (23 kg). Tools needed for assembly: Phillips Screwdriver, Hammer and Scrap Block of Wood (all not included). 1 www.fisher-price.
Fasteners Consumer Information WARNING To avoid serious injury: • Adult supervision is required. • Never use near cars and other motor vehicles, near streets, steps, sloped driveways, hills, roadways, alleys, swimming pool areas or other bodies of water. • Always wear shoes or sneakers. • Never allow more than one (1) rider. Cap Nut – 1* *Note: For your convenience, an extra cap nut is included.
Parts Note: The base/handle assembly can be attached to the trike in either the Ride-on Rocker (page 9) or Learn to Pedal (page 10) mode. Seat Pin Seat Parts not shown: Assembly Tool and Label.
Assembly CAUTION Frame This product contains small parts in its unassembled state. Adult assembly is required. Rear Wheel Wheel Cap Hole • Please save all packaging material until assembly is complete to ensure that no parts are discarded. • Please wipe each part with a clean, dry, cloth before assembling this product. 2 Hole Straight Axle Bottom View • Turn the frame upside down. • Insert the straight axle assembly through the holes in the rear of the frame.
Assembly Rear Wheel Spoke Side Up Assembly Tool Wheel Cap Cap Nut 4 Straight Axle • Fit the wheel cap into the center of the wheel. Tap the wheel cap with a hammer to secure it to the wheel. • Set the frame assembly aside. 3 Assembled Rear Wheel Pedal Axle Cover Scrap Block of Wood Pedal Axle • Turn the frame on its side with the exposed end of the straight axle up. • Place the assembled rear wheel on the scrap block of wood.
Assembly Front Wheel Assembly Fork Cover Handlebar Fork Arms Frame Neck Fork Post FIRST, insert the screw so that ¾" is visible. THEN, tighten the screw. 6 Pedal Axle Fork Covers Groove ¾" 7 • Place the front wheel assembly between the fork arms so that the pedal axle fits into the groove at the bottom of each fork arm. • Place a fork cover over the pedal axle on one fork arm. • Insert two #10 x ¾" screws into the fork cover and tighten.
Assembly Knobbed End Seat Frame Opening ➥ 8 Footrest ➥ 1 Footrest Knobbed End 2 ➥ 3 • Insert the knobbed end of the footrest up through the opening in the underside, center of the frame 1 . • Rotate the footrest ¼ turn 2 . Top View • Slide the footrest toward the handlebar as far as it will go until the top of the footrest is positioned over the opening’s rectangular cut-out. • Lower the knobbed end of the footrest into the rectangular cut-out in the frame 3 .
Assembly 11 13 Seat Pin • Insert 13 - #8 x ¾" screws into the handle top and tighten. • While pushing down on the seat, insert the seat pin through the hole in the seat and into a seat mount adjustment hole. Handle Top Base Grooves Handle Bottom 12 Wheel Retainers 14 Base/Handle • Place the base/handle assembly on a flat surface so that the wheel retainers are upright.
Assembly Ride-on Rocker IMPORTANT! Be sure to adjust the seat in the most forward position for Ride-on Rocker mode. Flared End Trike Handle Cover 15 Base/Handle • Position the base/handle covers so that the flared end faces the front of the trike. • Fit the base/handle covers onto the trike rear frame near the rear wheels. • Insert two #10 x ¾" screws into each base/handle cover and tighten. Assembly is now complete.
Learn to Pedal Trike Learn to Pedal Trike Base/Handle 2 • Rotate the base/handle to the upright position. 3 Base/Handle Handle Pin • Insert the handle pin through one side of the base/handle, through the holes in the back of the frame and out through the hole in the other side of the base/handle. Make sure the handle pin “snaps” into place. • Pull on the handle pin to be sure it is secure.
Pedal Trike 1 Base/Handle Handle Pin • If you are converting from the learn to pedal trike mode, remove the handle pin from the base/handle and the back of the frame. Base/Handle 2 • Rotate the base/handle down, under the trike, to the ride-on rocker position.
Pedal Trike Storage Flared End Base/Handle Cover Handle Cover Handle Pin 3 Base/Handle • Remove the screws from the base/handle covers. • Remove the base/handle covers. • Remove the base/handle. Handle Cover Helpful Hint: To store for future use, position the handle covers with the flared end upright and attach them to the handle using the four screws. Insert the handle pin into either the holes in the base/handle or through the holes in the retainers.