P5755 IMPORTANT! KEEP INSTRUCTIONS FOR FUTURE REFERENCE. www.fisher-price.co.
Consumer Information IMPORTANT! Place the high chair on a level, stable surface away from electrical flexes. Be sure to keep electrical flexes out of child's reach. • Please read these instructions before assembly and use of this product. • Adult assembly is required. • Tool needed for assembly: Phillips Screwdriver (not included). • Product features and decorations may vary from the photograph.
Assembled Parts CAUTION This package contains small parts in its unassembled state. Adult assembly is required. Pad Seat Back Seat Bottom 2 Frames Hinge Rod Back Base Front Base Footrest Food Tray Note: Tighten or loosen all screws with a Phillips screwdriver. Do not over-tighten the screws.
Assembly IMPORTANT! Before assembly and each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Fisher-Price® for replacement parts and instructions if needed. Never substitute parts. Footrest Seat Bottom 1 • Place the seat bottom face down on a flat surface. • At an angle, fit the footrest on the seat bottom, as shown. 3 Plastic Rings • Align the holes in the plastic rings and the seat bottom tubes.
Assembly Insert Screws Here Hinge Hinge Rod 4 6 • Insert two #10 x 2,2 cm black screws through the footrest and into the seat bottom. Tighten the screws. This may require extra force. • Turn the seat assembly face down. • Insert the hinge rod through the hinge on the seat back and seat bottom, as shown. • Insert a #10 x 2,2 cm black screw into the hinge rod. Tighten the screw. • Set the seat assembly aside for Assembly step 9.
Assembly Frame Leg Seat Height Adjusters Position 4 Frame Decorated Side Frame Back Legs Press Lever 8 • While pressing the levers on the seat height adjusters, lift them to position 4 on the frame front legs, as shown. Seat Assembly Base Screw Retainers Sockets Sockets 7 Seat Bottom Tubes • Pull the frame leg out on each frame to open. Make sure it "clicks" into place. • Position a frame so that the decorated side is outward. • Fit the end of a base into the back leg of a frame.
Assembly Seat Height Adjuster Screw Retainers Base 10 Seat Bottom Tube Ends • Fit the frame front legs onto the remaining base. • Fit a screw retainer over a hole in the front leg. • Insert a #10 x 2,2 cm black screw through the screw retainer and front leg. Tighten the screw. • Repeat this procedure to secure the other end of the base with the remaining screw retainer and #10 x 2,2 cm black screw. Hint: The #10 x 2,2 cm black screws may have been assembled to the screw retainers.
Assembly Pad Slot Elastic Loops Hole Hole Crotch Belt FRONT VIEW 14 • Insert the crotch belt through the slot in the pad. Make sure the crotch belt is not twisted. Tabs Elastic Loops 13 BACK AND BOTTOM VIEW • Lift the bottom of the pad. Insert the two elastic loops on the pad through the holes in the seat bottom. • From the back and bottom of the seat, hook the elastic loops to the tabs on the seat.
Assembly Upper Shoulder Belt Slots Shoulder Portion Shoulder Portion 15 Lower Shoulder Belt Slots • Fold the top of the pad down. • Remove the shoulder portion of the waist/shoulder belts by feeding them through the slots in the seat back. 17 • Insert the shoulder portion of the shoulder/waist belt through the slots in the pad and seat back. - Use the lower shoulder belt slots for a smaller baby. - Use the upper shoulder belt slots for a larger baby. • Fit the top of the pad over the seat back.
Secure Child WARNING Prevent serious injury or death from falls or sliding out: • The child should at all times wear a safety harness correctly fitted and adjusted. The tray is not designed to hold the child in the chair. • Do not use the high chair unless all components are correctly fitted and adjusted. Waist/Shoulder Belt Waist/Shoulder Belt 2 • Tighten each waist belt and shoulder belt so that the restraint system is snug against your child.
Secure Child Shoulder Portion Hold Adjuster Pull Down Strap Slide Adjuster Down TIGHTEN LOOSEN 4 6 To tighten the shoulder belts: Hold the adjuster and pull the front shoulder strap down. To loosen the shoulder belts: Slide the adjuster down. Note: After adjusting the restraint system to fit your child, make sure you pull on it to be sure it is securely fastened.
Using the Trays WARNING Prevent serious injury or death from falls or sliding out. The child should at all times wear a safety harness correctly fitted and adjusted. The tray is not designed to hold the child in the chair. Base Tray 8 Armrest • While pushing the release bar on the front of the base tray, adjust the base tray forward or backward. Armrest 7 • Fit the base tray onto the seat armrests. Push down until the base tray "snaps" into place.
Using the Trays Food Tray Base Tray 9 10 • While pushing the release bar on the front of the base tray, pull the tray base towards you and remove. • Fit the food tray into the base tray, as shown. Hint: Before use, thoroughly wash all parts (the trays) that may contact food. The food tray is not microwave safe.
Adjusting the Seat Hint: Adjust the seat height to any of seven positions! WARNING Prevent serious injury or death from falls or sliding out: It is recommended that only children capable of sitting upright unassisted use the high chair in the upright position. Hint: Adjust the seat angle to any of three positions: Upright, Semi-Recline or Recline.
Storage Care • The restraint system, pad, frame, trays and tray toy may be wiped clean using a mild cleaning solution and a damp cloth. Do not use bleach. • The food tray is also top rack dishwasher safe (or use bottom rack - without using the drying cycle). To remove the pad: • Remove the elastic loops from the pegs on the back of the seat. • From behind the product, squeeze the restraint release tabs and remove the restraint system from the peg.
Great Britain: Vanwall Business Park, Maidenhead SL6 4UB. Helpline: 01628 500303. www.service.mattel.com/uk. Asia: Mattel East Asia Ltd, Room 1106, South Tower, World Finance Centre, Harbour City, Tsimshatsui, HK, China. Malaysia: Diimport & Diedarkan Oleh: Mattel SEA Ptd Ltd. (993532-P) Lot 13.5, 13th Floor, Menara Lien Hoe, Persiaran Tropicana Golf Country Resort, 47410 PJ. Tel: 03-78803817, Fax: 03-78803867. Fisher Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A.