M7596 www.fisher-price.
CONSUMER INFORMATION FCC Statement (United States Only) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
ASSEMBLED PARTS Note: Label sheet not shown. Rear Axle 2 Front Axles Roof 2 Axle Mounts 4 Wheels 4 Hubcaps Sounds and Lights Box Retainer Cup Holder 2 Rear Bushings 4 Wheel Covers 2 Front Bushings 2 Cap Nut Covers 4 Roof Posts Steering Wheel Key / ” Washer – 4 3 16 .354 Cap Nuts – 6 #6 x 1/2” Screw – 3 #8 x 3/4” Screw – 11 ALL SHOWN ACTUAL SIZE Note: Tighten and loosen all screws with a Phillips screwdriver. Do not over-tighten the screws.
BATTERY INSTALLATION BATTERY SAFETY INFORMATION In exceptional circumstances, batteries may leak fluids that can cause a chemical burn injury or ruin your product. To avoid battery leakage: • Do not mix old and new batteries or batteries of different types: alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium). • Insert batteries as indicated inside the battery compartment. • Remove batteries during long periods of non-use. Always remove exhausted batteries from the product.
ASSEMBLY 1 2 Sounds and Lights Box 2 Front Bushing 3/16” Washer Front Axle Retainer • Slide a 3/16” washer onto the front axle labeled 2. • Then, slide a front bushing, flat side first, onto the front axle. Frame BOTTOM VIEW • Turn the frame on its side. • Fit the sounds and lights box onto the dash on topside of the vehicle. • Then, fit the retainer over the battery compartment door on the underside of the frame. Insert four #8 x 3/4” screws into the retainer and tighten.
ASSEMBLY 5 6 Cap Nut 3 16” / 2 Washer Frame Front End Front Axle Front Axle • Fit a cap nut onto the end of the front axle, as shown. • Tap the cap nut with a hammer. • Gently pull the front wheel down to be sure the cap nut is securely attached to the front axle. • Repeat assembly steps 2-6 to assemble the front axle labeled 1, a wheel, a front bushing, a 3/16” washer, two cap nuts and a wheel cover. FRONT VIEW • First, slide a 3/16” washer onto the front axle.
ASSEMBLY 7 8 Cap Nut Covers Axle Mount BOTTOM VIEW • Fit a cap nut cover over each cap nut on the front end of the frame. Push to “snap” in place. 11 • Turn the frame upside down on a flat surface. • Fit an axle mount onto the pegs near the rear of the frame. Hint: Each axle mount only fits on one side of the vehicle. If it does not line up with the pegs on the frame, try fitting it to the other side. • Insert three #8 x ¾” screws into the axle mount and tighten.
ASSEMBLY 13 14 Cap Nut Cover Cap Nut • Fit a cap nut onto the end of the rear axle. • Tap the cap nut with a hammer. Gently pull the wheel to make sure the cap nut is securely attached to the rear axle. Hint: You may need the help of another adult to hold the rear axle in place while you tap the cap nut. 17 • Fit a cap nut cover onto each rear wheel and push to “snap” in place. 18 Posts Roof Assembly Roof • Fit the roof assembly onto the frame. Push near each post to “snap” in place.
ASSEMBLY 15 16 Steering Wheel Key Sounds and Lights box • Turn the frame upright. • Fit the steering wheel onto the sounds and lights box. • Insert three #6 x ½” screws into the steering wheel and tighten. • Fit the key into the hole in the dash. Push to “snap” in place. 19 Cup Holder • Fit the cup holder onto the side of the frame. • Insert a #8 x ¾” screw into the cup holder and tighten.
LABELS • Before applying the labels, wipe the surface of the vehicle with a clean, dry cloth to remove any dust or oils. • Place the labels exactly as shown in the illustrations. For best results, avoid repositioning a label once it has been applied to the vehicle. • After applying a label, rub the label firmly with a clean, dry cloth to make sure the label is adhered to your vehicle. Start at the center of a label, and smooth towards the outer edges to remove air bubbles.
USE Press the horn on the steering wheel for fun car songs and lights! Real working door! 11
For countries outside the United States: CANADA Questions? 1-800-432-5437. Mattel Canada Inc., 6155 Freemont Blvd., Mississauga, Ontario L5R 3W2; www.service.mattel.com. GREAT BRITAIN: Mattel UK Ltd, Vanwall Business Park, Maidenhead SL6 4UB. Helpline: 01628 500303; www.service.mattel.com/uk. AUSTRALIA: Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870, Richmond,Victoria 3121 Australia. Consumer Advisory Service 1300 135 312. NEW ZEALAND: 16-18 William Pickering Drive, Albany 1331, Auckland.