M7949 WARNING www.fisher-price.com.au IMPORTANT! KEEP INSTRUCTIONS FOR FUTURE REFERNCE.
Important! WARNING To prevent strangulation with power cord, never place transmitter within reach of child. CAUTION This product cannot replace responsible adult supervision. CAUTION To reduce the risk of electric shock, do not expose to rain or moisture.
Important! • For proper setup and use, please read these instructions. • Please keep this instruction sheet for future reference, as it contains important information. • Transmitter operates on AC current. • Receiver operates on AC current (use enclosed AC adaptor) or a 3.6V, 350mAH nickel metal hydride rechargeable battery pack (included). • Before first-time use, charge the rechargeable battery pack for 10-12 hours (please see page 6 for instructions).
Consumer Information AUSTRALIA: Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870, Richmond, Victoria 3121 Australia. Consumer Advisory Service 1300 135 312. NEW ZEALAND: 16-18 William Pickering Drive, Albany 1331, Auckland. Fisher-Price, Inc., a subsidiary of Mattel, Inc. East Aurora, New York 14052, U.S.A. ©2008 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.
Features 9 11 12 3 8 10 4 4 2 7 13 14 1 5 6 1 Transmitter 2 Power Indicator 3 LCD Screen – shows which channel you are on. 4 Channel Button 5 Power Button 6 Microphone 7 Receiver 8 On/Off/Volume Dial – Turns power on. Set volume to a comfortable level. 9 Clip (backside of receiver) – Fasten to your clothes to stay in touch with baby around the house or yard. 10 Channel Button 11 Sound Lights – let you see baby’s sounds.
Receiver Battery Installation Socket Battery Connector • Locate the battery compartment door on the back of the receiver. • Loosen the screws in the battery compartment door with a Phillips screwdriver. Remove the battery compartment door. • Plug the battery connector into the receiver socket. Hint: If the battery connector will not plug into the socket, turn it over and try again. Do not force the battery connector into the receiver socket. • Replace the battery compartment door.
Charging the Battery Even with proper care, the rechargeable battery will not last forever. The life of the rechargeable battery depends on how well you follow these instructions and the total number of hours it is used. If you should need to replace the rechargeable battery, contact Fisher-Price®. • Use the power cord only in a wall outlet. Do not plug the power cord into a ceiling light. • Insert the AC adaptor jack into the receiver and then plug into a wall outlet.
Testing Sound Reception Test transmitter transmission and receiver reception each time you change location of use. Channel LCD Screen Power Button • Place the transmitter in the room in which you intend to use it. • Press the transmitter power button to turn power on. Power indicator lights and the LCD screen turns on. • Press the channel buttons on the transmitter to select a channel.
Testing Sound Reception On/Off/Volume Dial LCD Screen • Place the receiver in the room in which you intend to use it. • Rotate the receiver on/off/volume dial to turn power on. The LCD screen turns on. • Look at the LCD screen to see current channel selected. • Press the channel button on the receiver to select the same channel as the transmitter. • Adjust receiver location.
Testing Sound Reception Good Reception No Reception/Out of Range Check reception! If you see bars on the LCD, you have reception. If you are out of range, the reception display will blink and you will hear a low pitched beep. Full Charge Half Charged No Charge Check to be sure there is enough battery power. Hint: You will hear a high pitched beep if battery power is low. We recommend using the AC adaptor for power source (and you’ll charge the battery too).
Testing Sound Reception • Sound lights on the receiver turn on when sound is received by a receiver. - One or two lights for shallow sounds. - Three or more lights for louder sounds. • If reception is poor, or there is no reception on one channel, change the channel on both units.
Setup & Use IMPORTANT! Test sound reception of this monitor before first time use and whenever you change location of transmitter (see page 8). Adjust Channel • Set transmitter channel switch to same channel as the receiver. • Place transmitter in same room with child. Point the microphone directly toward crib or play area. • Unwrap and fully extend power cord for best transmission. Plug power cord into wall outlet. • Use the power cord only in a wall outlet.
Setup & Use • Place the receiver where you will see or hear it. • If desired, use the AC adaptor. Unwrap and fully extend the AC adaptor cord for best reception. Insert the AC adaptor jack into the receiver socket and plug into a wall outlet. • Rotate the receiver on/off/volume dial to turn the power on. LCD screen turns on. Rotate the on/off/volume dial to adjust volume.
Setup & Use • Clip the receiver to your clothes to stay in touch with baby around your house or yard.
Problems & Solutions Problem You hear static or buzzing Reception display on receiver LCD screen flashes and you hear a low pitched beep Solution There may be a physical obstruction or noise level causing interference. Change the location of reciever or try a different channel. Range varies depending on surrounding conditions such as noise levels, physical obstructions and signal interference. Transmitter power is off. Turn transmitter power on. Transmitter and receiver are on different channels.
One (1) Year Limited Warranty Mattel Australia Pty., Ltd., (658 Church Street, Locked Bag #870, Richmond, Victoria 3121 Australia) warrants to the original owner that this product is free from all defects in material and workmanship when used under normal conditions for a period of one (1) year from the date of purchase. Should the product fail to perform properly, we will repair replace it at our option, free of charge.
