P6946 Rocker Swing WARNING IMPORTANT! KEEP INSTRUCTIONS FOR FUTURE REFERENCE. Infant Seat www.fisher-price.co.
Consumer Information • IMPORTANT! PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE, AS THEY CONTAIN IMPORTANT INFORMATION. • Please read these instructions before assembly and use of this product. • Adult assembly is required. Tools needed for assembly: Phillips screwdriver (not included) and assembly tool (included). • Requires four “D” (LR20) alkaline batteries (not included) for swing operation. • In Swing mode, only to be used by children that cannot climb out of seat.
Parts IMPORTANT! Please remove all parts from the package and identify them before assembly. Some parts may be packed inside the pad. Toy Bar (Toys may be different) Pad 2 Retainers (with Lock Nut) Seat Tube Support 2 Seat Tubes Motor Housing Housing Seat Back Tube 2 Retainers (with Lock Nut) 2 Legs Cross Brace 2 Side Rails with Waist Belts Back Base Front Curved Base Front Tube Note: Tighten or loosen screws with a Phillips screwdriver or the assembly tool. Do not over-tighten the screws.
Infant Seat/Rocker Assembly CAUTION Side Rail Hole Side Rail Hole This package contains small parts in its unassembled state. Adult assembly is required. Front Tube Cross Brace PRESS PRESS 3 1 • Insert a M5 x 2,9 cm screw through the outside of each side rail and into the ends of the front tube. IMPORTANT! Please follow the next assembly (step 4) carefully to completely secure the front tube to the side rails.
Infant Seat/Rocker Assembly Seat Back Tube PRESS Lower Pocket Hardboard Sockets 5 • Insert the seat back tube into the socket in each side rail. • While pressing the tabs on the ends of the seat back tube, continue to insert the seat back tube into the sockets in each side rail until the tabs “snap” into place. Make sure you hear a “snap” on each side. • Pull the seat back tube up to be sure it is secure in the side rail sockets.
Infant Seat/Rocker Assembly Swing Frame Assembly Housing Pad Buckles Leg Button 1 8 • • • • Place a housing on a flat surface. Insert the button end of a leg into the hole in the housing. Push the leg in until it “snaps” into the housing. Repeat this procedure to assemble the other leg to the other housing. • Pull the legs to be sure they are secure in the housings. If you can remove them, you have not assembled them correctly. Please re-read and repeat this assembly step.
Swing Frame Assembly CORRECT HUBS FACE IN Hubs Back Base 3 FRONT BASE CURVES INWARD Front Curved Base • Place the front curved base on a flat surface so that it curves away from you. • Place the back base on a flat surface, behind the front curved base. • Position the leg assemblies so that the hubs are facing each other. • Fit the ends of the legs over the ends of the front and back bases, as shown. Hint: You may need the help of another adult to help you balance the assembly.
Swing Frame Assembly Hubs Seat Tubes Seat Tube Support Seat Tubes 5 7 • Insert the ends of the seat tubes into the sockets in the hubs. • Push the seat tubes in until you hear a “snap” (for each). • Locate the holes on the bottom of the seat tubes. • Position the seat tube support so that it is a shape. • Fit the seat tube support to the seat tubes. Hold the seat tube support in place and proceed to step 8. 6 8 • Insert a #4 x 3,18 cm screw into each hub and tighten.
Swing Frame Assembly Battery Installation 1,5V x 4 “D” (LR20) Battery Compartment Retainer with Lock Nut 9 • Loosen the screws in the battery compartment door and remove the battery compartment door. • Insert four “D” (LR20) alkaline batteries into the battery compartment. • Replace the battery compartment door and tighten the screws. Hint: We recommend using alkaline batteries for longer battery life. • If this product begins to operate erratically, you may need to reset the electronics.
Setup and Use WARNING To prevent injury or death from falls or being strangled in the restraint system • Never leave child unattended. When used as a Swing: • Always use the restraint system. • Never use with an active child who may be able to climb out of the product. When used as an Infant Seat or Rocker: • Fall Hazard - It is dangerous to use this product on an elevated surface. Use only on a floor.
Swing Seat Tubes Handles Groove Indented Area in Seat Handle Seat Tube Hub Seat Tube Hub 2 • Now, lower the seat down onto the red seat tube hubs. Hint: The seat tube hubs should fit into the red, indented area on the seat handles. • Push the seat down to be sure it is secure. Kickstand 1 • Rotate the kickstand up. • Push down on the seat bottom to be sure the kickstand is in position. • Grasp the handles on the seat. • Slide the seat between the seat tubes.
Swing Power Indicator Music/Volume Button Power Switch 6 Power Switch • Make sure your child is properly secured in the seat. • Slide the swing power switch on to either of two speed settings. The power indicator lights. • To start swinging motion, give the seat a light push. • Be sure to turn this product off when not in use. Slide the power switch OFF. Hints • As with most battery-powered swings, a heavier child will reduce the amount of swinging motion on all settings.
Infant Seat Rocker Kickstand Kickstand 1 1 • Rotate the kickstand out. • Push down on the seat bottom to be sure the kickstand is in position. • Rotate the kickstand up. • Push down on the seat bottom to be sure the kickstand is in position. Toy Bar Toy Bar Plugs Plugs 2 2 • Fit the plugs on each end of the toy bar into the sockets in each side rail. • Fit the plugs on each end of the toy bar into the sockets in each side rail.
Securing Your Child Restraint Strap Anchored End Free End 3 1 Anchored End Free End TIGHTEN LOOSEN To tighten the restraint straps: • Feed the anchored end of the restraint strap up through the buckle to form a loop A. Pull the free end of the restraint strap B. To loosen the restraint straps: • Feed the free end of the restraint strap up through the buckle to form a loop A. Enlarge the loop by pulling on the end of the loop toward the buckle.
Removing the Seat from the Swing Handles B A Seat Tube Hubs • Grasp handles on the seat. • Lift the seat from the seat tube hubs A. • Pull the seat forward B.
Storage PRESS Care • The pad is machine washable. Wash it separately in cold water on the gentle cycle. Do not use bleach. Tumble dry separately on low heat and remove promptly. • The frames and toy bar can be wiped clean using a mild cleaning solution and a damp cloth. Do not use bleach. Do not use harsh or abrasive cleaners. Rinse clean with water to remove residue. Pad Pad Buckles • Press the button on each housing and push the rear legs toward the front legs.