M2055 www.fisher-price.
Consumer Information IMPORTANT! Please keep these instructions for future reference, as they contain important information. • Please read these instructions before use of this product. • Adult assembly is required. Tool needed for assembly: Phillips Screwdriver (not included). • Requires three “C” (LR14) alkaline batteries (not included) for operation. • Product features and decoration may vary from photos.
Parts IMPORTANT! Please remove all parts from the package and identify them before assembly. Some parts may be packed inside the pad.
Assembly IMPORTANT! Before assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Mattel for replacement parts and instructions if needed. Never substitute parts. Front Base Turn Tube Ends Up 2 1 Seat Back Tube Handles • Insert the ends of the front base into the holes in the handles.
Assembly Back Base PRESS PRESS 3 Front Base 4 Handle Tubes • While pressing the buttons on the ends of the back base, insert it into the tubes in the handle. Make sure the back Soothing Unit Groove • Turn the assembly upright. • Position the soothing unit upright and fit the groove to the front base, as shown. • Insert two 4 mm x 30 mm screws through the front base and into the soothing unit. Tighten the screws. base “snaps” into place.
Assembly Upper Flap Seat Back Tube Front Base 5 Lower Pocket Strap • Fit the upper flap on the pad around the seat back tube. 6 Side Flap • Fit the pad lower pocket around the front base and soothing unit. • Turn the assembly face down. • Fasten both pad side flaps to the strap on the back of the pad. Make sure you hear a “snap” on both sides.
Assembly B Infant Support Toy Bar A Socket 8 • Place the infant support on top of the pad. • Insert the restraint pad through the slot in the infant support. Make sure the restraint pad is not twisted. • Thread the restraint straps through the slots in the infant support. Assembly is now complete. 7 • Fit the toy bar into the socket in the handle A. Turn the toy bar to secure in place B. • Attach the butterfly toy to any of the fastener tabs on the sides of the pad or toy bar, as shown.
Battery Installation 1.5V x 3 “C” (LR14) Battery Compartment Hint: We recommend using an alkaline batteries for longer battery life. • Protect the environment by not disposing of this product with household waste (2002/96/EC). Check your local authority for recycling advice and facilities (Europe only). 2 • Loosen the screw in the battery compartment door and remove the battery compartment door. • Insert three “C” (LR14) alkaline batteries into the battery compartment.
Setup and Use Restraint Pad WARNING To prevent serious injury or death: • Fall Hazard - It is dangerous to use this reclined cradle on an elevated surface, since child’s movement may cause product to slide or tip over. Use only on a floor. • Suffocation Hazard - Never use on a soft surface (bed, sofa, cushion) since the product can tip over and cause suffocation in soft surfaces. • Never use the toy bar as a handle. • Always use the restraint system. • Never leave child unattended.
Soothing Unit Storage Button Back Tube • While pressing the buttons on the handles, push the back tube towards the front tube. Hint: To set-up this seat again, simply pull the back tube back until it “snaps” into place. • Make sure your child is properly secured in the seat. • Slide the power switch to for music. • Slide the power switch to for vibrations. • Slide the power switch to music and vibrations. • Slide the power switch to off to turn vibrations and music off.
Care • The pad, butterfly and infant support are machine washable. Wash them separately in cold water on the gentle cycle. Do not use bleach. Tumble dry separately on low heat and remove promptly. • The frame and toy bar may be wiped clean using a mild cleaning solution and a damp cloth. Do not use bleach. Do not use harsh or abrasive cleaners. Rinse clean with water to remove residue. 1 To remove the pad: • Place the seat face down on a flat surface. • Unfasten the side buckles.
www.service.fisher-price.com/uk 01628 500303 GREAT BRITAIN Mattel UK Ltd, Vanwall Business Park, Maidenhead SL6 4UB. Helpline: 01628 500303; www.service.mattel.com/uk. AUSTRALIA Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870, Richmond, Victoria 3121 Australia. Consumer Advisory Service 1300 135 312. NEW ZEALAND 16-18 William Pickering Drive, Albany 1331, Auckland. ASIA Mattel East Asia Ltd, Room 1106, South Tower, World Finance Centre, Harbour City, Tsimshatsui, HK, China.